(gelöst)USV
-
@ostseereiter sagte in USV:
und in der /etc/nut/nut.conf steht diese beiden Sachen drin.
beides zusammen in ein und der selben Datei??
server gehört da rein wo die USV dran hängt
client bei allen anderen Geräten, die entsprechend mit gesteuert werden sollen@ostseereiter sagte in USV:
ich dachte es müssen alle Rechner rein
nein nur dein Server
-
@ostseereiter sagte in USV:
in welcher Datei kommt dann die Clients?
du musst doch an jedem Gerät/Rechner den du mit steuern möchtest, ebenfalls dieses ausführen
Clients / Slaves einrichten (z.B. Server, andere Computer) Zuerst müssen auf einem Client die notwendigen Pakete installiert werden: sudo apt-get install nut-client Diesmal müssen wir nur zwei Dateien editieren. In der /etc/nut/nut.conf legen wir den Modus fest: MODE=netclient Danach müssen wir wieder upsmon sagen, welche UPS er überwachen soll (in /etc/nut/upsmon.conf): MONITOR gxt4@192.168.1.2 upsremote geheim slave Die IP und das Passwort müssen natürlich noch angepasst werden. Bitte auch das slave am Ende beachten! Zuletzt noch den entsprechenden Service neu starten und überprüfen, ob alles läuft: $ sudo systemctl restart nut-client $ sudo systemctl status nut-clientumgestiegen von Proxmox auf Unraid
-
@ostseereiter sagte in USV:
in welcher Datei kommt dann die Clients?
du musst doch an jedem Gerät/Rechner den du mit steuern möchtest, ebenfalls dieses ausführen
Clients / Slaves einrichten (z.B. Server, andere Computer) Zuerst müssen auf einem Client die notwendigen Pakete installiert werden: sudo apt-get install nut-client Diesmal müssen wir nur zwei Dateien editieren. In der /etc/nut/nut.conf legen wir den Modus fest: MODE=netclient Danach müssen wir wieder upsmon sagen, welche UPS er überwachen soll (in /etc/nut/upsmon.conf): MONITOR gxt4@192.168.1.2 upsremote geheim slave Die IP und das Passwort müssen natürlich noch angepasst werden. Bitte auch das slave am Ende beachten! Zuletzt noch den entsprechenden Service neu starten und überprüfen, ob alles läuft: $ sudo systemctl restart nut-client $ sudo systemctl status nut-clientsudo systemctl status nut-client
Ja nun habe ich auf den Client das installiert und natürlich eingetragen in den beiden Dateien
dann gestartet. und geschaut ob es läuft dabei kam das raus.pi@SVPi-hole:~ $ sudo systemctl restart nut-client Job for nut-monitor.service failed because the control process exited with error code. See "systemctl status nut-monitor.service" and "journalctl -xe" for details. pi@SVPi-hole:~ $ sudo systemctl status nut-client ● nut-monitor.service - Network UPS Tools - power device monitor and shutdown co Loaded: loaded (/lib/systemd/system/nut-monitor.service; enabled; vendor pres Active: failed (Result: exit-code) since Fri 2021-05-21 09:30:38 CEST; 17s ag Process: 9283 ExecStart=/sbin/upsmon (code=exited, status=1/FAILURE) May 21 09:30:38 SVPi-hole systemd[1]: Starting Network UPS Tools - power device May 21 09:30:38 SVPi-hole upsmon[9283]: fopen /var/run/nut/upsmon.pid: No such f May 21 09:30:38 SVPi-hole upsmon[9283]: Using power down flag file /etc/killpowe May 21 09:30:38 SVPi-hole upsmon[9283]: Unable to use old-style MONITOR line wit May 21 09:30:38 SVPi-hole upsmon[9283]: Convert it and add a username to upsd.us May 21 09:30:38 SVPi-hole upsmon[9283]: Fatal error: unusable configuration May 21 09:30:38 SVPi-hole upsmon[9283]: Network UPS Tools upsmon 2.7.4 May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Control process exite May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Failed with result 'e May 21 09:30:38 SVPi-hole systemd[1]: Failed to start Network UPS Tools - power lines 1-15/15 (END)...skipping... ● nut-monitor.service - Network UPS Tools - power device monitor and shutdown controller Loaded: loaded (/lib/systemd/system/nut-monitor.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 09:30:38 CEST; 17s ago Process: 9283 ExecStart=/sbin/upsmon (code=exited, status=1/FAILURE) May 21 09:30:38 SVPi-hole systemd[1]: Starting Network UPS Tools - power device monitor and shutdown controller... May 21 09:30:38 SVPi-hole upsmon[9283]: fopen /var/run/nut/upsmon.pid: No such file or directory May 21 09:30:38 SVPi-hole upsmon[9283]: Using power down flag file /etc/killpower May 21 09:30:38 SVPi-hole upsmon[9283]: Unable to use old-style MONITOR line without a username May 21 09:30:38 SVPi-hole upsmon[9283]: Convert it and add a username to upsd.users - see the documentation May 21 09:30:38 SVPi-hole upsmon[9283]: Fatal error: unusable configuration May 21 09:30:38 SVPi-hole upsmon[9283]: Network UPS Tools upsmon 2.7.4 May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Control process exited, code=exited, status=1/FAILURE May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Failed with result 'exit-code'. May 21 09:30:38 SVPi-hole systemd[1]: Failed to start Network UPS Tools - power device monitor and shutdown controller. ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ lines 1-15/15 (END)Gruß OSR
Plattform
Linux x64 CPUs2 AMD G-T56N Processor 1646 MHz 8GB RAM -
sudo systemctl status nut-client
Ja nun habe ich auf den Client das installiert und natürlich eingetragen in den beiden Dateien
dann gestartet. und geschaut ob es läuft dabei kam das raus.pi@SVPi-hole:~ $ sudo systemctl restart nut-client Job for nut-monitor.service failed because the control process exited with error code. See "systemctl status nut-monitor.service" and "journalctl -xe" for details. pi@SVPi-hole:~ $ sudo systemctl status nut-client ● nut-monitor.service - Network UPS Tools - power device monitor and shutdown co Loaded: loaded (/lib/systemd/system/nut-monitor.service; enabled; vendor pres Active: failed (Result: exit-code) since Fri 2021-05-21 09:30:38 CEST; 17s ag Process: 9283 ExecStart=/sbin/upsmon (code=exited, status=1/FAILURE) May 21 09:30:38 SVPi-hole systemd[1]: Starting Network UPS Tools - power device May 21 09:30:38 SVPi-hole upsmon[9283]: fopen /var/run/nut/upsmon.pid: No such f May 21 09:30:38 SVPi-hole upsmon[9283]: Using power down flag file /etc/killpowe May 21 09:30:38 SVPi-hole upsmon[9283]: Unable to use old-style MONITOR line wit May 21 09:30:38 SVPi-hole upsmon[9283]: Convert it and add a username to upsd.us May 21 09:30:38 SVPi-hole upsmon[9283]: Fatal error: unusable configuration May 21 09:30:38 SVPi-hole upsmon[9283]: Network UPS Tools upsmon 2.7.4 May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Control process exite May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Failed with result 'e May 21 09:30:38 SVPi-hole systemd[1]: Failed to start Network UPS Tools - power lines 1-15/15 (END)...skipping... ● nut-monitor.service - Network UPS Tools - power device monitor and shutdown controller Loaded: loaded (/lib/systemd/system/nut-monitor.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 09:30:38 CEST; 17s ago Process: 9283 ExecStart=/sbin/upsmon (code=exited, status=1/FAILURE) May 21 09:30:38 SVPi-hole systemd[1]: Starting Network UPS Tools - power device monitor and shutdown controller... May 21 09:30:38 SVPi-hole upsmon[9283]: fopen /var/run/nut/upsmon.pid: No such file or directory May 21 09:30:38 SVPi-hole upsmon[9283]: Using power down flag file /etc/killpower May 21 09:30:38 SVPi-hole upsmon[9283]: Unable to use old-style MONITOR line without a username May 21 09:30:38 SVPi-hole upsmon[9283]: Convert it and add a username to upsd.users - see the documentation May 21 09:30:38 SVPi-hole upsmon[9283]: Fatal error: unusable configuration May 21 09:30:38 SVPi-hole upsmon[9283]: Network UPS Tools upsmon 2.7.4 May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Control process exited, code=exited, status=1/FAILURE May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Failed with result 'exit-code'. May 21 09:30:38 SVPi-hole systemd[1]: Failed to start Network UPS Tools - power device monitor and shutdown controller. ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ lines 1-15/15 (END)@ostseereiter irgendwo hast du etwas falsch eingetragen und daher läuft dein service nicht
prüfe doch mal da(Server), wo deine USV dran hängt, das muss erst mal korrekt laufen
sudo systemctl status nut-server sudo systemctl status nut-clientdanach an deinem Client(SLave) die config überprüfen, ob alles richtig eingetragen ist, danach
sudo systemctl restart nut-client sudo systemctl status nut-clientwas mir noch aufgefallen ist, deine 3 user,
upsmaster] password = xxxxxxx actions = SET instcmds = ALL upsmon master [raspiuser] password = xxxxx upsmon slave [upskino] password = xxxx upsmon slavereichen eigentlich 2, einmal master, einmal slave, diese musst du ja in der jeweiligen .conf hinterlegen
umgestiegen von Proxmox auf Unraid
-
@ostseereiter irgendwo hast du etwas falsch eingetragen und daher läuft dein service nicht
prüfe doch mal da(Server), wo deine USV dran hängt, das muss erst mal korrekt laufen
sudo systemctl status nut-server sudo systemctl status nut-clientdanach an deinem Client(SLave) die config überprüfen, ob alles richtig eingetragen ist, danach
sudo systemctl restart nut-client sudo systemctl status nut-clientwas mir noch aufgefallen ist, deine 3 user,
upsmaster] password = xxxxxxx actions = SET instcmds = ALL upsmon master [raspiuser] password = xxxxx upsmon slave [upskino] password = xxxx upsmon slavereichen eigentlich 2, einmal master, einmal slave, diese musst du ja in der jeweiligen .conf hinterlegen
@crunchip OK ich kontrolliere noch mal alles und dokumentiere das dann hier.
-
sudo systemctl status nut-client
Ja nun habe ich auf den Client das installiert und natürlich eingetragen in den beiden Dateien
dann gestartet. und geschaut ob es läuft dabei kam das raus.pi@SVPi-hole:~ $ sudo systemctl restart nut-client Job for nut-monitor.service failed because the control process exited with error code. See "systemctl status nut-monitor.service" and "journalctl -xe" for details. pi@SVPi-hole:~ $ sudo systemctl status nut-client ● nut-monitor.service - Network UPS Tools - power device monitor and shutdown co Loaded: loaded (/lib/systemd/system/nut-monitor.service; enabled; vendor pres Active: failed (Result: exit-code) since Fri 2021-05-21 09:30:38 CEST; 17s ag Process: 9283 ExecStart=/sbin/upsmon (code=exited, status=1/FAILURE) May 21 09:30:38 SVPi-hole systemd[1]: Starting Network UPS Tools - power device May 21 09:30:38 SVPi-hole upsmon[9283]: fopen /var/run/nut/upsmon.pid: No such f May 21 09:30:38 SVPi-hole upsmon[9283]: Using power down flag file /etc/killpowe May 21 09:30:38 SVPi-hole upsmon[9283]: Unable to use old-style MONITOR line wit May 21 09:30:38 SVPi-hole upsmon[9283]: Convert it and add a username to upsd.us May 21 09:30:38 SVPi-hole upsmon[9283]: Fatal error: unusable configuration May 21 09:30:38 SVPi-hole upsmon[9283]: Network UPS Tools upsmon 2.7.4 May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Control process exite May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Failed with result 'e May 21 09:30:38 SVPi-hole systemd[1]: Failed to start Network UPS Tools - power lines 1-15/15 (END)...skipping... ● nut-monitor.service - Network UPS Tools - power device monitor and shutdown controller Loaded: loaded (/lib/systemd/system/nut-monitor.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 09:30:38 CEST; 17s ago Process: 9283 ExecStart=/sbin/upsmon (code=exited, status=1/FAILURE) May 21 09:30:38 SVPi-hole systemd[1]: Starting Network UPS Tools - power device monitor and shutdown controller... May 21 09:30:38 SVPi-hole upsmon[9283]: fopen /var/run/nut/upsmon.pid: No such file or directory May 21 09:30:38 SVPi-hole upsmon[9283]: Using power down flag file /etc/killpower May 21 09:30:38 SVPi-hole upsmon[9283]: Unable to use old-style MONITOR line without a username May 21 09:30:38 SVPi-hole upsmon[9283]: Convert it and add a username to upsd.users - see the documentation May 21 09:30:38 SVPi-hole upsmon[9283]: Fatal error: unusable configuration May 21 09:30:38 SVPi-hole upsmon[9283]: Network UPS Tools upsmon 2.7.4 May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Control process exited, code=exited, status=1/FAILURE May 21 09:30:38 SVPi-hole systemd[1]: nut-monitor.service: Failed with result 'exit-code'. May 21 09:30:38 SVPi-hole systemd[1]: Failed to start Network UPS Tools - power device monitor and shutdown controller. ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ lines 1-15/15 (END)@ostseereiter sagte in USV:
Ja nun habe ich auf den Client das installiert und natürlich eingetragen in den beiden Dateien
was installiert und was eingetragen?
In den Clients muss natürlich was anderes in den config-Dateien stehen, als im Server
kein Support per PN! - Fragen im Forum stellen -
Benutzt das Voting rechts unten im Beitrag wenn er euch geholfen hat.
Das Forum freut sich über eine Spende. Benutzt dazu den Spendenbutton oben rechts. Danke!
der Installationsfixer: curl -fsL https://iobroker.net/fix.sh | bash - -
@ostseereiter sagte in USV:
Ja nun habe ich auf den Client das installiert und natürlich eingetragen in den beiden Dateien
was installiert und was eingetragen?
In den Clients muss natürlich was anderes in den config-Dateien stehen, als im Server
@homoran ja ich dokumentiere noch mal alles schritt für Schritt melde mich dann wieder.
-
So hier nochmal die einzelnen Schritte.
In der sudo nano /etc/nut/ups.conf
habe ich das eingetragen außer den pollinterval nicht.# # The general form is: # [serverups] driver = usbhid-ups port = auto desc = "Eeaton UPS" # # The section header ([upsname]) can be just about anything as long as # it is a single word inside brackets. upsd uses this to uniquely # identify a UPS on this system.in der sudo nano /etc/nut/nut.conf das
# IMPORTANT NOTE: # This file is intended to be sourced by shell scripts. # You MUST NOT use spaces around the equal sign! MODE=netservernun kommt sudo nano /etc/nut/upsd.conf da habe ich das drin
# you can specify if upsd requests or requires client's' certificates. # Possible values are : # - 0 to not request to clients to provide any certificate # - 1 to require to all clients a certificate # - 2 to require to all clients a valid certificate # # See 'docs/security.txt' or the Security chapter of NUT user manual # for more information on the SSL support in NUT. LISTEN 127.0.0.1 3493 LISTEN 192.168.178.109 3493nun die Benutzerkonten ich nehme gleich den 3 raus.sudo nano /etc/nut/upsd.users
# MONITOR myups@localhost 1 upsmon pass master (or slave) [upsmaster] password = test actions = SET instcmds = ALL upsmon master [raspiuser] password = secret upsmon slavein der sudo nano /etc/systemd/system/multi-user.target.wants/nut-server.service steht das:
Wants=nut-driver.service Before=nut-monitor.service [Service] ExecStartPre=/bin/sleep 30 ExecStart=/sbin/upsd Type=forking [Install] WantedBy=multi-user.targetJetzt das Monitoring sudo nano /etc/nut/upsmon.conf
da habe ich diese Zeile hinzugefügt:MONITOR serverups@localhost 1 upsmaster test masterDann habe ich den dienst neugestartet mit sudo systemctl restart nut-server
mitandy@debian:~$ sudo systemctl restart nut-serverDann kam dieses bei raus
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.Nun sollte der Server eingerichtet sein
Jetzt gehen wir zu den Client der Raspi
dort habe ich erst mal installiert mit sudo apt install nut-client
jetzt editiert mit sudo nano /etc/nut/nut.conf
dort steht drin# - netserver: same as for the standalone configuration, but also need # some more network access controls (firewall, tcp-wrappers) and possibly a # specific LISTEN directive in upsd.conf. # Since this MODE is opened to the network, a special care should be applied # to security concerns. # - netclient: this mode only requires upsmon. # # IMPORTANT NOTE: # This file is intended to be sourced by shell scripts. # You MUST NOT use spaces around the equal sign! MODE=netclientjetzt diese Datei sudo nano /etc/nut/upsmon.conf
When compiled with SSL, specify that a secured connection must be used # to communicate with upsd. # If you don't use 'CERTVERIFY 1', then this will at least make sure # that nobody can sniff your sessions without a large effort. Setting # this will make upsmon drop connections if the remote upsd doesn't # support SSL, so don't use it unless all of them have it running. # When compiled with NSS support of SSL, can be overriden for host # specified with a CERTHOST directive. MONITOR serverups@192.168.178.109 1 raspiuser testslavenun den Clientserver neu starten mit sudo systemctl restart nut-client
jetzt kommt diese Ausgabe.pi@SVPi-hole:~ $ sudo systemctl restart nut-client Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:03:50 2021): Communications with UPS serverups@192.168.178.109 lost Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:03:55 2021): UPS serverups@192.168.178.109 is unavailableund nach einer gewissen Zeit diese Ausgabe
pi@SVPi-hole:~ $ ^C Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:09:00 2021): UPS serverups@192.168.178.109 is unavailableGruß OSR
Plattform
Linux x64 CPUs2 AMD G-T56N Processor 1646 MHz 8GB RAM -
So hier nochmal die einzelnen Schritte.
In der sudo nano /etc/nut/ups.conf
habe ich das eingetragen außer den pollinterval nicht.# # The general form is: # [serverups] driver = usbhid-ups port = auto desc = "Eeaton UPS" # # The section header ([upsname]) can be just about anything as long as # it is a single word inside brackets. upsd uses this to uniquely # identify a UPS on this system.in der sudo nano /etc/nut/nut.conf das
# IMPORTANT NOTE: # This file is intended to be sourced by shell scripts. # You MUST NOT use spaces around the equal sign! MODE=netservernun kommt sudo nano /etc/nut/upsd.conf da habe ich das drin
# you can specify if upsd requests or requires client's' certificates. # Possible values are : # - 0 to not request to clients to provide any certificate # - 1 to require to all clients a certificate # - 2 to require to all clients a valid certificate # # See 'docs/security.txt' or the Security chapter of NUT user manual # for more information on the SSL support in NUT. LISTEN 127.0.0.1 3493 LISTEN 192.168.178.109 3493nun die Benutzerkonten ich nehme gleich den 3 raus.sudo nano /etc/nut/upsd.users
# MONITOR myups@localhost 1 upsmon pass master (or slave) [upsmaster] password = test actions = SET instcmds = ALL upsmon master [raspiuser] password = secret upsmon slavein der sudo nano /etc/systemd/system/multi-user.target.wants/nut-server.service steht das:
Wants=nut-driver.service Before=nut-monitor.service [Service] ExecStartPre=/bin/sleep 30 ExecStart=/sbin/upsd Type=forking [Install] WantedBy=multi-user.targetJetzt das Monitoring sudo nano /etc/nut/upsmon.conf
da habe ich diese Zeile hinzugefügt:MONITOR serverups@localhost 1 upsmaster test masterDann habe ich den dienst neugestartet mit sudo systemctl restart nut-server
mitandy@debian:~$ sudo systemctl restart nut-serverDann kam dieses bei raus
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.Nun sollte der Server eingerichtet sein
Jetzt gehen wir zu den Client der Raspi
dort habe ich erst mal installiert mit sudo apt install nut-client
jetzt editiert mit sudo nano /etc/nut/nut.conf
dort steht drin# - netserver: same as for the standalone configuration, but also need # some more network access controls (firewall, tcp-wrappers) and possibly a # specific LISTEN directive in upsd.conf. # Since this MODE is opened to the network, a special care should be applied # to security concerns. # - netclient: this mode only requires upsmon. # # IMPORTANT NOTE: # This file is intended to be sourced by shell scripts. # You MUST NOT use spaces around the equal sign! MODE=netclientjetzt diese Datei sudo nano /etc/nut/upsmon.conf
When compiled with SSL, specify that a secured connection must be used # to communicate with upsd. # If you don't use 'CERTVERIFY 1', then this will at least make sure # that nobody can sniff your sessions without a large effort. Setting # this will make upsmon drop connections if the remote upsd doesn't # support SSL, so don't use it unless all of them have it running. # When compiled with NSS support of SSL, can be overriden for host # specified with a CERTHOST directive. MONITOR serverups@192.168.178.109 1 raspiuser testslavenun den Clientserver neu starten mit sudo systemctl restart nut-client
jetzt kommt diese Ausgabe.pi@SVPi-hole:~ $ sudo systemctl restart nut-client Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:03:50 2021): Communications with UPS serverups@192.168.178.109 lost Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:03:55 2021): UPS serverups@192.168.178.109 is unavailableund nach einer gewissen Zeit diese Ausgabe
pi@SVPi-hole:~ $ ^C Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:09:00 2021): UPS serverups@192.168.178.109 is unavailable@ostseereiter sagte in USV:
In der sudo nano /etc/nut/ups.conf
habe ich das eingetragenBeim Server oder bei den Clients?
kein Support per PN! - Fragen im Forum stellen -
Benutzt das Voting rechts unten im Beitrag wenn er euch geholfen hat.
Das Forum freut sich über eine Spende. Benutzt dazu den Spendenbutton oben rechts. Danke!
der Installationsfixer: curl -fsL https://iobroker.net/fix.sh | bash - -
So hier nochmal die einzelnen Schritte.
In der sudo nano /etc/nut/ups.conf
habe ich das eingetragen außer den pollinterval nicht.# # The general form is: # [serverups] driver = usbhid-ups port = auto desc = "Eeaton UPS" # # The section header ([upsname]) can be just about anything as long as # it is a single word inside brackets. upsd uses this to uniquely # identify a UPS on this system.in der sudo nano /etc/nut/nut.conf das
# IMPORTANT NOTE: # This file is intended to be sourced by shell scripts. # You MUST NOT use spaces around the equal sign! MODE=netservernun kommt sudo nano /etc/nut/upsd.conf da habe ich das drin
# you can specify if upsd requests or requires client's' certificates. # Possible values are : # - 0 to not request to clients to provide any certificate # - 1 to require to all clients a certificate # - 2 to require to all clients a valid certificate # # See 'docs/security.txt' or the Security chapter of NUT user manual # for more information on the SSL support in NUT. LISTEN 127.0.0.1 3493 LISTEN 192.168.178.109 3493nun die Benutzerkonten ich nehme gleich den 3 raus.sudo nano /etc/nut/upsd.users
# MONITOR myups@localhost 1 upsmon pass master (or slave) [upsmaster] password = test actions = SET instcmds = ALL upsmon master [raspiuser] password = secret upsmon slavein der sudo nano /etc/systemd/system/multi-user.target.wants/nut-server.service steht das:
Wants=nut-driver.service Before=nut-monitor.service [Service] ExecStartPre=/bin/sleep 30 ExecStart=/sbin/upsd Type=forking [Install] WantedBy=multi-user.targetJetzt das Monitoring sudo nano /etc/nut/upsmon.conf
da habe ich diese Zeile hinzugefügt:MONITOR serverups@localhost 1 upsmaster test masterDann habe ich den dienst neugestartet mit sudo systemctl restart nut-server
mitandy@debian:~$ sudo systemctl restart nut-serverDann kam dieses bei raus
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.Nun sollte der Server eingerichtet sein
Jetzt gehen wir zu den Client der Raspi
dort habe ich erst mal installiert mit sudo apt install nut-client
jetzt editiert mit sudo nano /etc/nut/nut.conf
dort steht drin# - netserver: same as for the standalone configuration, but also need # some more network access controls (firewall, tcp-wrappers) and possibly a # specific LISTEN directive in upsd.conf. # Since this MODE is opened to the network, a special care should be applied # to security concerns. # - netclient: this mode only requires upsmon. # # IMPORTANT NOTE: # This file is intended to be sourced by shell scripts. # You MUST NOT use spaces around the equal sign! MODE=netclientjetzt diese Datei sudo nano /etc/nut/upsmon.conf
When compiled with SSL, specify that a secured connection must be used # to communicate with upsd. # If you don't use 'CERTVERIFY 1', then this will at least make sure # that nobody can sniff your sessions without a large effort. Setting # this will make upsmon drop connections if the remote upsd doesn't # support SSL, so don't use it unless all of them have it running. # When compiled with NSS support of SSL, can be overriden for host # specified with a CERTHOST directive. MONITOR serverups@192.168.178.109 1 raspiuser testslavenun den Clientserver neu starten mit sudo systemctl restart nut-client
jetzt kommt diese Ausgabe.pi@SVPi-hole:~ $ sudo systemctl restart nut-client Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:03:50 2021): Communications with UPS serverups@192.168.178.109 lost Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:03:55 2021): UPS serverups@192.168.178.109 is unavailableund nach einer gewissen Zeit diese Ausgabe
pi@SVPi-hole:~ $ ^C Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:09:00 2021): UPS serverups@192.168.178.109 is unavailable@ostseereiter sagte in USV:
Nun sollte der Server eingerichtet sein
aber das davor hast du schon gelesen?
@ostseereiter sagte in USV:
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.
und behoben?
wohl eher nicht!
denn der Controller schgeint weiter nicht erreichbar zu sein@ostseereiter sagte in USV:
UPS serverups@192.168.178.109 is unavailable
kein Support per PN! - Fragen im Forum stellen -
Benutzt das Voting rechts unten im Beitrag wenn er euch geholfen hat.
Das Forum freut sich über eine Spende. Benutzt dazu den Spendenbutton oben rechts. Danke!
der Installationsfixer: curl -fsL https://iobroker.net/fix.sh | bash - -
@ostseereiter sagte in USV:
In der sudo nano /etc/nut/ups.conf
habe ich das eingetragenBeim Server oder bei den Clients?
-
@homoran
im Server@ostseereiter
Ich lese da wieder pihole. Muss da ggf. auch noch was eingestellt werden? -
@ostseereiter sagte in USV:
Nun sollte der Server eingerichtet sein
aber das davor hast du schon gelesen?
@ostseereiter sagte in USV:
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.
und behoben?
wohl eher nicht!
denn der Controller schgeint weiter nicht erreichbar zu sein@ostseereiter sagte in USV:
UPS serverups@192.168.178.109 is unavailable
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.
und behoben?
wohl eher nicht!
denn der Controller schgeint weiter nicht erreichbar zu sein
@ostseereiter sagte in USV:jetzt habe ich versucht das zu beheben.
andy@debian:~$ sudo systemctl daemon-reload [sudo] Passwort für andy: andy@debian:~$ sudo systemctl restart nut-server Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details. andy@debian:~$ ^C andy@debian:~$ sudo systemctl status nut-server.service ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor prese Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ag Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices in Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is alre Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or u Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, c Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit- Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power dev lines 1-13/13 (END)...skipping... ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ago Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices information server... Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is already running! Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or use the 'reload' command. Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, code=exited, status=1/FAILURE Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit-code'. Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power devices information server. lines 1-13/13 (END) ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor prese Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ag Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices in Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is alre Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or u Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, c Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit- Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power dev lines 1-13/13 (END) ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ago Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices information server... Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is already running! Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or use the 'reload' command. Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, code=exited, status=1/FAILURE Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit-code'. Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power devices information server.Gruß OSR
Plattform
Linux x64 CPUs2 AMD G-T56N Processor 1646 MHz 8GB RAM -
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.
und behoben?
wohl eher nicht!
denn der Controller schgeint weiter nicht erreichbar zu sein
@ostseereiter sagte in USV:jetzt habe ich versucht das zu beheben.
andy@debian:~$ sudo systemctl daemon-reload [sudo] Passwort für andy: andy@debian:~$ sudo systemctl restart nut-server Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details. andy@debian:~$ ^C andy@debian:~$ sudo systemctl status nut-server.service ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor prese Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ag Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices in Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is alre Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or u Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, c Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit- Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power dev lines 1-13/13 (END)...skipping... ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ago Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices information server... Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is already running! Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or use the 'reload' command. Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, code=exited, status=1/FAILURE Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit-code'. Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power devices information server. lines 1-13/13 (END) ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor prese Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ag Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices in Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is alre Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or u Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, c Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit- Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power dev lines 1-13/13 (END) ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ago Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices information server... Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is already running! Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or use the 'reload' command. Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, code=exited, status=1/FAILURE Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit-code'. Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power devices information server.@ostseereiter sagte in USV:
jetzt habe ich versucht das zu beheben.
entscheidend ist vielmehr die Frage was du gemacht hast bevor/so dass es zu dieser Fehlermeldung kam:
@ostseereiter sagte in USV:
The unit file, source configuration file or drop-ins of nut-server.service changed on disk
was hast du da im System verstellt?
kein Support per PN! - Fragen im Forum stellen -
Benutzt das Voting rechts unten im Beitrag wenn er euch geholfen hat.
Das Forum freut sich über eine Spende. Benutzt dazu den Spendenbutton oben rechts. Danke!
der Installationsfixer: curl -fsL https://iobroker.net/fix.sh | bash - -
@ostseereiter sagte in USV:
jetzt habe ich versucht das zu beheben.
entscheidend ist vielmehr die Frage was du gemacht hast bevor/so dass es zu dieser Fehlermeldung kam:
@ostseereiter sagte in USV:
The unit file, source configuration file or drop-ins of nut-server.service changed on disk
was hast du da im System verstellt?
-
-
So hier nochmal die einzelnen Schritte.
In der sudo nano /etc/nut/ups.conf
habe ich das eingetragen außer den pollinterval nicht.# # The general form is: # [serverups] driver = usbhid-ups port = auto desc = "Eeaton UPS" # # The section header ([upsname]) can be just about anything as long as # it is a single word inside brackets. upsd uses this to uniquely # identify a UPS on this system.in der sudo nano /etc/nut/nut.conf das
# IMPORTANT NOTE: # This file is intended to be sourced by shell scripts. # You MUST NOT use spaces around the equal sign! MODE=netservernun kommt sudo nano /etc/nut/upsd.conf da habe ich das drin
# you can specify if upsd requests or requires client's' certificates. # Possible values are : # - 0 to not request to clients to provide any certificate # - 1 to require to all clients a certificate # - 2 to require to all clients a valid certificate # # See 'docs/security.txt' or the Security chapter of NUT user manual # for more information on the SSL support in NUT. LISTEN 127.0.0.1 3493 LISTEN 192.168.178.109 3493nun die Benutzerkonten ich nehme gleich den 3 raus.sudo nano /etc/nut/upsd.users
# MONITOR myups@localhost 1 upsmon pass master (or slave) [upsmaster] password = test actions = SET instcmds = ALL upsmon master [raspiuser] password = secret upsmon slavein der sudo nano /etc/systemd/system/multi-user.target.wants/nut-server.service steht das:
Wants=nut-driver.service Before=nut-monitor.service [Service] ExecStartPre=/bin/sleep 30 ExecStart=/sbin/upsd Type=forking [Install] WantedBy=multi-user.targetJetzt das Monitoring sudo nano /etc/nut/upsmon.conf
da habe ich diese Zeile hinzugefügt:MONITOR serverups@localhost 1 upsmaster test masterDann habe ich den dienst neugestartet mit sudo systemctl restart nut-server
mitandy@debian:~$ sudo systemctl restart nut-serverDann kam dieses bei raus
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.Nun sollte der Server eingerichtet sein
Jetzt gehen wir zu den Client der Raspi
dort habe ich erst mal installiert mit sudo apt install nut-client
jetzt editiert mit sudo nano /etc/nut/nut.conf
dort steht drin# - netserver: same as for the standalone configuration, but also need # some more network access controls (firewall, tcp-wrappers) and possibly a # specific LISTEN directive in upsd.conf. # Since this MODE is opened to the network, a special care should be applied # to security concerns. # - netclient: this mode only requires upsmon. # # IMPORTANT NOTE: # This file is intended to be sourced by shell scripts. # You MUST NOT use spaces around the equal sign! MODE=netclientjetzt diese Datei sudo nano /etc/nut/upsmon.conf
When compiled with SSL, specify that a secured connection must be used # to communicate with upsd. # If you don't use 'CERTVERIFY 1', then this will at least make sure # that nobody can sniff your sessions without a large effort. Setting # this will make upsmon drop connections if the remote upsd doesn't # support SSL, so don't use it unless all of them have it running. # When compiled with NSS support of SSL, can be overriden for host # specified with a CERTHOST directive. MONITOR serverups@192.168.178.109 1 raspiuser testslavenun den Clientserver neu starten mit sudo systemctl restart nut-client
jetzt kommt diese Ausgabe.pi@SVPi-hole:~ $ sudo systemctl restart nut-client Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:03:50 2021): Communications with UPS serverups@192.168.178.109 lost Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:03:55 2021): UPS serverups@192.168.178.109 is unavailableund nach einer gewissen Zeit diese Ausgabe
pi@SVPi-hole:~ $ ^C Broadcast message from nut@SVPi-hole (somewhere) (Fri May 21 11:09:00 2021): UPS serverups@192.168.178.109 is unavailable@ostseereiter sagte in USV:
[raspiuser]
password = secret
upsmon slavenano /etc/nut/upsmon.conf, der Eintrag ist ebenfalls falsch
MONITOR serverups@192.168.178.109 1 raspiuser testslave@ostseereiter sagte in USV:
Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is alre
du bekommst deinen service nicht zum laufen, hatte ich damals auch diese Meldung, als ich beim ersten mal die config falsch eingestellt hatte. Selbst als die Config dann richtig war, kam diese Meldung.
Lösung war bei mir letztendlich, das ich den (Nut- server und nut - client) nochmal de/installiert habe, anschliessend die config der Reihe nach eingestellt habe und lief dann. -
ja und das heißt ? Ich bin total überfordert im moment.Nicht böse sein wegen meiner Dummheit
Gruß OSR
Plattform
Linux x64 CPUs2 AMD G-T56N Processor 1646 MHz 8GB RAM -
ja und das heißt ? Ich bin total überfordert im moment.Nicht böse sein wegen meiner Dummheit
andy@debian:~$ sudo upsd Network UPS Tools upsd 2.7.4 fopen /var/run/nut/upsd.pid: No such file or directory listening on 192.168.178.109 port 3493 listening on 127.0.0.1 port 3493 Can't connect to UPS [serverups] (usbhid-ups-serverups): No such file or directory andy@debian:~$Gruß OSR
Plattform
Linux x64 CPUs2 AMD G-T56N Processor 1646 MHz 8GB RAM -
Warning: The unit file, source configuration file or drop-ins of nut-server.service changed on disk. Run 'systemctl daemon-reload' to reload units. Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details.
und behoben?
wohl eher nicht!
denn der Controller schgeint weiter nicht erreichbar zu sein
@ostseereiter sagte in USV:jetzt habe ich versucht das zu beheben.
andy@debian:~$ sudo systemctl daemon-reload [sudo] Passwort für andy: andy@debian:~$ sudo systemctl restart nut-server Job for nut-server.service failed because the control process exited with error code. See "systemctl status nut-server.service" and "journalctl -xe" for details. andy@debian:~$ ^C andy@debian:~$ sudo systemctl status nut-server.service ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor prese Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ag Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices in Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is alre Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or u Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, c Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit- Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power dev lines 1-13/13 (END)...skipping... ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ago Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices information server... Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is already running! Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or use the 'reload' command. Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, code=exited, status=1/FAILURE Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit-code'. Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power devices information server. lines 1-13/13 (END) ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor prese Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ag Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices in Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is alre Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or u Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, c Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit- Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power dev lines 1-13/13 (END) ● nut-server.service - Network UPS Tools - power devices information server Loaded: loaded (/lib/systemd/system/nut-server.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-05-21 12:11:20 CEST; 45s ago Process: 1409 ExecStartPre=/bin/sleep 30 (code=exited, status=0/SUCCESS) Process: 2130 ExecStart=/sbin/upsd (code=exited, status=1/FAILURE) Mai 21 12:10:50 debian systemd[1]: Starting Network UPS Tools - power devices information server... Mai 21 12:11:20 debian upsd[2130]: Network UPS Tools upsd 2.7.4 Mai 21 12:11:20 debian upsd[2130]: Fatal error: A previous upsd instance is already running! Mai 21 12:11:20 debian upsd[2130]: Either stop the previous instance first, or use the 'reload' command. Mai 21 12:11:20 debian systemd[1]: nut-server.service: Control process exited, code=exited, status=1/FAILURE Mai 21 12:11:20 debian systemd[1]: nut-server.service: Failed with result 'exit-code'. Mai 21 12:11:20 debian systemd[1]: Failed to start Network UPS Tools - power devices information server.
Hey! Du scheinst an dieser Unterhaltung interessiert zu sein, hast aber noch kein Konto.
Hast du es satt, bei jedem Besuch durch die gleichen Beiträge zu scrollen? Wenn du dich für ein Konto anmeldest, kommst du immer genau dorthin zurück, wo du zuvor warst, und kannst dich über neue Antworten benachrichtigen lassen (entweder per E-Mail oder Push-Benachrichtigung). Du kannst auch Lesezeichen speichern und Beiträge positiv bewerten, um anderen Community-Mitgliedern deine Wertschätzung zu zeigen.
Mit deinem Input könnte dieser Beitrag noch besser werden 💗
Registrieren Anmelden513
Online32.8k
Benutzer82.8k
Themen1.3m
Beiträge