Jahresrückblick 2025 – unser neuer Blogbeitrag ist online! ✨

[wibear]

Hallo Forum, brauche dringend eure Hilfe.
Ich betreibe IOBroker und pivCCU auf einem RPi 4. Nach einem Versuch node.js upzudaten mit diesen Befehlen:
curl -sL https://deb.nodesource.com/setup_20.x | sudo -E bash -
sudo apt-get install -y nodejs
reboot
iobroker fix
startet pivCCU nicht mehr, auch nach mehreren reboots.

Wie man sieht, zeigt auch info einen Fehler.
Es werden permanent neue Logs geschrieben:

Was ist da schief gelaufen und wie kann ich es jetzt beheben?
Danke Euch im Voraus und Grüße

[Homoran]

@wibear Ich schieb das mal von "Forum" nach "allgemein"

[wibear]

@homoran Danke, sorry, war zu schnell

[Homoran]

@wibear sagte in pivCCU nach Update node.js nicht erreichbar:

Es werden permanent neue Logs geschrieben:

bitte als Text in code-tags!

Hast du zu deiner Installation noch was zu sagen?
https://forum.iobroker.net/topic/51555/hinweise-für-gute-forenbeiträge/1

[Thomas Braun]

@wibear sagte in pivCCU nach Update node.js nicht erreichbar:

Was ist da schief gelaufen und wie kann ich es jetzt beheben?

Keine Ahnung was da nun Phase ist.
Schau dir

iob diag

an. In der Langfassung.

[wibear]

@homoran sagte in pivCCU nach Update node.js nicht erreichbar:

bitte als Text in code-tags!

Die IP von pivCCU ist 192.168.178.12.

Init not possible, going to stop: connect EHOSTUNREACH 192.168.178.12:2001
Cannot call init: [http://192.168.178.10:12001, ""] connect EHOSTUNREACH 192.168.178.12:2001
CCU 192.168.178.12 unreachable
setTimeout called, but adapter is shutting down

Bitte welche Daten zu meinem System fehlen noch?

PlatformBetriebssystem:linux
Architektur:arm
CPUs:4
Geschwindigkeit:1800 MHz
Modell:unknown
RAM:3.7 GB
System-Betriebszeit:00:04:27
Node.js:v18.18.0
time:1723555212199
timeOffset:-120
NPM:10.8.2
Adapter-Anzahl:540
Datenträgergröße:28.9 GB
Freier Festplattenspeicher:18.3 GB
Aktive Instanzen:20
Pfad:/opt/iobroker/
Betriebszeit:00:04:02
aktiv:true
_nodeCurrent:18.18.0
_nodeNewest:18.20.4
_nodeNewestNext:20.16.0
_npmCurrent:10.8.2
_npmNewest:9.8.1
_npmNewestNext:10.8.1

[Thomas Braun]

@wibear sagte in pivCCU nach Update node.js nicht erreichbar:

Node.js:v18.18.0

Da ist also schon was in die Hose gegangen, wenn du 20 installieren wolltest...

iob nodejs-update 20

und anschließend

iob diag

[wibear]

@thomas-braun

iob diag

Model : Raspberry Pi 4 Model B Rev 1.5
Docker : false
Virtualization : none
Kernel : armv7l
Userland : 32 bit

Systemuptime and Load:
15:51:21 up 35 min, 1 user, load average: 1.13, 0.75, 2.22
CPU threads: 4

Copy text starting here:

======================= SUMMARY =======================
                        v.2024-05-22


*** RASPBERRY THROTTLING ***
Current issues:
No throttling issues detected.

Previously detected issues:
No throttling issues detected.

*** Time and Time Zones ***
               Local time: Tue 2024-08-13 15:51:21 CEST
           Universal time: Tue 2024-08-13 13:51:21 UTC
                 RTC time: n/a
                Time zone: Europe/Berlin (CEST, +0200)
System clock synchronized: yes
              NTP service: active
          RTC in local TZ: no

*** Users and Groups ***
User that called 'iob diag':
wibear
HOME=/home/wibear
GROUPS=wibear adm dialout cdrom sudo audio video plugdev games users input render netdev gpio i2c spi iobroker

User that is running 'js-controller':
iobroker
HOME=/home/iobroker
GROUPS=iobroker tty dialout audio video plugdev bluetooth gpio i2c

*** Display-Server-Setup ***
Display-Server: false
Desktop:
Terminal:       tty
Boot Target:    multi-user.target

*** MEMORY ***
               total        used        free      shared  buff/cache   available
Mem:            3.9G        1.1G        2.2G        1.0M        568M        2.6G
Swap:            99M          0B         99M
Total:          4.0G        1.1G        2.3G

Active iob-Instances:   20

         3885 M total memory
         1134 M used memory
          179 M active memory
         1411 M inactive memory
         2182 M free memory
           64 M buffer memory
          504 M swap cache
           99 M total swap
            0 M used swap
           99 M free swap

*** top - Table Of Processes  ***
top - 15:51:22 up 35 min,  1 user,  load average: 1.13, 0.75, 2.22
Tasks: 219 total,   3 running, 216 sleeping,   0 stopped,   0 zombie
%Cpu(s): 25.8 us,  9.7 sy,  0.0 ni, 54.8 id,  6.5 wa,  0.0 hi,  3.2 si,  0.0 st
MiB Mem :   3885.9 total,   2184.1 free,   1132.9 used,    568.8 buff/cache
MiB Swap:    100.0 total,    100.0 free,      0.0 used.   2635.5 avail Mem

*** FAILED SERVICES ***

  UNIT                       LOAD   ACTIVE SUB    DESCRIPTION
* pivccu-dkms.service        loaded failed failed piVCCU DKMS Modules
* pivccu-rpi-modules.service loaded failed failed piVCCU RPi Kernel loader

LOAD   = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB    = The low-level unit activation state, values depend on unit type.
2 loaded units listed.

*** FILESYSTEM ***
Filesystem     Type      Size  Used Avail Use% Mounted on
/dev/root      ext4       29G   11G   18G  39% /
devtmpfs       devtmpfs  1.7G     0  1.7G   0% /dev
tmpfs          tmpfs     1.9G     0  1.9G   0% /dev/shm
tmpfs          tmpfs     778M  1.1M  777M   1% /run
tmpfs          tmpfs     5.0M  4.0K  5.0M   1% /run/lock
/dev/mmcblk0p1 vfat      255M   63M  193M  25% /boot
tmpfs          tmpfs     389M     0  389M   0% /run/user/1000

Messages concerning ext4 filesystem in dmesg:
[Tue Aug 13 15:15:44 2024] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 snd_bcm2835.enable_headphones=1 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_hdmi=0  smsc95xx.macaddr=D8:3A:DD:16:18:C4 vc_mem.mem_base=0x3f000000 vc_mem.mem_size=0x3f600000  console=tty1 root=PARTUUID=e605bf32-02 rootfstype=ext4 fsck.repair=yes rootwait
[Tue Aug 13 15:15:45 2024] EXT4-fs (mmcblk0p2): mounted filesystem d3104e7d-5f59-47e0-8621-290882475163 ro with ordered data mode. Quota mode: none.
[Tue Aug 13 15:15:45 2024] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[Tue Aug 13 15:15:46 2024] EXT4-fs (mmcblk0p2): re-mounted d3104e7d-5f59-47e0-8621-290882475163 r/w. Quot   Static hostname: iobroker-pi
         Icon name: computer
  Operating System: Raspbian GNU/Linux 11 (bullseye)
            Kernel: Linux 6.6.44-v7l+
      Architecture: arm

Installation:           native
Kernel:                 armv7l
Userland:               32 bit
Timezone:               Europe/Berlin (CEST, +0200)
User-ID:                1000
Display-Server:         false
Boot Target:            multi-user.target

Pending OS-Updates:     0
Pending iob updates:    1

Nodejs-Installation:
/usr/bin/nodejs         v20.16.0
/usr/local/bin/node             v18.18.0
/usr/local/bin/npm              10.8.2
/usr/local/bin/npx              10.8.2
/usr/local/bin/corepack         0.19.0

Recommended versions are nodejs 20.16.0 and npm 10.8.1
*** nodejs is NOT correctly installed ***
Wrong installation path detected. This needs to be fixed.

Please execute
iobroker nodejs-update
to fix these errors.

MEMORY:
               total        used        free      shared  buff/cache   available
Mem:            3.9G        1.2G        2.0G        1.0M        649M        2.5G
Swap:            99M          0B         99M
Total:          4.0G        1.2G        2.1G

Active iob-Instances:   20
Active repo(s): stable

ioBroker Core:          js-controller           5.0.19
                        admin                   7.0.22

ioBroker Status:        iobroker is running on this host.


Objects type: jsonl
States  type: jsonl

Status admin and web instance:
+ system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
+ system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin

Objects:                7401
States:                 6256

Size of iob-Database:

15M     /opt/iobroker/iobroker-data/objects.jsonl
9.0M    /opt/iobroker/iobroker-data/states.jsonl



=================== END OF SUMMARY ====================

=== Mark text until here for copying ===

wibear@iobroker-pi:~ $ ======== Start marking the full check here =========
-bash: ========: command not found
wibear@iobroker-pi:~ $
wibear@iobroker-pi:~ $ 
> Skript v.2024-05-22
>
> *** BASE SYSTEM ***
>    Static hostname: iobroker-pi
>          Icon name: computer
>   Operating System: Raspbian GNU/Linux 11 (bullseye)
>             Kernel: Linux 6.6.44-v7l+
>       Architecture: arm
>
> Model           : Raspberry Pi 4 Model B Rev 1.5
> Docker          : false
> Virtualization  : none
> Kernel          : armv7l
> Userland        : 32 bit
>
> Systemuptime and Load:
>  15:51:21 up 35 min,  1 user,  load average: 1.13, 0.75, 2.22
> CPU threads: 4
>
>
> *** RASPBERRY THROTTLING ***
> Current issues:
> No throttling issues detected.
>
> Previously detected issues:
> No throttling issues detected.
>
> *** Time and Time Zones ***
>                Local time: Tue 2024-08-13 15:51:21 CEST
>            Universal time: Tue 2024-08-13 13:51:21 UTC
>                  RTC time: n/a
/>                 Time zone: Europe/Berlin (CEST, +0200)
> System clock synchronized: yes
>               NTP service: active
>           RTC in local TZ: no
>
> *** Users and Groups ***
> User that called 'iob diag':
> wibear
> HOME=/home/wibear
> GROUPS=wibear adm dialout cdrom sudo audio video plugdev games users input render netdev gpio i2c spi iobroker
>
> User that is running 'js-controller':
> iobroker
> HOME=/home/iobroker
> GROUPS=iobroker tty dialout audio video plugdev bluetooth gpio i2c
>
> *** Display-Server-Setup ***
> Display-Server: false
> Desktop:
> Terminal:       tty
> Boot Target:    multi-user.target
>
> *** MEMORY ***
>                total        used        free      shared  buff/cache   available
> Mem:            3.9G        1.1G        2.2G        1.0M        568M        2.6G
> Swap:            99M          0B         99M
> Total:          4.0G        1.1G        2.3G
>
> Active iob-Instances:   20
>
>          3885 M total memory
>          1134 M used memory
>           179 M active memory
>          1411 M inactive memory
>          2182 M free memory
>            64 M buffer memory
>           504 M swap cache
>            99 M total swap
>             0 M used swap
>            99 M free swap
>
> *** top - Table Of Processes  ***
> top - 15:51:22 up 35 min,  1 user,  load average: 1.13, 0.75, 2.22
> Tasks: 219 total,   3 running, 216 sleeping,   0 stopped,   0 zombie
> %Cpu(s): 25.8 us,  9.7 sy,  0.0 ni, 54.8 id,  6.5 wa,  0.0 hi,  3.2 si,  0.0 st
> MiB Mem :   3885.9 total,   2184.1 free,   1132.9 used,    568.8 buff/cache
> MiB Swap:    100.0 total,    100.0 free,      0.0 used.   2635.5 avail Mem
>
> *** FAILED SERVICES ***
>
>   UNIT                       LOAD   ACTIVE SUB    DESCRIPTION
> * pivccu-dkms.service        loaded failed failed piVCCU DKMS Modules
> * pivccu-rpi-modules.service loaded failed failed piVCCU RPi Kernel loader
>
> LOAD   = Reflects whether the unit definition was properly loaded.
> ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
> SUB    = The low-level unit activation state, values depend on unit type.
> 2 loaded units listed.
>
> *** FILESYSTEM ***
> Filesystem     Type      Size  Used Avail Use% Mounted on
> /dev/root      ext4       29G   11G   18G  39% /
> devtmpfs       devtmpfs  1.7G     0  1.7G   0% /dev
> tmpfs          tmpfs     1.9G     0  1.9G   0% /dev/shm
> tmpfs          tmpfs     778M  1.1M  777M   1% /run
> tmpfs          tmpfs     5.0M  4.0K  5.0M   1% /run/lock
> /dev/mmcblk0p1 vfat      255M   63M  193M  25% /boot
> tmpfs          tmpfs     389M     0  389M   0% /run/user/1000
>
> Messages concerning ext4 filesystem in dmesg:
> [Tue Aug 13 15:15:44 2024] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 snd_bcm2835.enable_headphones=1 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_hdmi=0  smsc95xx.macaddr=D8:3A:DD:16:18:C4 vc_mem.mem_base=0x3f000000 vc_mem.mem_size=0x3f600000  console=tty1 root=PARTUUID=e605bf32-02 rootfstype=ext4 fsck.repair=yes rootwait
> [Tue Aug 13 15:15:45 2024] EXT4-fs (mmcblk0p2): mounted filesystem d3104e7d-5f59-47e0-8621-290882475163 ro with ordered data mode. Quota mode: none.
> [Tue Aug 13 15:15:45 2024] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
> [Tue Aug 13 15:15:46 2024] EXT4-fs (mmcblk0p2): re-mounted d3104e7d-5f59-47e0-8621-290882475163 r/w. Quota mode: none.
>
> Show mounted filesystems:
> TARGET                       SOURCE         FSTYPE     OPTIONS
> /                            /dev/mmcblk0p2 ext4       rw,noatime
> |-/dev                       devtmpfs       devtmpfs   rw,relatime,size=1726396k,nr_inodes=34271,mode=755
> | |-/dev/shm                 tmpfs          tmpfs      rw,nosuid,nodev
> | |-/dev/pts                 devpts         devpts     rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000
> | `-/dev/mqueue              mqueue         mqueue     rw,nosuid,nodev,noexec,relatime
-bash: Skript: command not found
-bash: node_modules: command not found
-bash: Static: command not found
-bash: Icon: command not found
-bash: command substitution: line 7: syntax error near unexpected token `('
-bash: command substitution: line 7: `  Operating System: Raspbian GNU/Linux 11 (bullseye)'
-bash: -/dev/mqueue: No such file or directory
wibear@iobroker-pi:~ $ |-/proc                      proc           proc       rw,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | `-/proc/sys/fs/binfmt_misc systemd-1      autofs     rw,relatime,fd=30,pgrp=1,timeout=0,minproto=5,maxproto=5,direct
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ |-/sys                       sysfs          sysfs      rw,nosuid,nodev,noexec,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/sys/kernel/security     securityfs     securityfs rw,nosuid,nodev,noexec,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/sys/fs/cgroup           cgroup2        cgroup2    rw,nosuid,nodev,noexec,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/sys/fs/pstore           pstore         pstore     rw,nosuid,nodev,noexec,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/sys/fs/bpf              bpf            bpf        rw,nosuid,nodev,noexec,relatime,mode=700
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/sys/kernel/tracing      tracefs        tracefs    rw,nosuid,nodev,noexec,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/sys/kernel/debug        debugfs        debugfs    rw,nosuid,nodev,noexec,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/sys/fs/fuse/connections fusectl        fusectl    rw,nosuid,nodev,noexec,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | `-/sys/kernel/config       configfs       configfs   rw,nosuid,nodev,noexec,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ |-/run                       tmpfs          tmpfs      rw,nosuid,nodev,size=795828k,nr_inodes=819200,mode=755
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/run/lock                tmpfs          tmpfs      rw,nosuid,nodev,noexec,relatime,size=5120k
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | |-/run/rpc_pipefs          sunrpc         rpc_pipefs rw,relatime
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ | `-/run/user/1000           tmpfs          tmpfs      rw,nosuid,nodev,relatime,size=397912k,nr_inodes=99478,mode=700,uid=1000,gid=1000
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ |-/boot                      /dev/mmcblk0p1 vfat       rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=ascii,shortname=mixed,errors=remount-ro
-bash: syntax error near unexpected token `|'
wibear@iobroker-pi:~ $ `-/var/lib/lxcfs             lxcfs          fuse.lxcfs rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other
>
> Files in neuralgic directories:
>
> /var:
> du: cannot access '/var/lib/lxcfs/cgroup': Input/output error
> 4.6G    /var/
> 3.3G    /var/log
> 2.9G    /var/log/journal/6462312882a642219bbda7aff5f4f5b9
> 2.9G    /var/log/journal
> 729M    /var/lib
>
> Archived and active journals take up 2.8G in the file system.
>
> /opt/iobroker/backups:
> 82M     /opt/iobroker/backups/
>
> /opt/iobroker/iobroker-data:
> 747M    /opt/iobroker/iobroker-data/
> 594M    /opt/iobroker/iobroker-data/files
> 441M    /opt/iobroker/iobroker-data/files/javascript.admin
> 409M    /opt/iobroker/iobroker-data/files/javascript.admin/static
> 408M    /opt/iobroker/iobroker-data/files/javascript.admin/static/js
>
> The five largest files in iobroker-data are:
> 27M     /opt/iobroker/iobroker-data/files/backitup.admin/static/js/main.ce422ec2.js.map
> 24M     /opt/iobroker/iobroker-data/files/web.admin/static/js/main.135279a0.js.map
> 15M     /opt/iobroker/iobroker-data/objects.jsonl
> 8.7M    /opt/iobroker/iobroker-data/states.jsonl
> 8.7M    /opt/iobroker/iobroker-data/files/javascript.admin/static/js/838.0aa41cb0.chunk.js.map
>
> USB-Devices by-id:
> USB-Sticks -  Avoid direct links to /dev/tty* in your adapter setups, please always prefer the links 'by-id':
>
> No Devices found 'by-id'
>
>
>
>
> *** NodeJS-Installation ***
>
> /usr/bin/nodejs         v20.16.0
> /usr/local/bin/node             v18.18.0
> /usr/local/bin/npm              10.8.2
0        : device-reminder > /usr/local/bin/npx              10.8.2
> /usr/local/bin/corepack         0.19.0
> *** nodejs is NOT correctly installed ***
>
> nodejs:
>   Installed: 20.16.0-1nodesource1
>   Candidate: 20.16.0-1nodesource1
>   Version table:
>  *** 20.16.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>         100 /var/lib/dpkg/status
>      20.15.1-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.15.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.14.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.13.1-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.13.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.12.2-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.12.1-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.12.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.11.1-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.11.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.10.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.9.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.8.1-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.8.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.7.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.6.1-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.6.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.5.1-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.5.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.4.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.3.1-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.3.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.2.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.1.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      20.0.0-1nodesource1 600
>         500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
>      12.22.12~dfsg-1~deb11u4 500
>         500 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf Packages
>
> Temp directories causing npm8 problem: 0
> No problems detected
>
> Errors in npm tree:
>
> *** ioBroker-Installation ***
>
> ioBroker Status
> iobroker is running on this host.
>
>
> Objects type: jsonl
> States  type: jsonl
>
> Core adapters versions
> js-controller:  5.0.19
> admin:          7.0.22
> javascript:     8.7.6
>
> nodejs modules from github:     1
> +-- iobroker.vw-connect@0.5.3 (git+ssh://git@github.com/TA2k/ioBroker.vw-connect.git#b5fbfb41f65b8a1efb646e9efb68f1cbd1627d27)
>
> Adapter State
> + system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
> + system.adapter.alexa2.0                 : alexa2                : iobroker-pi                              -  enabled
> + system.adapter.backitup.0               : backitup              : iobroker-pi                              -  enabled
> + system.adapter.device-reminder.0        : device-reminder       : iobroker-pi                              -  enabled
> + system.adapter.discovery.0              : discovery             : iobroker-pi                              -  enabled
> + system.adapter.ems-esp.0                : ems-esp               : iobroker-pi                              -  enabled
> + system.adapter.fb-checkpresence.0       : fb-checkpresence      : iobroker-pi                              -  enabled
>   system.adapter.habpanel.0               : habpanel              : iobroker-pi                              -  enabled
> + system.adapter.history.0                : history               : iobroker-pi                              -  enabled
> + system.adapter.hm-rega.0                : hm-rega               : iobroker-pi                              -  enabled
>   system.adapter.hm-rpc.0                 : hm-rpc                : iobroker-pi                              -  enabled, port: 18701
>   system.adapter.hm-rpc.1                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12001
>   system.adapter.hm-rpc.2                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12010
> + system.adapter.influxdb.0               : influxdb              : iobroker-pi                              -  enabled, port: 8086
>   system.adapter.info.0                   : info                  : iobroker-pi                              -  enabled
> + system.adapter.javascript.0             : javascript            : iobroker-pi                              -  enabled
> + system.adapter.mqtt.0                   : mqtt                  : iobroker-pi                              -  enabled, port: 1883, bind: 192.168.178.10
>   system.adapter.netatmo-crawler.0        : netatmo-crawler       : iobroker-pi                              -  enabled
> + system.adapter.rpi2.0                   : rpi2                  : iobroker-pi                              -  enabled
> + system.adapter.shelly.0                 : shelly                : iobroker-pi                              -  enabled, port: 1882, bind: 0.0.0.0
> + system.adapter.simple-api.0             : simple-api            : iobroker-pi                              -  enabled, port: 8087, bind: 0.0.0.0, run as: admin
> + system.adapter.tr-064.0                 : tr-064                : iobroker-pi                              -  enabled
>   system.adapter.tuya.0                   : tuya                  : iobroker-pi                              - disabled
> + system.adapter.vw-connect.0             : vw-connect            : iobroker-pi                              -  enabled
>   system.adapter.weatherunderground.0     : weatherunderground    : iobroker-pi                              - disabled
> + system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin
> + system.adapter.whatsapp-cmb.0           : whatsapp-cmb          : iobroker-pi                              -  enabled
>
> + instance is alive
>
> Enabled adapters with bindings
> + system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
>   system.adapter.hm-rpc.0                 : hm-rpc                : iobroker-pi                              -  enabled, port: 18701
>   system.adapter.hm-rpc.1                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12001
>   system.adapter.hm-rpc.2                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12010
> + system.adapter.influxdb.0               : influxdb              : iobroker-pi                              -  enabled, port: 8086
> + system.adapter.mqtt.0                   : mqtt                  : iobroker-pi                              -  enabled, port: 1883, bind: 192.168.178.10
> + system.adapter.shelly.0                 : shelly                : iobroker-pi                              -  enabled, port: 1882, bind: 0.0.0.0
> + system.adapter.simple-api.0             : simple-api            : iobroker-pi                              -  enabled, port: 8087, bind: 0.0.0.0, run as: admin
> + system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin
>
> ioBroker-Repositories
> stable        : http://download.iobroker.net/sources-dist.json
> beta          : http://download.iobroker.net/sources-dist-latest.json
>
> Active repo(s): stable
>
> Installed ioBroker-Instances
> Used repository: stable
> Adapter    "admin"        : 7.0.22   , installed 7.0.22
> Adapter    "alexa2"       : 3.26.5   , installed 3.26.5
> Adapter    "backitup"     : 3.0.16   , installed 3.0.16
> Adapter    "device-reminder": 3.1.2  , installed 3.1.2
> Adapter    "discovery"    : 4.5.0    , installed 4.5.0
> Adapter    "ems-esp"      : 3.5.0    , installed 3.5.0
> Adapter    "fb-checkpresence": 1.2.4 , installed 1.2.4
> Adapter    "habpanel"     : 0.5.0    , installed 0.5.0
> Adapter    "history"      : 3.0.1    , installed 3.0.1
> Adapter    "hm-rega"      : 4.0.0    , installed 4.0.0
> Adapter    "hm-rpc"       : 1.17.0   , installed 1.17.0
> Adapter    "influxdb"     : 4.0.2    , installed 4.0.2
> Adapter    "javascript"   : 8.7.6    , installed 8.7.6
> Controller "js-controller": 6.0.9    , installed 5.0.19 [Updatable]
> Adapter    "mqtt"         : 5.2.0    , installed 5.2.0
> Adapter    "netatmo-crawler": 0.8.1  , installed 0.8.1
> Adapter    "rpi2"         : 1.3.2    , installed 1.3.2
> Adapter    "shelly"       : 7.0.0    , installed 7.0.0
> Adapter    "simple-api"   : 2.8.0    , installed 2.8.0
> Adapter    "socketio"     : 6.7.1    , installed 6.7.1
> Adapter    "tr-064"       : 4.3.0    , installed 4.3.0
> Adapter    "tuya"         : 3.15.0   , installed 3.15.0
> Adapter    "weatherunderground": 3.7.0, installed 3.7.0
> Adapter    "web"          : 6.2.5    , installed 6.2.5
> Adapter    "whatsapp-cmb" : 0.3.0    , installed 0.3.0
> Adapter    "ws"           : 2.6.2    , installed 2.6.2
>
> Objects and States
> Please stand by - This may take a while
> Objects:        7401
> States:         6256
>
> *** OS-Repositories and Updates ***
> Hit:1 https://repos.influxdata.com/debian bullseye InRelease
> Hit:2 http://raspbian.raspberrypi.org/raspbian bullseye InRelease
> Hit:3 http://archive.raspberrypi.org/debian bullseye InRelease
> Hit:4 https://deb.nodesource.com/node_20.x nodistro InRelease
> Hit:5 https://packages.grafana.com/oss/deb stable InRelease
> Hit:6 https://apt.pivccu.de/piVCCU stable InRelease
> Reading package lists...
> Pending Updates: 0
>
> *** Listening Ports ***
> Active Internet connections (only servers)
> Proto Recv-Q Send-Q Local Address           Foreign Address         State       User       Inode      PID/Program name
> tcp        0      0 127.0.0.1:8088          0.0.0.0:*               LISTEN      999        6286       745/influxd
> tcp        0      0 0.0.0.0:1882            0.0.0.0:*               LISTEN      1001       8815       1209/io.shelly.0
> tcp        0      0 127.0.0.1:9000          0.0.0.0:*               LISTEN      1001       6351       884/iobroker.js-con
> tcp        0      0 127.0.0.1:9001          0.0.0.0:*               LISTEN      1001       5758       884/iobroker.js-con
> tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN      0          4770       787/sshd: /usr/sbin
> tcp        0      0 192.168.178.10:1883     0.0.0.0:*               LISTEN      1001       6997       1170/io.mqtt.0
> tcp        0      0 10.0.3.1:53             0.0.0.0:*               LISTEN      0          4793       814/dnsmasq
> tcp6       0      0 :::8086                 :::*                    LISTEN      999        4863       745/influxd
> tcp6       0      0 :::8087                 :::*                    LISTEN      1001       9583       1272/io.simple-api.
> tcp6       0      0 :::8082                 :::*                    LISTEN      1001       8850       1314/io.web.0
> tcp6       0      0 :::8081                 :::*                    LISTEN      1001       5806       951/io.admin.0
> tcp6       0      0 :::3000                 :::*                    LISTEN      111        5756       883/grafana
48



============ Mark until here for C&P =============
> tcp6       0      0 :::22                   :::*                    LISTEN      0          4772       787/sshd: /usr/sbin
> udp        0      0 0.0.0.0:5353            0.0.0.0:*                           108        5445       372/avahi-daemon: r
> udp        0      0 0.0.0.0:55700           0.0.0.0:*                           108        5447       372/avahi-daemon: r
> udp        0      0 10.0.3.1:53             0.0.0.0:*                           0          4792       814/dnsmasq
> udp        0      0 0.0.0.0:67              0.0.0.0:*                           0          4789       814/dnsmasq
> udp        0      0 0.0.0.0:68              0.0.0.0:*                           0          4602       596/dhclient
> udp6       0      0 :::5353                 :::*                                108        5446       372/avahi-daemon: r
> udp6       0      0 :::48974                :::*                                108        5448       372/avahi-daemon: r
>
> *** Log File - Last 25 Lines ***
>
> 2024-08-13 15:51:30.782  - info: hm-rpc.2 (6575) xmlrpc client is trying to connect to 192.168.178.12:2010/ with ["http://192.168.178.10:12010","iobroker-pi:hm-rpc.2:325a5da9b9959b38a1d02500f5dff733"]
> 2024-08-13 15:51:30.849  - info: hm-rpc.1 (6586) xmlrpc server is trying to listen on 192.168.178.10:12001
> 2024-08-13 15:51:30.850  - info: hm-rpc.1 (6586) xmlrpc client is trying to connect to 192.168.178.12:2001/ with ["http://192.168.178.10:12001","iobroker-pi:hm-rpc.1:77e7296879feb3366411ef62aab861bd"]
> 2024-08-13 15:51:33.949  - error: hm-rpc.2 (6575) Init not possible, going to stop: connect EHOSTUNREACH 192.168.178.12:2010
> 2024-08-13 15:51:33.957  - error: hm-rpc.1 (6586) Init not possible, going to stop: connect EHOSTUNREACH 192.168.178.12:2001
> 2024-08-13 15:51:49.143  - info: hm-rpc.0 (6422) binrpc -> 192.168.178.12:8701/ init ["xmlrpc_bin://192.168.178.10:18701",""]
> 2024-08-13 15:51:49.160  - error: hm-rpc.0 (6422) Cannot call init: [xmlrpc_bin://192.168.178.10:18701, ""] Socket closed before the connection was established
> 2024-08-13 15:51:49.232  - info: hm-rpc.0 (6422) terminating
> 2024-08-13 15:51:49.234  - info: hm-rpc.0 (6422) Terminated (NO_ERROR): Without reason
> 2024-08-13 15:51:49.835  - info: host.iobroker-pi instance system.adapter.hm-rpc.0 terminated with code 0 (NO_ERROR)
> 2024-08-13 15:51:49.836  - info: host.iobroker-pi Restart adapter system.adapter.hm-rpc.0 because enabled
> 2024-08-13 15:51:52.253  - error: hm-rega.0 (2659) CCU 192.168.178.12 unreachable
> 2024-08-13 15:52:03.933  - error: hm-rpc.2 (6575) Init not possible, going to stop: connect EHOSTUNREACH 192.168.178.12:2010
> 2024-08-13 15:52:03.935  - error: hm-rpc.1 (6586) Init not possible, going to stop: connect EHOSTUNREACH 192.168.178.12:2001
> 2024-08-13 15:52:03.960  - info: hm-rpc.1 (6586) xmlrpc -> 192.168.178.12:2001/ init ["http://192.168.178.10:12001",""]
> 2024-08-13 15:52:03.964  - info: hm-rpc.2 (6575) xmlrpc -> 192.168.178.12:2010/ init ["http://192.168.178.10:12010",""]
> 2024-08-13 15:52:04.969  - info: hm-rpc.1 (6586) terminating
> 2024-08-13 15:52:04.971  - info: hm-rpc.1 (6586) Terminated (NO_ERROR): Without reason
> 2024-08-13 15:52:04.978  - info: hm-rpc.2 (6575) terminating
> 2024-08-13 15:52:04.980  - info: hm-rpc.2 (6575) Terminated (NO_ERROR): Without reason
> 2024-08-13 15:52:05.572  - info: host.iobroker-pi instance system.adapter.hm-rpc.1 terminated with code 0 (NO_ERROR)
> 2024-08-13 15:52:05.573  - info: host.iobroker-pi Restart adapter system.adapter.hm-rpc.1 because enabled
> 2024-08-13 15:52:05.618  - info: host.iobroker-pi instance system.adapter.hm-rpc.2 terminated with code 0 (NO_ERROR)
> 2024-08-13 15:52:05.619  - info: host.iobroker-pi Restart adapter system.adapter.hm-rpc.2 because enabled
> 2024-08-13 15:52:19.916  - info: host.iobroker-pi instance system.adapter.hm-rpc.0 started with pid 7348
>

-bash: -/var/lib/lxcfs: No such file or directory
-bash: Files: command not found
-bash: /var:: No such file or directory
-bash: du:: command not found
-bash: 4.6G: command not found
-bash: 3.3G: command not found
-bash: 2.9G: command not found
-bash: 2.9G: command not found
-bash: 729M: command not found
-bash: Archived: command not found
-bash: /opt/iobroker/backups:: No such file or directory
-bash: 82M: command not found
-bash: /opt/iobroker/iobroker-data:: No such file or directory
-bash: 747M: command not found
-bash: 594M: command not found
-bash: 441M: command not found
-bash: 409M: command not found
-bash: 408M: command not found
-bash: The: command not found
-bash: 27M: command not found
-bash: 24M: command not found
-bash: 15M: command not found
-bash: 8.7M: command not found
-bash: 8.7M: command not found
-bash: USB-Devices: command not found
-bash: USB-Sticks: command not found
-bash: No: command not found
-bash: node_modules: command not found
node:internal/modules/cjs/loader:1148
  throw err;
  ^

Error: Cannot find module '/home/wibear/v20.16.0'
    at Module._resolveFilename (node:internal/modules/cjs/loader:1145:15)
    at Module._load (node:internal/modules/cjs/loader:986:27)
    at Function.executeUserEntryPoint [as runMain] (node:internal/modules/run_main:174:12)
    at node:internal/main/run_main_module:28:49 {
  code: 'MODULE_NOT_FOUND',
  requireStack: []
}

Node.js v20.16.0
node:internal/modules/cjs/loader:1080
  throw err;
  ^

Error: Cannot find module '/home/wibear/v18.18.0'
    at Module._resolveFilename (node:internal/modules/cjs/loader:1077:15)
    at Module._load (node:internal/modules/cjs/loader:922:27)
    at Function.executeUserEntryPoint [as runMain] (node:internal/modules/run_main:86:12)
    at node:internal/main/run_main_module:23:47 {
  code: 'MODULE_NOT_FOUND',
  requireStack: []
}

Node.js v18.18.0
npm error code ENOVERSIONS
npm error No versions available for 10.8.2
npm error A complete log of this run can be found in: /home/wibear/.npm/_logs/2024-08-13T13_53_15_245Z-debug-0.log
-bash: node_modules: command not found
-bash: nodejs:: command not found
-bash: Installed:: command not found
-bash: Candidate:: command not found
-bash: Version: command not found
-bash: node_modules: command not found
-bash: 500: command not found
-bash: 100: command not found
-bash: 20.15.1-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.15.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.14.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.13.1-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.13.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.12.2-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.12.1-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.12.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.11.1-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.11.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.10.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.9.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.8.1-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.8.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.7.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.6.1-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.6.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.5.1-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.5.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.4.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.3.1-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.3.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.2.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.1.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 20.0.0-1nodesource1: command not found
-bash: 500: command not found
-bash: 12.22.12~dfsg-1~deb11u4: command not found
-bash: 500: command not found
-bash: Temp: command not found
-bash: No: command not found
-bash: Errors: command not found
-bash: node_modules: command not found
-bash: ioBroker: command not found
iobroker [command]

Commands:
  iobroker setup                                               Setup ioBroker
  iobroker start [all|<adapter>.<instance>|<adapter>]          Starts the js-controller or a specified adapter instance or all instances of an adapter
  iobroker stop [<adapter>.<instance>|<adapter>]               stops the js-controller or a specified adapter instance or all instances of an adapter
  iobroker restart [<adapter>.<instance>|<adapter>]            Restarts js-controller or a specified adapter instance or all instances of an adapter  [aliases: r]
  iobroker debug <adapter>[.<instance>]                        Starts a Node.js debugging session for the adapter instance
  iobroker info                                                Shows the host info
  iobroker logs [<adapter>]                                    Monitor log
  iobroker add <adapter> [desiredNumber]                       Add instance of adapter  [aliases: a]
  iobroker install <adapter>                                   Installs a specified adapter  [aliases: i]
  iobroker rebuild [<module>]                                  Rebuild all native modules or path
  iobroker url <url> [<name>]                                  Install adapter from specified url, e.g. GitHub
  iobroker del <adapter>                                       Remove adapter and all instances from this host  [aliases: delete]
  iobroker del <adapter>.<instance>                            Remove adapter instance  [aliases: delete]
  iobroker update [<repositoryUrl>]                            Update repository and list adapters
  iobroker upgrade                                             Upgrade management
  iobroker upload [all|<adapter>]                              Upload management  [aliases: u]
  iobroker object                                              Object management  [aliases: o]
  iobroker state                                               State management  [aliases: s]
  iobroker message <adapter>[.instance] <command> [<message>]  Send message to adapter instance/s
  iobroker list <type> [<filter>]                              List all entries, like objects
  iobroker chmod <mode> <file>                                 Change file rights
  iobroker chown <user> <group> <file>                         Change file ownership
  iobroker touch <file>                                        Touch file
  iobroker rm <file>                                           Remove file
  iobroker file                                                File management
  iobroker user                                                User commands
  iobroker group                                               group management
  iobroker host <hostname>                                     Set host to given hostname
  iobroker set <adapter>.<instance>                            Change settings of adapter config
  iobroker license <license.file or license.text>              Update license by given file
  iobroker cert                                                Certificate management
  iobroker clean <yes>                                         Clears all objects and states
  iobroker backup                                              Create backup
  iobroker restore <backup name or path>                       Restore a specified backup
  iobroker validate <backup name or path>                      Validate a specified backup
  iobroker status [all|<adapter>.<instance>]                   Status of ioBroker or adapter instance  [aliases: isrun]
  iobroker repo [<name>]                                       Show repo information
  iobroker uuid                                                Show uuid of the installation  [aliases: id]
  iobroker unsetup                                             Reset license, installation secret and language
  iobroker fix                                                 Execute the installation fixer script, this updates your ioBroker installation
  iobroker nodejs-update [<major-version>]                     Upgrade the Node.JS installation to the current LTS
  iobroker multihost                                           Multihost management
  iobroker compact                                             compact group management
  iobroker plugin                                              Plugin management
  iobroker vendor <passphrase> [<vendor.json>]                 Update the vendor information using given passphrase
  iobroker version [<adapter>]                                 Show version of js-controller or specified adapter  [aliases: v]

Options:
  --help  Show help  [boolean]
-bash: Objects: command not found
-bash: States: command not found
-bash: Core: command not found
-bash: js-controller:: command not found
-bash: admin:: command not found
-bash: javascript:: command not found
node:internal/modules/cjs/loader:1148
  throw err;
  ^

Error: Cannot find module '/home/wibear/modules'
    at Module._resolveFilename (node:internal/modules/cjs/loader:1145:15)
    at Module._load (node:internal/modules/cjs/loader:986:27)
    at Function.executeUserEntryPoint [as runMain] (node:internal/modules/run_main:174:12)
    at node:internal/main/run_main_module:28:49 {
  code: 'MODULE_NOT_FOUND',
  requireStack: []
}

Node.js v20.16.0
-bash: command substitution: line 129: syntax error near unexpected token `('
-bash: command substitution: line 129: `+-- iobroker.vw-connect@0.5.3 (git+ssh://git@github.com/TA2k/ioBroker.vw-connect.git#b5fbfb41f65b8a1efb646e9efb68f1cbd1627d27)'
-bash: Unknown: command not found
wibear@iobroker-pi:~ $
wibear@iobroker-pi:~ $ ============ Mark until here for C&P =============
[1] 7854
-bash: ============: command not found
-bash: P: command not found
[1]+  Exit 127                ============ Mark until here for C

[Thomas Braun]

@wibear

Bitte nochmal, das ist irgendwie durcheinander.

[wibear]

@thomas-braun

Passt es so?

======================= SUMMARY =======================
                        v.2024-05-22


   Static hostname: iobroker-pi
         Icon name: computer
  Operating System: Raspbian GNU/Linux 11 (bullseye)
            Kernel: Linux 6.6.44-v7l+
      Architecture: arm

Installation:           native
Kernel:                 armv7l
Userland:               32 bit
Timezone:               Europe/Berlin (CEST, +0200)
User-ID:                1000
Display-Server:         false
Boot Target:            multi-user.target

Pending OS-Updates:     0
Pending iob updates:    1

Nodejs-Installation:
/usr/bin/nodejs         v20.16.0
/usr/bin/node           v20.16.0
/usr/bin/npm            10.8.1
/usr/bin/npx            10.8.1
/usr/bin/corepack       0.28.2

Recommended versions are nodejs  and npm
Your nodejs installation is correct

MEMORY:
               total        used        free      shared  buff/cache   available
Mem:            3.9G        1.0G        2.2G        1.0M        704M        2.8G
Swap:            99M          0B         99M
Total:          4.0G        1.0G        2.3G

Active iob-Instances:   6
Active repo(s): stable

ioBroker Core:          js-controller           5.0.19
                        admin                   7.0.22

ioBroker Status:        iobroker is running on this host.


Objects type: jsonl
States  type: jsonl

Status admin and web instance:
+ system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
  system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin

Objects:                7430
States:                 6249

Size of iob-Database:

17M     /opt/iobroker/iobroker-data/objects.jsonl
11M     /opt/iobroker/iobroker-data/states.jsonl



=================== END OF SUMMARY ====================

=== Mark text until here for copying ===
wibear@iobroker-pi:~ $ b nodejs-update 20
-bash: b: command not found
wibear@iobroker-pi:~ $

[Thomas Braun]

@wibear

Starte die Kiste mal komplett durch und dann gibst du uns die Langfassung.

[wibear]

@thomas-braun

Nach reboot:

Skript v.2024-05-22

*** BASE SYSTEM ***
   Static hostname: iobroker-pi
         Icon name: computer
  Operating System: Raspbian GNU/Linux 11 (bullseye)
            Kernel: Linux 6.6.44-v7l+
      Architecture: arm

Model           : Raspberry Pi 4 Model B Rev 1.5
Docker          : false
Virtualization  : none
Kernel          : armv7l
Userland        : 32 bit

Systemuptime and Load:
 16:10:24 up 1 min,  1 user,  load average: 2.37, 1.01, 0.38
CPU threads: 4


*** RASPBERRY THROTTLING ***
Current issues:
No throttling issues detected.

Previously detected issues:
No throttling issues detected.

*** Time and Time Zones ***
               Local time: Tue 2024-08-13 16:10:25 CEST
           Universal time: Tue 2024-08-13 14:10:25 UTC
                 RTC time: n/a
                Time zone: Europe/Berlin (CEST, +0200)
System clock synchronized: yes
              NTP service: active
          RTC in local TZ: no

*** Users and Groups ***
User that called 'iob diag':
wibear
HOME=/home/wibear
GROUPS=wibear adm dialout cdrom sudo audio video plugdev games users input render netdev gpio i2c spi iobroker

User that is running 'js-controller':
iobroker
HOME=/home/iobroker
GROUPS=iobroker tty dialout audio video plugdev bluetooth gpio i2c

*** Display-Server-Setup ***
Display-Server: false
Desktop:
Terminal:       tty
Boot Target:    multi-user.target

*** MEMORY ***
               total        used        free      shared  buff/cache   available
Mem:            3.9G        1.0G        2.3G        1.0M        519M        2.7G
Swap:            99M          0B         99M
Total:          4.0G        1.0G        2.4G

Active iob-Instances:   10

         3885 M total memory
         1016 M used memory
          156 M active memory
         1281 M inactive memory
         2349 M free memory
           48 M buffer memory
          471 M swap cache
           99 M total swap
            0 M used swap
           99 M free swap

*** top - Table Of Processes  ***
top - 16:10:25 up 1 min,  1 user,  load average: 2.37, 1.01, 0.38
Tasks: 202 total,   1 running, 201 sleeping,   0 stopped,   0 zombie
%Cpu(s): 16.7 us,  3.0 sy,  0.0 ni, 80.3 id,  0.0 wa,  0.0 hi,  0.0 si,  0.0 st
MiB Mem :   3885.9 total,   2349.2 free,   1016.4 used,    520.2 buff/cache
MiB Swap:    100.0 total,    100.0 free,      0.0 used.   2742.4 avail Mem

*** FAILED SERVICES ***

  UNIT                       LOAD   ACTIVE SUB    DESCRIPTION
* pivccu-dkms.service        loaded failed failed piVCCU DKMS Modules
* pivccu-rpi-modules.service loaded failed failed piVCCU RPi Kernel loader

LOAD   = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB    = The low-level unit activation state, values depend on unit type.
2 loaded units listed.

*** FILESYSTEM ***
Filesystem     Type      Size  Used Avail Use% Mounted on
/dev/root      ext4       29G   11G   18G  39% /
devtmpfs       devtmpfs  1.7G     0  1.7G   0% /dev
tmpfs          tmpfs     1.9G     0  1.9G   0% /dev/shm
tmpfs          tmpfs     778M  1.1M  777M   1% /run
tmpfs          tmpfs     5.0M  4.0K  5.0M   1% /run/lock
/dev/mmcblk0p1 vfat      255M   63M  193M  25% /boot
tmpfs          tmpfs     389M     0  389M   0% /run/user/1000

Messages concerning ext4 filesystem in dmesg:
[Tue Aug 13 16:08:37 2024] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 snd_bcm2835.enable_headphones=1 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_hdmi=0  smsc95xx.macaddr=D8:3A:DD:16:18:C4 vc_mem.mem_base=0x3f000000 vc_mem.mem_size=0x3f600000  console=tty1 root=PARTUUID=e605bf32-02 rootfstype=ext4 fsck.repair=yes rootwait
[Tue Aug 13 16:08:38 2024] EXT4-fs (mmcblk0p2): mounted filesystem d3104e7d-5f59-47e0-8621-290882475163 ro with ordered data mode. Quota mode: none.
[Tue Aug 13 16:08:38 2024] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[Tue Aug 13 16:08:39 2024] EXT4-fs (mmcblk0p2): re-mounted d3104e7d-5f59-47e0-8621-290882475163 r/w. Quota mode: none.

Show mounted filesystems:
TARGET                       SOURCE         FSTYPE     OPTIONS
/                            /dev/mmcblk0p2 ext4       rw,noatime
|-/dev                       devtmpfs       devtmpfs   rw,relatime,size=1726396k,nr_inodes=34271,mode=755
| |-/dev/shm                 tmpfs          tmpfs      rw,nosuid,nodev
| |-/dev/pts                 devpts         devpts     rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000
| `-/dev/mqueue              mqueue         mqueue     rw,nosuid,nodev,noexec,relatime
|-/proc                      proc           proc       rw,relatime
| `-/proc/sys/fs/binfmt_misc systemd-1      autofs     rw,relatime,fd=30,pgrp=1,timeout=0,minproto=5,maxproto=5,direct
|-/sys                       sysfs          sysfs      rw,nosuid,nodev,noexec,relatime
| |-/sys/kernel/security     securityfs     securityfs rw,nosuid,nodev,noexec,relatime
| |-/sys/fs/cgroup           cgroup2        cgroup2    rw,nosuid,nodev,noexec,relatime
| |-/sys/fs/pstore           pstore         pstore     rw,nosuid,nodev,noexec,relatime
| |-/sys/fs/bpf              bpf            bpf        rw,nosuid,nodev,noexec,relatime,mode=700
| |-/sys/kernel/tracing      tracefs        tracefs    rw,nosuid,nodev,noexec,relatime
| |-/sys/kernel/debug        debugfs        debugfs    rw,nosuid,nodev,noexec,relatime
| |-/sys/kernel/config       configfs       configfs   rw,nosuid,nodev,noexec,relatime
| `-/sys/fs/fuse/connections fusectl        fusectl    rw,nosuid,nodev,noexec,relatime
|-/run                       tmpfs          tmpfs      rw,nosuid,nodev,size=795828k,nr_inodes=819200,mode=755
| |-/run/lock                tmpfs          tmpfs      rw,nosuid,nodev,noexec,relatime,size=5120k
| |-/run/rpc_pipefs          sunrpc         rpc_pipefs rw,relatime
| `-/run/user/1000           tmpfs          tmpfs      rw,nosuid,nodev,relatime,size=397912k,nr_inodes=99478,mode=700,uid=1000,gid=1000
|-/boot                      /dev/mmcblk0p1 vfat       rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=ascii,shortname=mixed,errors=remount-ro
`-/var/lib/lxcfs             lxcfs          fuse.lxcfs rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other

Files in neuralgic directories:

/var:
du: cannot access '/var/lib/lxcfs/cgroup': Input/output error
4.7G    /var/
3.3G    /var/log
2.9G    /var/log/journal/6462312882a642219bbda7aff5f4f5b9
2.9G    /var/log/journal
734M    /var/lib

Archived and active journals take up 2.8G in the file system.

/opt/iobroker/backups:
82M     /opt/iobroker/backups/

/opt/iobroker/iobroker-data:
752M    /opt/iobroker/iobroker-data/
594M    /opt/iobroker/iobroker-data/files
441M    /opt/iobroker/iobroker-data/files/javascript.admin
409M    /opt/iobroker/iobroker-data/files/javascript.admin/static
408M    /opt/iobroker/iobroker-data/files/javascript.admin/static/js

The five largest files in iobroker-data are:
27M     /opt/iobroker/iobroker-data/files/backitup.admin/static/js/main.ce422ec2.js.map
24M     /opt/iobroker/iobroker-data/files/web.admin/static/js/main.135279a0.js.map
18M     /opt/iobroker/iobroker-data/objects.jsonl
12M     /opt/iobroker/iobroker-data/states.jsonl
8.7M    /opt/iobroker/iobroker-data/files/javascript.admin/static/js/838.0aa41cb0.chunk.js.map

USB-Devices by-id:
USB-Sticks -  Avoid direct links to /dev/tty* in your adapter setups, please always prefer the links 'by-id':

No Devices found 'by-id'




*** NodeJS-Installation ***

/usr/bin/nodejs         v20.16.0
/usr/bin/node           v20.16.0
/usr/bin/npm            10.8.1
/usr/bin/npx            10.8.1
/usr/bin/corepack       0.28.2


nodejs:
  Installed: 20.16.0-1nodesource1
  Candidate: 20.16.0-1nodesource1
  Version table:
 *** 20.16.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
        100 /var/lib/dpkg/status
     20.15.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.15.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.14.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.13.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.13.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.12.2-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.12.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.12.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.11.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.11.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.10.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.9.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.8.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.8.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.7.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.6.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.6.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.5.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.5.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.4.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.3.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.3.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.2.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.1.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.0.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     12.22.12~dfsg-1~deb11u4 500
        500 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf Packages

Temp directories causing npm8 problem: 0
No problems detected

Errors in npm tree:

*** ioBroker-Installation ***

ioBroker Status
iobroker is running on this host.


Objects type: jsonl
States  type: jsonl

Core adapters versions
js-controller:  5.0.19
admin:          7.0.22
javascript:     8.7.6

nodejs modules from github:     1
+-- iobroker.vw-connect@0.5.3 (git+ssh://git@github.com/TA2k/ioBroker.vw-connect.git#b5fbfb41f65b8a1efb646e9efb68f1cbd1627d27)

Adapter State
+ system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
+ system.adapter.alexa2.0                 : alexa2                : iobroker-pi                              -  enabled
+ system.adapter.backitup.0               : backitup              : iobroker-pi                              -  enabled
  system.adapter.device-reminder.0        : device-reminder       : iobroker-pi                              -  enabled
  system.adapter.discovery.0              : discovery             : iobroker-pi                              -  enabled
  system.adapter.ems-esp.0                : ems-esp               : iobroker-pi                              -  enabled
  system.adapter.fb-checkpresence.0       : fb-checkpresence      : iobroker-pi                              -  enabled
  system.adapter.habpanel.0               : habpanel              : iobroker-pi                              -  enabled
+ system.adapter.history.0                : history               : iobroker-pi                              -  enabled
+ system.adapter.hm-rega.0                : hm-rega               : iobroker-pi                              -  enabled
+ system.adapter.hm-rpc.0                 : hm-rpc                : iobroker-pi                              -  enabled, port: 18701
  system.adapter.hm-rpc.1                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12001
  system.adapter.hm-rpc.2                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12010
+ system.adapter.influxdb.0               : influxdb              : iobroker-pi                              -  enabled, port: 8086
  system.adapter.info.0                   : info                  : iobroker-pi                              -  enabled
+ system.adapter.javascript.0             : javascript            : iobroker-pi                              -  enabled
  system.adapter.mqtt.0                   : mqtt                  : iobroker-pi                              -  enabled, port: 1883, bind: 192.168.178.10
  system.adapter.netatmo-crawler.0        : netatmo-crawler       : iobroker-pi                              -  enabled
  system.adapter.rpi2.0                   : rpi2                  : iobroker-pi                              -  enabled
  system.adapter.shelly.0                 : shelly                : iobroker-pi                              -  enabled, port: 1882, bind: 0.0.0.0
  system.adapter.simple-api.0             : simple-api            : iobroker-pi                              -  enabled, port: 8087, bind: 0.0.0.0, run as: admin
  system.adapter.tr-064.0                 : tr-064                : iobroker-pi                              -  enabled
  system.adapter.tuya.0                   : tuya                  : iobroker-pi                              - disabled
  system.adapter.vw-connect.0             : vw-connect            : iobroker-pi                              -  enabled
  system.adapter.weatherunderground.0     : weatherunderground    : iobroker-pi                              - disabled
  system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin
+ system.adapter.whatsapp-cmb.0           : whatsapp-cmb          : iobroker-pi                              -  enabled

+ instance is alive

Enabled adapters with bindings
+ system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
+ system.adapter.hm-rpc.0                 : hm-rpc                : iobroker-pi                              -  enabled, port: 18701
  system.adapter.hm-rpc.1                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12001
  system.adapter.hm-rpc.2                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12010
+ system.adapter.influxdb.0               : influxdb              : iobroker-pi                              -  enabled, port: 8086
  system.adapter.mqtt.0                   : mqtt                  : iobroker-pi                              -  enabled, port: 1883, bind: 192.168.178.10
  system.adapter.shelly.0                 : shelly                : iobroker-pi                              -  enabled, port: 1882, bind: 0.0.0.0
  system.adapter.simple-api.0             : simple-api            : iobroker-pi                              -  enabled, port: 8087, bind: 0.0.0.0, run as: admin
  system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin

ioBroker-Repositories
stable        : http://download.iobroker.net/sources-dist.json
beta          : http://download.iobroker.net/sources-dist-latest.json

Active repo(s): stable

Installed ioBroker-Instances
Used repository: stable
Adapter    "admin"        : 7.0.22   , installed 7.0.22
Adapter    "alexa2"       : 3.26.5   , installed 3.26.5
Adapter    "backitup"     : 3.0.16   , installed 3.0.16
Adapter    "device-reminder": 3.1.2  , installed 3.1.2
Adapter    "discovery"    : 4.5.0    , installed 4.5.0
Adapter    "ems-esp"      : 3.5.0    , installed 3.5.0
Adapter    "fb-checkpresence": 1.2.4 , installed 1.2.4
Adapter    "habpanel"     : 0.5.0    , installed 0.5.0
Adapter    "history"      : 3.0.1    , installed 3.0.1
Adapter    "hm-rega"      : 4.0.0    , installed 4.0.0
Adapter    "hm-rpc"       : 1.17.0   , installed 1.17.0
Adapter    "influxdb"     : 4.0.2    , installed 4.0.2
Adapter    "javascript"   : 8.7.6    , installed 8.7.6
Controller "js-controller": 6.0.9    , installed 5.0.19 [Updatable]
Adapter    "mqtt"         : 5.2.0    , installed 5.2.0
Adapter    "netatmo-crawler": 0.8.1  , installed 0.8.1
Adapter    "rpi2"         : 1.3.2    , installed 1.3.2
Adapter    "shelly"       : 7.0.0    , installed 7.0.0
Adapter    "simple-api"   : 2.8.0    , installed 2.8.0
Adapter    "socketio"     : 6.7.1    , installed 6.7.1
Adapter    "tr-064"       : 4.3.0    , installed 4.3.0
Adapter    "tuya"         : 3.15.0   , installed 3.15.0
Adapter    "weatherunderground": 3.7.0, installed 3.7.0
Adapter    "web"          : 6.2.5    , installed 6.2.5
Adapter    "whatsapp-cmb" : 0.3.0    , installed 0.3.0
Adapter    "ws"           : 2.6.2    , installed 2.6.2

Objects and States
Please stand by - This may take a while
Objects:        7430
States:         6295

*** OS-Repositories and Updates ***
Hit:1 http://archive.raspberrypi.org/debian bullseye InRelease
Hit:2 https://repos.influxdata.com/debian bullseye InRelease
Hit:3 http://raspbian.raspberrypi.org/raspbian bullseye InRelease
Hit:4 https://packages.grafana.com/oss/deb stable InRelease
Hit:5 https://apt.pivccu.de/piVCCU stable InRelease
Hit:6 https://deb.nodesource.com/node_20.x nodistro InRelease
Reading package lists...
Pending Updates: 0

*** Listening Ports ***
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State       User       Inode      PID/Program name
tcp        0      0 10.0.3.1:53             0.0.0.0:*               LISTEN      0          6228       814/dnsmasq
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN      0          6194       785/sshd: /usr/sbin
tcp        0      0 192.168.178.10:12001    0.0.0.0:*               LISTEN      1001       12319      1854/io.hm-rpc.1
tcp        0      0 192.168.178.10:12010    0.0.0.0:*               LISTEN      1001       12330      1869/io.hm-rpc.2
tcp        0      0 0.0.0.0:1882            0.0.0.0:*               LISTEN      1001       9377       1407/io.shelly.0
tcp        0      0 192.168.178.10:1883     0.0.0.0:*               LISTEN      1001       8528       1324/io.mqtt.0
tcp        0      0 127.0.0.1:9001          0.0.0.0:*               LISTEN      1001       7195       905/iobroker.js-con
tcp        0      0 127.0.0.1:9000          0.0.0.0:*               LISTEN      1001       5644       905/iobroker.js-con
tcp        0      0 127.0.0.1:8088          0.0.0.0:*               LISTEN      999        6272       730/influxd
tcp6       0      0 :::22                   :::*                    LISTEN      0          6196       785/sshd: /usr/sbin
tcp6       0      0 :::3000                 :::*                    LISTEN      111        5642       904/grafana
tcp6       0      0 :::8086                 :::*                    LISTEN      999        6362       730/influxd
tcp6       0      0 :::8087                 :::*                    LISTEN      1001       6952       1464/io.simple-api.
tcp6       0      0 :::8082                 :::*                    LISTEN      1001       7769       1483/io.web.0
tcp6       0      0 :::8081                 :::*                    LISTEN      1001       7239       990/io.admin.0
udp        0      0 0.0.0.0:5353            0.0.0.0:*                           108        787        337/avahi-daemon: r
udp        0      0 0.0.0.0:47656           0.0.0.0:*                           108        789        337/avahi-daemon: r
udp        0      0 10.0.3.1:53             0.0.0.0:*                           0          6227       814/dnsmasq
udp        0      0 0.0.0.0:67              0.0.0.0:*                           0          6224       814/dnsmasq
udp        0      0 0.0.0.0:68              0.0.0.0:*                           0          897        598/dhclient
udp6       0      0 :::5353                 :::*                                108        788        337/avahi-daemon: r
udp6       0      0 :::34059                :::*                                108        790        337/avahi-daemon: r

*** Log File - Last 25 Lines ***

2024-08-13 16:10:57.691  - info: hm-rpc.1 (1854) starting. Version 1.17.0 in /opt/iobroker/node_modules/iobroker.hm-rpc, node: v20.16.0, js-controller: 5.0.19
2024-08-13 16:10:58.329  - info: hm-rpc.1 (1854) xmlrpc server is trying to listen on 192.168.178.10:12001
2024-08-13 16:10:58.342  - info: hm-rpc.1 (1854) xmlrpc client is trying to connect to 192.168.178.12:2001/ with ["http://192.168.178.10:12001","iobroker-pi:hm-rpc.1:d56a41b7e622f59142e1fdc67550700c"]
2024-08-13 16:10:59.322  - info: shelly.0 (1407) [MQTT] Client Close:  (shelly1pmminig3 / shelly1pmminig3-5432044f4ff4 / shelly1pmminig3#5432044f4ff4#1) (false)
2024-08-13 16:10:59.922  - error: shelly.0 (1407) [MQTT] Unable to get mqttprefix of client with id "shelly1pmminig3-5432044f4ff4"
2024-08-13 16:11:00.713  - info: hm-rpc.2 (1869) starting. Version 1.17.0 in /opt/iobroker/node_modules/iobroker.hm-rpc, node: v20.16.0, js-controller: 5.0.19
2024-08-13 16:11:00.868  - info: shelly.0 (1407) [MQTT] Client Close: 192.168.178.78 (shellyplusplugs / shellyplusplugs-d4d4dae85f70 / shellyplusplugs#d4d4dae85f70#1) (false)
2024-08-13 16:11:00.928  - error: shelly.0 (1407) [MQTT] Error in function setMqttPrefixHttp (Gen 1) for  (undefined / undefined / undefined): TypeError: Cannot read properties of undefined (reading 'replace')
2024-08-13 16:11:00.929  - error: shelly.0 (1407) [MQTT] Unable to get mqttprefix of client with id "shellyplusplugs-d4d4dae85f70"
2024-08-13 16:11:01.071  - info: hm-rpc.2 (1869) xmlrpc server is trying to listen on 192.168.178.10:12010
2024-08-13 16:11:01.077  - info: hm-rpc.2 (1869) xmlrpc client is trying to connect to 192.168.178.12:2010/ with ["http://192.168.178.10:12010","iobroker-pi:hm-rpc.2:03c58894ec83886e7c67f29e17b46f89"]
2024-08-13 16:11:01.519  - error: hm-rpc.2 (1869) Init not possible, going to stop: connect EHOSTUNREACH 192.168.178.12:2010
2024-08-13 16:11:01.525  - error: hm-rpc.1 (1854) Init not possible, going to stop: connect EHOSTUNREACH 192.168.178.12:2001
2024-08-13 16:11:02.712  - info: ems-esp.0 (1426) ems  : energy polling every 10 minutes
2024-08-13 16:11:02.713  - info: ems-esp.0 (1426) ems  : polling every 15 secs
2024-08-13 16:11:10.056  - info: fb-checkpresence.0 (1726) createFbDeviceObjects finished successfully
2024-08-13 16:11:10.058  - info: fb-checkpresence.0 (1726) states successfully subscribed
2024-08-13 16:11:10.059  - info: fb-checkpresence.0 (1726) loop successfully started
2024-08-13 16:11:20.232  - info: hm-rpc.0 (1791) binrpc -> 192.168.178.12:8701/ init ["xmlrpc_bin://192.168.178.10:18701",""]
2024-08-13 16:11:20.238  - error: hm-rpc.0 (1791) Cannot call init: [xmlrpc_bin://192.168.178.10:18701, ""] Socket closed before the connection was established
2024-08-13 16:11:20.246  - info: hm-rpc.0 (1791) terminating
2024-08-13 16:11:20.248  - info: hm-rpc.0 (1791) Terminated (NO_ERROR): Without reason
2024-08-13 16:11:20.853  - info: host.iobroker-pi instance system.adapter.hm-rpc.0 terminated with code 0 (NO_ERROR)
2024-08-13 16:11:20.854  - info: host.iobroker-pi Restart adapter system.adapter.hm-rpc.0 because enabled
2024-08-13 16:11:23.334  - error: hm-rega.0 (1231) CCU 192.168.178.12 unreachable

[Meister Mopper]

@wibear

Es ist dir doch oben schon einmal gelungen, klopp bitte die lange Fassung in </> (codetags) hier rein.

Das ist sonst grottenschlecht zu lesen.

[Thomas Braun]

@wibear sagte in pivCCU nach Update node.js nicht erreichbar:

UNIT LOAD ACTIVE SUB DESCRIPTION

pivccu-dkms.service loaded failed failed piVCCU DKMS Modules
pivccu-rpi-modules.service loaded failed failed piVCCU RPi Kernel loader

Da klemmt es. Hat aber nix mit nodejs oder dem ioBroker zu tun, da werden die pivCCU Module nicht geladen.

Und wo du einmal dran bist:

Controller "js-controller": 6.0.9 , installed 5.0.19 [Updatable]

iob stop 
iob update
iob upgrade self
iob start

[wibear]

@meister-mopper sagte in pivCCU nach Update node.js nicht erreichbar:

Das ist sonst grottenschlecht zu lesen.

======================= SUMMARY =======================
                        v.2024-05-22


   Static hostname: iobroker-pi
         Icon name: computer
  Operating System: Raspbian GNU/Linux 11 (bullseye)
            Kernel: Linux 6.6.44-v7l+
      Architecture: arm

Installation:           native
Kernel:                 armv7l
Userland:               32 bit
Timezone:               Europe/Berlin (CEST, +0200)
User-ID:                1000
Display-Server:         false
Boot Target:            multi-user.target

Pending OS-Updates:     0
Pending iob updates:    1

Nodejs-Installation:
/usr/bin/nodejs         v20.16.0
/usr/bin/node           v20.16.0
/usr/bin/npm            10.8.1
/usr/bin/npx            10.8.1
/usr/bin/corepack       0.28.2

Recommended versions are nodejs 20.16.0 and npm 10.8.1
Your nodejs installation is correct

MEMORY:
               total        used        free      shared  buff/cache   available
Mem:            3.9G        945M        2.3G        1.0M        604M        2.8G
Swap:            99M          0B         99M
Total:          4.0G        945M        2.4G

Active iob-Instances:   21
Active repo(s): stable

ioBroker Core:          js-controller           5.0.19
                        admin                   7.0.22

ioBroker Status:        iobroker is running on this host.


Objects type: jsonl
States  type: jsonl

Status admin and web instance:
+ system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
+ system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin

Objects:                7430
States:                 6297

Size of iob-Database:

9.6M    /opt/iobroker/iobroker-data/objects.jsonl
13M     /opt/iobroker/iobroker-data/states.jsonl



=================== END OF SUMMARY ====================

[Thomas Braun]

@meister-mopper sagte in pivCCU nach Update node.js nicht erreichbar:

klopp bitte die lange Fassung in </> (codetags) hier rein.

Die Ausgabe von iob diag hat die schon dabei. Muss nur kopiert und eingefügt werden.
Jetzt sind zwei CodeTags drumherum, das ist auch falsch.

[wibear]

@meister-mopper sagte in pivCCU nach Update node.js nicht erreichbar:

klopp bitte die lange Fassung in </> (codetags) hier rein

Ist es besser?

Skript v.2024-05-22

*** BASE SYSTEM ***
   Static hostname: iobroker-pi
         Icon name: computer
  Operating System: Raspbian GNU/Linux 11 (bullseye)
            Kernel: Linux 6.6.44-v7l+
      Architecture: arm

Model           : Raspberry Pi 4 Model B Rev 1.5
Docker          : false
Virtualization  : none
Kernel          : armv7l
Userland        : 32 bit

Systemuptime and Load:
 16:21:41 up 13 min,  1 user,  load average: 1.00, 1.08, 0.80
CPU threads: 4


*** RASPBERRY THROTTLING ***
Current issues:
No throttling issues detected.

Previously detected issues:
No throttling issues detected.

*** Time and Time Zones ***
               Local time: Tue 2024-08-13 16:21:42 CEST
           Universal time: Tue 2024-08-13 14:21:42 UTC
                 RTC time: n/a
                Time zone: Europe/Berlin (CEST, +0200)
System clock synchronized: yes
              NTP service: active
          RTC in local TZ: no

*** Users and Groups ***
User that called 'iob diag':
wibear
HOME=/home/wibear
GROUPS=wibear adm dialout cdrom sudo audio video plugdev games users input render netdev gpio i2c spi iobroker

User that is running 'js-controller':
iobroker
HOME=/home/iobroker
GROUPS=iobroker tty dialout audio video plugdev bluetooth gpio i2c

*** Display-Server-Setup ***
Display-Server: false
Desktop:
Terminal:       tty
Boot Target:    multi-user.target

*** MEMORY ***
               total        used        free      shared  buff/cache   available
Mem:            3.9G        941M        2.3G        1.0M        626M        2.8G
Swap:            99M          0B         99M
Total:          4.0G        941M        2.4G

Active iob-Instances:   21

         3885 M total memory
          942 M used memory
          230 M active memory
         1233 M inactive memory
         2317 M free memory
           76 M buffer memory
          550 M swap cache
           99 M total swap
            0 M used swap
           99 M free swap

*** top - Table Of Processes  ***
top - 16:21:42 up 13 min,  1 user,  load average: 1.00, 1.08, 0.80
Tasks: 194 total,   1 running, 193 sleeping,   0 stopped,   0 zombie
%Cpu(s): 30.0 us, 11.4 sy,  0.0 ni, 52.9 id,  4.3 wa,  0.0 hi,  1.4 si,  0.0 st
MiB Mem :   3885.9 total,   2316.9 free,    942.0 used,    627.0 buff/cache
MiB Swap:    100.0 total,    100.0 free,      0.0 used.   2817.4 avail Mem

*** FAILED SERVICES ***

  UNIT                       LOAD   ACTIVE SUB    DESCRIPTION
* pivccu-dkms.service        loaded failed failed piVCCU DKMS Modules
* pivccu-rpi-modules.service loaded failed failed piVCCU RPi Kernel loader

LOAD   = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB    = The low-level unit activation state, values depend on unit type.
2 loaded units listed.

*** FILESYSTEM ***
Filesystem     Type      Size  Used Avail Use% Mounted on
/dev/root      ext4       29G   11G   18G  39% /
devtmpfs       devtmpfs  1.7G     0  1.7G   0% /dev
tmpfs          tmpfs     1.9G     0  1.9G   0% /dev/shm
tmpfs          tmpfs     778M  1.1M  777M   1% /run
tmpfs          tmpfs     5.0M  4.0K  5.0M   1% /run/lock
/dev/mmcblk0p1 vfat      255M   63M  193M  25% /boot
tmpfs          tmpfs     389M     0  389M   0% /run/user/1000

Messages concerning ext4 filesystem in dmesg:
[Tue Aug 13 16:08:37 2024] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 snd_bcm2835.enable_headphones=1 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_hdmi=0  smsc95xx.macaddr=D8:3A:DD:16:18:C4 vc_mem.mem_base=0x3f000000 vc_mem.mem_size=0x3f600000  console=tty1 root=PARTUUID=e605bf32-02 rootfstype=ext4 fsck.repair=yes rootwait
[Tue Aug 13 16:08:38 2024] EXT4-fs (mmcblk0p2): mounted filesystem d3104e7d-5f59-47e0-8621-290882475163 ro with ordered data mode. Quota mode: none.
[Tue Aug 13 16:08:38 2024] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[Tue Aug 13 16:08:39 2024] EXT4-fs (mmcblk0p2): re-mounted d3104e7d-5f59-47e0-8621-290882475163 r/w. Quota mode: none.

Show mounted filesystems:
TARGET                       SOURCE         FSTYPE     OPTIONS
/                            /dev/mmcblk0p2 ext4       rw,noatime
|-/dev                       devtmpfs       devtmpfs   rw,relatime,size=1726396k,nr_inodes=34271,mode=755
| |-/dev/shm                 tmpfs          tmpfs      rw,nosuid,nodev
| |-/dev/pts                 devpts         devpts     rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000
| `-/dev/mqueue              mqueue         mqueue     rw,nosuid,nodev,noexec,relatime
|-/proc                      proc           proc       rw,relatime
| `-/proc/sys/fs/binfmt_misc systemd-1      autofs     rw,relatime,fd=30,pgrp=1,timeout=0,minproto=5,maxproto=5,direct
|-/sys                       sysfs          sysfs      rw,nosuid,nodev,noexec,relatime
| |-/sys/kernel/security     securityfs     securityfs rw,nosuid,nodev,noexec,relatime
| |-/sys/fs/cgroup           cgroup2        cgroup2    rw,nosuid,nodev,noexec,relatime
| |-/sys/fs/pstore           pstore         pstore     rw,nosuid,nodev,noexec,relatime
| |-/sys/fs/bpf              bpf            bpf        rw,nosuid,nodev,noexec,relatime,mode=700
| |-/sys/kernel/tracing      tracefs        tracefs    rw,nosuid,nodev,noexec,relatime
| |-/sys/kernel/debug        debugfs        debugfs    rw,nosuid,nodev,noexec,relatime
| |-/sys/kernel/config       configfs       configfs   rw,nosuid,nodev,noexec,relatime
| `-/sys/fs/fuse/connections fusectl        fusectl    rw,nosuid,nodev,noexec,relatime
|-/run                       tmpfs          tmpfs      rw,nosuid,nodev,size=795828k,nr_inodes=819200,mode=755
| |-/run/lock                tmpfs          tmpfs      rw,nosuid,nodev,noexec,relatime,size=5120k
| |-/run/rpc_pipefs          sunrpc         rpc_pipefs rw,relatime
| `-/run/user/1000           tmpfs          tmpfs      rw,nosuid,nodev,relatime,size=397912k,nr_inodes=99478,mode=700,uid=1000,gid=1000
|-/boot                      /dev/mmcblk0p1 vfat       rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=ascii,shortname=mixed,errors=remount-ro
`-/var/lib/lxcfs             lxcfs          fuse.lxcfs rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other

Files in neuralgic directories:

/var:
du: cannot access '/var/lib/lxcfs/cgroup': Input/output error
4.7G    /var/
3.3G    /var/log
2.9G    /var/log/journal/6462312882a642219bbda7aff5f4f5b9
2.9G    /var/log/journal
738M    /var/lib

Archived and active journals take up 2.8G in the file system.

/opt/iobroker/backups:
82M     /opt/iobroker/backups/

/opt/iobroker/iobroker-data:
746M    /opt/iobroker/iobroker-data/
594M    /opt/iobroker/iobroker-data/files
441M    /opt/iobroker/iobroker-data/files/javascript.admin
409M    /opt/iobroker/iobroker-data/files/javascript.admin/static
408M    /opt/iobroker/iobroker-data/files/javascript.admin/static/js

The five largest files in iobroker-data are:
27M     /opt/iobroker/iobroker-data/files/backitup.admin/static/js/main.ce422ec2.js.map
24M     /opt/iobroker/iobroker-data/files/web.admin/static/js/main.135279a0.js.map
13M     /opt/iobroker/iobroker-data/states.jsonl
9.6M    /opt/iobroker/iobroker-data/objects.jsonl
8.7M    /opt/iobroker/iobroker-data/files/javascript.admin/static/js/838.0aa41cb0.chunk.js.map

USB-Devices by-id:
USB-Sticks -  Avoid direct links to /dev/tty* in your adapter setups, please always prefer the links 'by-id':

No Devices found 'by-id'




*** NodeJS-Installation ***

/usr/bin/nodejs         v20.16.0
/usr/bin/node           v20.16.0
/usr/bin/npm            10.8.1
/usr/bin/npx            10.8.1
/usr/bin/corepack       0.28.2


nodejs:
  Installed: 20.16.0-1nodesource1
  Candidate: 20.16.0-1nodesource1
  Version table:
 *** 20.16.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
        100 /var/lib/dpkg/status
     20.15.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.15.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.14.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.13.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.13.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.12.2-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.12.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.12.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.11.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.11.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.10.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.9.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.8.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.8.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.7.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.6.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.6.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.5.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.5.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.4.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.3.1-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.3.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.2.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.1.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     20.0.0-1nodesource1 600
        500 https://deb.nodesource.com/node_20.x nodistro/main armhf Packages
     12.22.12~dfsg-1~deb11u4 500
        500 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf Packages

Temp directories causing npm8 problem: 0
No problems detected

Errors in npm tree:

*** ioBroker-Installation ***

ioBroker Status
iobroker is running on this host.


Objects type: jsonl
States  type: jsonl

Core adapters versions
js-controller:  5.0.19
admin:          7.0.22
javascript:     8.7.6

nodejs modules from github:     1
+-- iobroker.vw-connect@0.5.3 (git+ssh://git@github.com/TA2k/ioBroker.vw-connect.git#b5fbfb41f65b8a1efb646e9efb68f1cbd1627d27)

Adapter State
+ system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
+ system.adapter.alexa2.0                 : alexa2                : iobroker-pi                              -  enabled
+ system.adapter.backitup.0               : backitup              : iobroker-pi                              -  enabled
+ system.adapter.device-reminder.0        : device-reminder       : iobroker-pi                              -  enabled
+ system.adapter.discovery.0              : discovery             : iobroker-pi                              -  enabled
+ system.adapter.ems-esp.0                : ems-esp               : iobroker-pi                              -  enabled
+ system.adapter.fb-checkpresence.0       : fb-checkpresence      : iobroker-pi                              -  enabled
  system.adapter.habpanel.0               : habpanel              : iobroker-pi                              -  enabled
+ system.adapter.history.0                : history               : iobroker-pi                              -  enabled
+ system.adapter.hm-rega.0                : hm-rega               : iobroker-pi                              -  enabled
+ system.adapter.hm-rpc.0                 : hm-rpc                : iobroker-pi                              -  enabled, port: 18701
  system.adapter.hm-rpc.1                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12001
  system.adapter.hm-rpc.2                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12010
+ system.adapter.influxdb.0               : influxdb              : iobroker-pi                              -  enabled, port: 8086
  system.adapter.info.0                   : info                  : iobroker-pi                              -  enabled
+ system.adapter.javascript.0             : javascript            : iobroker-pi                              -  enabled
+ system.adapter.mqtt.0                   : mqtt                  : iobroker-pi                              -  enabled, port: 1883, bind: 192.168.178.10
  system.adapter.netatmo-crawler.0        : netatmo-crawler       : iobroker-pi                              -  enabled
+ system.adapter.rpi2.0                   : rpi2                  : iobroker-pi                              -  enabled
+ system.adapter.shelly.0                 : shelly                : iobroker-pi                              -  enabled, port: 1882, bind: 0.0.0.0
+ system.adapter.simple-api.0             : simple-api            : iobroker-pi                              -  enabled, port: 8087, bind: 0.0.0.0, run as: admin
+ system.adapter.tr-064.0                 : tr-064                : iobroker-pi                              -  enabled
  system.adapter.tuya.0                   : tuya                  : iobroker-pi                              - disabled
+ system.adapter.vw-connect.0             : vw-connect            : iobroker-pi                              -  enabled
  system.adapter.weatherunderground.0     : weatherunderground    : iobroker-pi                              - disabled
+ system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin
+ system.adapter.whatsapp-cmb.0           : whatsapp-cmb          : iobroker-pi                              -  enabled

+ instance is alive

Enabled adapters with bindings
+ system.adapter.admin.0                  : admin                 : iobroker-pi                              -  enabled, port: 8081, bind: 0.0.0.0, run as: admin
+ system.adapter.hm-rpc.0                 : hm-rpc                : iobroker-pi                              -  enabled, port: 18701
  system.adapter.hm-rpc.1                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12001
  system.adapter.hm-rpc.2                 : hm-rpc                : iobroker-pi                              -  enabled, port: 12010
+ system.adapter.influxdb.0               : influxdb              : iobroker-pi                              -  enabled, port: 8086
+ system.adapter.mqtt.0                   : mqtt                  : iobroker-pi                              -  enabled, port: 1883, bind: 192.168.178.10
+ system.adapter.shelly.0                 : shelly                : iobroker-pi                              -  enabled, port: 1882, bind: 0.0.0.0
+ system.adapter.simple-api.0             : simple-api            : iobroker-pi                              -  enabled, port: 8087, bind: 0.0.0.0, run as: admin
+ system.adapter.web.0                    : web                   : iobroker-pi                              -  enabled, port: 8082, bind: 0.0.0.0, run as: admin

ioBroker-Repositories
stable        : http://download.iobroker.net/sources-dist.json
beta          : http://download.iobroker.net/sources-dist-latest.json

Active repo(s): stable

Installed ioBroker-Instances
Used repository: stable
Adapter    "admin"        : 7.0.22   , installed 7.0.22
Adapter    "alexa2"       : 3.26.5   , installed 3.26.5
Adapter    "backitup"     : 3.0.16   , installed 3.0.16
Adapter    "device-reminder": 3.1.2  , installed 3.1.2
Adapter    "discovery"    : 4.5.0    , installed 4.5.0
Adapter    "ems-esp"      : 3.5.0    , installed 3.5.0
Adapter    "fb-checkpresence": 1.2.4 , installed 1.2.4
Adapter    "habpanel"     : 0.5.0    , installed 0.5.0
Adapter    "history"      : 3.0.1    , installed 3.0.1
Adapter    "hm-rega"      : 4.0.0    , installed 4.0.0
Adapter    "hm-rpc"       : 1.17.0   , installed 1.17.0
Adapter    "influxdb"     : 4.0.2    , installed 4.0.2
Adapter    "javascript"   : 8.7.6    , installed 8.7.6
Controller "js-controller": 6.0.9    , installed 5.0.19 [Updatable]
Adapter    "mqtt"         : 5.2.0    , installed 5.2.0
Adapter    "netatmo-crawler": 0.8.1  , installed 0.8.1
Adapter    "rpi2"         : 1.3.2    , installed 1.3.2
Adapter    "shelly"       : 7.0.0    , installed 7.0.0
Adapter    "simple-api"   : 2.8.0    , installed 2.8.0
Adapter    "socketio"     : 6.7.1    , installed 6.7.1
Adapter    "tr-064"       : 4.3.0    , installed 4.3.0
Adapter    "tuya"         : 3.15.0   , installed 3.15.0
Adapter    "weatherunderground": 3.7.0, installed 3.7.0
Adapter    "web"          : 6.2.5    , installed 6.2.5
Adapter    "whatsapp-cmb" : 0.3.0    , installed 0.3.0
Adapter    "ws"           : 2.6.2    , installed 2.6.2

Objects and States
Please stand by - This may take a while
Objects:        7430
States:         6279

*** OS-Repositories and Updates ***
Hit:1 https://repos.influxdata.com/debian bullseye InRelease
Hit:2 http://archive.raspberrypi.org/debian bullseye InRelease
Hit:3 http://raspbian.raspberrypi.org/raspbian bullseye InRelease
Hit:4 https://deb.nodesource.com/node_20.x nodistro InRelease
Hit:5 https://apt.pivccu.de/piVCCU stable InRelease
Hit:6 https://packages.grafana.com/oss/deb stable InRelease
Reading package lists...
Pending Updates: 0

*** Listening Ports ***
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State       User       Inode      PID/Program name
tcp        0      0 10.0.3.1:53             0.0.0.0:*               LISTEN      0          6228       814/dnsmasq
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN      0          6194       785/sshd: /usr/sbin
tcp        0      0 192.168.178.10:12001    0.0.0.0:*               LISTEN      1001       39110      5590/io.hm-rpc.1
tcp        0      0 192.168.178.10:12010    0.0.0.0:*               LISTEN      1001       36706      5591/io.hm-rpc.2
tcp        0      0 0.0.0.0:1882            0.0.0.0:*               LISTEN      1001       9377       1407/io.shelly.0
tcp        0      0 192.168.178.10:1883     0.0.0.0:*               LISTEN      1001       8528       1324/io.mqtt.0
tcp        0      0 127.0.0.1:9001          0.0.0.0:*               LISTEN      1001       7195       905/iobroker.js-con
tcp        0      0 127.0.0.1:9000          0.0.0.0:*               LISTEN      1001       5644       905/iobroker.js-con
tcp        0      0 127.0.0.1:8088          0.0.0.0:*               LISTEN      999        6272       730/influxd
tcp6       0      0 :::22                   :::*                    LISTEN      0          6196       785/sshd: /usr/sbin
tcp6       0      0 :::3000                 :::*                    LISTEN      111        5642       904/grafana
tcp6       0      0 :::8086                 :::*                    LISTEN      999        6362       730/influxd
tcp6       0      0 :::8087                 :::*                    LISTEN      1001       6952       1464/io.simple-api.
tcp6       0      0 :::8082                 :::*                    LISTEN      1001       7769       1483/io.web.0
tcp6       0      0 :::8081                 :::*                    LISTEN      1001       7239       990/io.admin.0
udp        0      0 0.0.0.0:5353            0.0.0.0:*                           108        787        337/avahi-daemon: r
udp        0      0 0.0.0.0:47656           0.0.0.0:*                           108        789        337/avahi-daemon: r
udp        0      0 10.0.3.1:53             0.0.0.0:*                           0          6227       814/dnsmasq
udp        0      0 0.0.0.0:67              0.0.0.0:*                           0          6224       814/dnsmasq
udp        0      0 0.0.0.0:68              0.0.0.0:*                           0          897        598/dhclient
udp6       0      0 :::5353                 :::*                                108        788        337/avahi-daemon: r
udp6       0      0 :::34059                :::*                                108        790        337/avahi-daemon: r

*** Log File - Last 25 Lines ***

2024-08-13 16:21:48.384  - info: hm-rpc.2 (4770) Terminated (NO_ERROR): Without reason
2024-08-13 16:21:49.099  - info: host.iobroker-pi instance system.adapter.hm-rpc.1 terminated with code 0 (NO_ERROR)
2024-08-13 16:21:49.099  - info: host.iobroker-pi Restart adapter system.adapter.hm-rpc.1 because enabled
2024-08-13 16:21:49.099  - info: host.iobroker-pi instance system.adapter.hm-rpc.2 terminated with code 0 (NO_ERROR)
2024-08-13 16:21:49.100  - info: host.iobroker-pi Restart adapter system.adapter.hm-rpc.2 because enabled
2024-08-13 16:21:49.884  - info: hm-rpc.0 (5004) starting. Version 1.17.0 in /opt/iobroker/node_modules/iobroker.hm-rpc, node: v20.16.0, js-controller: 5.0.19
2024-08-13 16:21:50.185  - info: hm-rpc.0 (5004) binrpc server is trying to listen on 192.168.178.10:18701
2024-08-13 16:21:50.187  - info: hm-rpc.0 (5004) binrpc client is trying to connect to 192.168.178.12:8701/ with ["xmlrpc_bin://192.168.178.10:18701","iobroker-pi:hm-rpc.0:586ced57dee52ef270bfb61be9f07a73"]
2024-08-13 16:21:50.457  - error: hm-rpc.0 (5004) Init not possible, going to stop: connect EHOSTUNREACH 192.168.178.12:8701
2024-08-13 16:21:50.461  - error: hm-rega.0 (1231) CCU 192.168.178.12 unreachable
2024-08-13 16:22:19.230  - info: host.iobroker-pi instance system.adapter.hm-rpc.1 started with pid 5590
2024-08-13 16:22:19.243  - info: host.iobroker-pi instance system.adapter.hm-rpc.2 started with pid 5591
2024-08-13 16:22:20.462  - info: hm-rpc.0 (5004) binrpc -> 192.168.178.12:8701/ init ["xmlrpc_bin://192.168.178.10:18701",""]
2024-08-13 16:22:20.481  - error: hm-rpc.0 (5004) Cannot call init: [xmlrpc_bin://192.168.178.10:18701, ""] Socket closed before the connection was established
2024-08-13 16:22:20.542  - info: hm-rpc.0 (5004) terminating
2024-08-13 16:22:20.544  - info: hm-rpc.0 (5004) Terminated (NO_ERROR): Without reason
2024-08-13 16:22:21.115  - info: host.iobroker-pi instance system.adapter.hm-rpc.0 terminated with code 0 (NO_ERROR)
2024-08-13 16:22:23.573  - error: hm-rega.0 (1231) CCU 192.168.178.12 unreachable
2024-08-13 16:22:21.116  - info: host.iobroker-pi Restart adapter system.adapter.hm-rpc.0 because enabled
2024-08-13 16:22:25.483  - info: hm-rpc.1 (5590) starting. Version 1.17.0 in /opt/iobroker/node_modules/iobroker.hm-rpc, node: v20.16.0, js-controller: 5.0.19
2024-08-13 16:22:25.516  - info: hm-rpc.2 (5591) starting. Version 1.17.0 in /opt/iobroker/node_modules/iobroker.hm-rpc, node: v20.16.0, js-controller: 5.0.19
2024-08-13 16:22:25.834  - info: hm-rpc.1 (5590) xmlrpc server is trying to listen on 192.168.178.10:12001
2024-08-13 16:22:25.835  - info: hm-rpc.1 (5590) xmlrpc client is trying to connect to 192.168.178.12:2001/ with ["http://192.168.178.10:12001","iobroker-pi:hm-rpc.1:b7e0bbb00b214da627cd2ac33e1e6a94"]
2024-08-13 16:22:25.863  - info: hm-rpc.2 (5591) xmlrpc server is trying to listen on 192.168.178.10:12010
2024-08-13 16:22:25.865  - info: hm-rpc.2 (5591) xmlrpc client is trying to connect to 192.168.178.12:2010/ with ["http://192.168.178.10:12010","iobroker-pi:hm-rpc.2:53dc961ed27d3c18a140cba29ed780cc"]

[DJMarc75]

@wibear sagte in pivCCU nach Update node.js nicht erreichbar:

Ist es besser?

Wie Du vielleicht selbst siehst - nein ;)

[Homoran]

@djmarc75 sagte in pivCCU nach Update node.js nicht erreichbar:

@wibear sagte in pivCCU nach Update node.js nicht erreichbar:

Ist es besser?

Wie Du vielleicht selbst siehst - nein ;)

jetzt, ja!

im ersten hab ich nicht alle versteckten code-tags finden und fixen können

EDIT: Jetzt aber!

[wibear]

@thomas-braun sagte in pivCCU nach Update node.js nicht erreichbar:

Controller "js-controller": 6.0.9 , installed 5.0.19 [Updatable]

ausgeführt