Wasserzähler - Version 2 - all-in-device

Xsev

@jomjol Ich hatte noch einen alten ESP mit defekter Cam rumliegen, ich hab jetzt mal das alte Board genommen mit neuer Cam. Laut Log hat dieser ESP die 64Mbit aber der Fehler bleibt der selbe. Kurz vor Logende meldet er folgendes:

14:04:37.130 -> 14:04:37.130 -> Guru Meditation Error: Core  0 panic'ed (LoadProhibited). Exception was unhandled.
14:04:37.130 -> Core 0 register dump:
14:04:37.130 -> PC      : 0x400ef308  PS      : 0x00060530  A0      : 0x8018c5ca  A1      : 0x3fff9fd0  
14:04:37.130 -> A2      : 0x00000780  A3      : 0x3ffc3c68  A4      : 0x00000280  A5      : 0x00000780  
14:04:37.130 -> A6      : 0x00000001  A7      : 0x000001e0  A8      : 0x00000000  A9      : 0x3f82c168  
14:04:37.130 -> A10     : 0x00000000  A11     : 0x3f92ddd8  A12     : 0x00004d80  A13     : 0x00000001  
14:04:37.130 -> A14     : 0x3ffc35ac  A15     : 0x3fff9ef0  SAR     : 0x0000001a  EXCCAUSE: 0x0000001c  
14:04:37.130 -> EXCVADDR: 0x00000000  LBEG    : 0x4008bed5  LEND    : 0x4008bee5  LCOUNT  : 0xffffffff  
14:04:37.130 -> 
14:04:37.130 -> ELF file SHA256: 49d2944a34ee25eb
14:04:37.130 -> Backtrace: 0x400ef305:0x3fff9fd0 0x4018c5c7:0x3fffa040 0x4018c64e:0x3fffa080 0x40189d89:0x3fffa110 0x400f13a2:0x3fffa1c0

Das ganze Log:

14:04:15.068 -> Rebooting...
14:04:15.068 -> ets Jun  8 2016 00:22:57
14:04:15.068 -> 
14:04:15.068 -> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
14:04:15.068 -> configsip: 0, SPIWP:0xee
14:04:15.068 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
14:04:15.068 -> mode:DIO, clock div:2
14:04:15.068 -> load:0x3fff0030,len:4
14:04:15.068 -> load:0x3fff0034,len:7248
14:04:15.068 -> ho 0 tail 12 room 4
14:04:15.068 -> load:0x40078000,len:13856
14:04:15.068 -> load:0x40080400,len:4052
14:04:15.068 -> entry 0x40080688
14:04:15.068 -> [0;32mI (31) boot: ESP-IDF 3.40100.200827 2nd stage bootloader[0m
14:04:15.068 -> [0;32mI (31) boot: compile time 18:56:57[0m
14:04:15.068 -> [0;32mI (31) boot: chip revision: 1[0m
14:04:15.068 -> [0;32mI (34) boot_comm: chip revision: 1, min. bootloader chip revision: 0[0m
14:04:15.068 -> [0;32mI (41) boot.esp32: SPI Speed      : 40MHz[0m
14:04:15.068 -> [0;32mI (46) boot.esp32: SPI Mode       : DIO[0m
14:04:15.068 -> [0;32mI (51) boot.esp32: SPI Flash Size : 4MB[0m
14:04:15.068 -> [0;32mI (55) boot: Enabling RNG early entropy source...[0m
14:04:15.068 -> [0;32mI (61) boot: Partition Table:[0m
14:04:15.068 -> [0;32mI (64) boot: ## Label            Usage          Type ST Offset   Length[0m
14:04:15.068 -> [0;32mI (71) boot:  0 nvs              WiFi data        01 02 00009000 00004000[0m
14:04:15.068 -> [0;32mI (79) boot:  1 otadata          OTA data         01 00 0000d000 00002000[0m
14:04:15.068 -> [0;32mI (86) boot:  2 phy_init         RF data          01 01 0000f000 00001000[0m
14:04:15.068 -> [0;32mI (94) boot:  3 ota_0            OTA app          00 10 00010000 001db000[0m
14:04:15.068 -> [0;32mI (101) boot:  4 ota_1            OTA app          00 11 001f0000 001db000[0m
14:04:15.068 -> [0;32mI (109) boot: End of partition table[0m
14:04:15.068 -> [0;32mI (113) boot_comm: chip revision: 1, min. application chip revision: 0[0m
14:04:15.068 -> [0;32mI (120) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x51048 (331848) map[0m
14:04:15.224 -> [0;32mI (273) esp_image: segment 1: paddr=0x00061070 vaddr=0x3ffb0000 size=0x0504c ( 20556) load[0m
14:04:15.224 -> [0;32mI (283) esp_image: segment 2: paddr=0x000660c4 vaddr=0x40080000 size=0x00404 (  1028) load[0m
14:04:15.224 -> [0;32mI (284) esp_image: segment 3: paddr=0x000664d0 vaddr=0x40080404 size=0x09b48 ( 39752) load[0m
14:04:15.224 -> [0;32mI (310) esp_image: segment 4: paddr=0x00070020 vaddr=0x400d0020 size=0x122ec8 (1191624) map[0m
14:04:15.718 -> [0;32mI (826) esp_image: segment 5: paddr=0x00192ef0 vaddr=0x40089f4c size=0x12c68 ( 76904) load[0m
14:04:16.357 -> [0;32mI (880) boot: Loaded app from partition at offset 0x10000[0m
14:04:16.357 -> [0;32mI (880) boot: Disabling RNG early entropy source...[0m
14:04:16.357 -> [0;32mI (881) psram: This chip is ESP32-D0WD[0m
14:04:16.357 -> [0;32mI (885) spiram: Found 64MBit SPI RAM device[0m
14:04:16.357 -> [0;32mI (890) spiram: SPI RAM mode: flash 40m sram 40m[0m
14:04:16.357 -> [0;32mI (895) spiram: PSRAM initialized, cache is in low/high (2-core) mode.[0m
14:04:16.357 -> [0;32mI (903) cpu_start: Pro cpu up.[0m
14:04:16.357 -> [0;32mI (906) cpu_start: Application information:[0m
14:04:16.357 -> [0;32mI (911) cpu_start: Project name:     esp32cam-server-only[0m
14:04:16.357 -> [0;32mI (917) cpu_start: App version:      0.0.9.3[0m
14:04:16.357 -> [0;32mI (922) cpu_start: Compile time:     Sep 25 2021 18:55:36[0m
14:04:16.357 -> [0;32mI (928) cpu_start: ELF file SHA256:  49d2944a34ee25eb...[0m
14:04:16.357 -> [0;32mI (934) cpu_start: ESP-IDF:          3.40100.200827[0m
14:04:16.357 -> [0;32mI (940) cpu_start: Starting app cpu, entry point is 0x40081cf0[0m
14:04:16.357 -> [0;32mI (931) cpu_start: App cpu up.[0m
14:04:16.841 -> [0;32mI (1837) spiram: SPI SRAM memory test OK[0m
14:04:16.841 -> [0;32mI (1838) heap_init: Initializing. RAM available for dynamic allocation:[0m
14:04:16.841 -> [0;32mI (1838) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM[0m
14:04:16.841 -> [0;32mI (1844) heap_init: At 3FFC2A08 len 0001D5F8 (117 KiB): DRAM[0m
14:04:16.841 -> [0;32mI (1851) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM[0m
14:04:16.841 -> [0;32mI (1857) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM[0m
14:04:16.841 -> [0;32mI (1864) heap_init: At 4009CBB4 len 0000344C (13 KiB): IRAM[0m
14:04:16.841 -> [0;32mI (1870) cpu_start: Pro cpu start user code[0m
14:04:16.841 -> [0;32mI (1875) spiram: Adding pool of 4096K of external SPI memory to heap allocator[0m
14:04:16.841 -> [0;32mI (1900) spi_flash: detected chip: generic[0m
14:04:16.841 -> [0;32mI (1901) spi_flash: flash io: dio[0m
14:04:16.841 -> [0;32mI (1901) cpu_start: Starting scheduler on PRO CPU.[0m
14:04:16.841 -> [0;32mI (0) cpu_start: Starting scheduler on APP CPU.[0m
14:04:16.841 -> [0;32mI (1909) spiram: Reserving pool of 32K of internal memory for DMA/internal allocations[0m
14:04:16.841 -> Do Reset Camera
14:04:16.841 -> [0;32mI (1919) gpio: GPIO[32]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 [0m
14:04:18.823 -> Init Camera
14:04:18.823 -> [0;32mI (3929) gpio: GPIO[5]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3929) gpio: GPIO[18]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3929) gpio: GPIO[19]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3939) gpio: GPIO[21]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3949) gpio: GPIO[22]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3959) gpio: GPIO[23]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3969) gpio: GPIO[25]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3979) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3989) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3999) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (4009) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (4019) sccb: pin_sda 26 pin_scl 27
14:04:18.958 -> [0m
14:04:18.958 -> [0;32mI (4019) gpio: GPIO[32]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 [0m
14:04:19.098 -> [0;32mI (4169) camera: Detected OV2640 camera[0m
14:04:19.098 -> [0;32mI (4179) camera: Allocating 1 frame buffers (150 KB total)[0m
14:04:19.098 -> [0;32mI (4189) camera: Allocating 150 KB frame buffer in OnBoard RAM[0m
14:04:19.694 -> [0;32mI (4789) main: Using SDMMC peripheral[0m
14:04:19.788 -> Name: SN64G
14:04:19.788 -> Type: SDHC/SDXC
14:04:19.788 -> Speed: 20 MHz
14:04:19.788 -> Size: 60906MB
14:04:19.788 -> [0;32mI (4849) server_ota: Start CheckOTAUpdateCheck ...[0m
14:04:19.788 -> Start CheckOTAUpdateCheck ...
14:04:19.788 -> [0;32mI (4859) server_ota: SHA-256 for the partition table: : 9d4a2809ae90fb20709a8ca3dd3ac3462e1e73286bcd31b689060c91de06fa3a[0m
14:04:19.835 -> [0;32mI (4919) server_ota: SHA-256 for bootloader: : ee8b22523ca2a6f08e0e01e2e6dd2ae40f0a13f93d5c02794b19cfca199b3e9e[0m
14:04:20.491 -> [0;32mI (5559) server_ota: SHA-256 for current firmware: : dc1319e0f2d427d7bc8d303fa98e0456e09c555804634127bb0960ca1cb42b6a[0m
14:04:20.491 -> CheckOTAUpdate Partition: ESP_OK
14:04:20.538 -> open config file /sdcard/wlan.ini in mode r
14:04:20.538 -> file loaded
14:04:20.538 -> 
14:04:20.538 -> WLan: Rocket, XXXXXXXXXXXXX
14:04:20.538 -> Hostename: Watermeter13
14:04:20.538 -> I (5609) wifi:wifi driver task: 3ffd9cc4, prio:23, stack:6656, core=0
14:04:20.538 -> [0;32mI (5609) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE[0m
14:04:20.538 -> [0;32mI (5609) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE[0m
14:04:20.538 -> I (5639) wifi:wifi firmware version: 3ea4c76
14:04:20.585 -> I (5639) wifi:config NVS flash: enabled
14:04:20.585 -> I (5639) wifi:config nano formating: disabled
14:04:20.585 -> I (5639) wifi:Init dynamic tx buffer num: 32
14:04:20.585 -> I (5649) wifi:Init data frame dynamic rx buffer num: 32
14:04:20.585 -> I (5649) wifi:Init management frame dynamic rx buffer num: 32
14:04:20.585 -> I (5659) wifi:Init management short buffer num: 32
14:04:20.585 -> I (5659) wifi:Init static tx buffer num: 16
14:04:20.585 -> I (5669) wifi:Init static rx buffer size: 1600
14:04:20.585 -> I (5669) wifi:Init static rx buffer num: 10
14:04:20.585 -> I (5669) wifi:Init dynamic rx buffer num: 32
14:04:20.721 -> [0;32mI (5769) phy: phy_version: 4180, cb3948e, Sep 12 2019, 16:39:13, 0, 0[0m
14:04:20.721 -> I (5769) wifi:mode : sta (9c:9c:1f:c9:24:34)
14:04:20.721 -> [0;32mI (5769) BLINK: Blinken - start[0m
14:04:20.721 -> [0;32mI (5779) wifi station: wifi_init_sta finished.[0m
14:04:20.815 -> I (5899) wifi:new:<3,0>, old:<1,0>, ap:<255,255>, sta:<3,0>, prof:1
14:04:20.815 -> I (5899) wifi:state: init -> auth (b0)
14:04:20.815 -> I (5919) wifi:state: auth -> assoc (0)
14:04:20.862 -> I (5929) wifi:state: assoc -> run (10)
14:04:20.862 -> I (5959) wifi:connected with Rocket, aid = 2, channel 3, BW20, bssid = e0:63:da:74:3e:f2
14:04:20.909 -> I (5959) wifi:security: WPA2-PSK, phy: bgn, rssi: -72
14:04:20.909 -> I (5969) wifi:pm start, type: 1
14:04:20.909 -> 
14:04:20.909 -> [0;32mI (5979) BLINK: Blinken - done[0m
14:04:20.956 -> I (6019) wifi:AP's beacon interval = 102400 us, DTIM period = 1
14:04:21.518 -> [0;32mI (6599) esp_netif_handlers: sta ip: 192.168.13.206, mask: 255.255.255.0, gw: 192.168.13.1[0m
14:04:21.518 -> [0;32mI (6599) wifi station: got ip:192.168.13.206[0m
14:04:21.518 -> [0;32mI (6599) BLINK: Blinken - start[0m
14:04:21.518 -> [0;32mI (6609) wifi station: connected to ap SSID:Rocket password:XXXXXXXXXXXXX[0m
14:04:21.518 -> main: sleep for : 200ms
14:04:23.514 -> [0;32mI (8619) sntp: Time is not set yet. Connecting to WiFi and getting time over NTP.[0m
14:04:23.561 -> [0;32mI (8619) sntp: Initializing SNTP[0m
14:04:23.561 -> [0;32mI (8619) sntp: Waiting for system time to be set... (1/10)[0m
14:04:25.525 -> [0;32mI (10619) sntp: Waiting for system time to be set... (2/10)[0m
14:04:27.593 -> TimeZone set to CET-1CEST,M3.5.0,M10.5.0/3
14:04:27.593 -> Logfile opened: /sdcard/log/message/log_2022-03-20.txt
14:04:27.593 -> [0;32mI (12629) sntp: The current date/time in Berlin is: Sun Mar 20 14:04:29 2022[0m
14:04:27.593 -> [0;32mI (12629) sntp: The current date/time in Berlin is: 2022-03-20_14:04[0m
14:04:27.593 -> timeist 20220320-140429
14:04:27.593 -> Logfile opened: /sdcard/log/message/log_2022-03-20.txt
14:04:27.593 -> Logfile opened: /sdcard/log/message/log_2022-03-20.txt
14:04:27.593 -> Logfile opened: /sdcard/log/message/log_2022-03-20.txt
14:04:27.593 -> time 20220320-140429
14:04:27.593 -> main: sleep for : 200ms
14:04:29.619 -> [0;32mI (14659) server-main: Starting server on port: '80'[0m
14:04:29.619 -> [0;32mI (14659) server-main: Registering URI handlers[0m
14:04:29.619 -> [0;32mI (14659) server_tflite: server_part_camera - Registering URI handlers[0m
14:04:29.619 -> [0;32mI (14659) server_ota: server_ota - Registering URI handlers[0m
14:04:29.619 -> [0;32mI (14669) server_GPIO: start GpioHandler[0m
14:04:29.619 -> [0;32mI (14669) server_GPIO: register GPIO Uri[0m
14:04:29.619 -> [0;32mI (14679) server_GPIO: server_GPIO - Registering URI handlers[0m
14:04:29.619 -> vor reg server main
14:04:29.619 -> vor dotautostart
14:04:29.619 -> task_autodoFlow: start

14:04:29.619 -> open config file /sdcard/config/config.ini in mode r
14:04:29.619 -> [MakeImage]
14:04:29.619 -> Start ReadParameter ([MakeImage]
14:04:29.619 -> )
14:04:29.619 -> ;LogImageLocation = /log/source
14:04:29.619 -> WaitBeforeTakingPicture = 5
14:04:29.619 -> ;LogfileRetentionInDays = 15
14:04:29.619 -> Brightness = -2
14:04:29.619 -> ;Contrast = 0
14:04:29.619 -> ;Saturation = 0
14:04:29.619 -> ImageQuality = 5
14:04:29.619 -> ImageSize = VGA
14:04:29.619 -> FixedExposure = false
14:04:29.619 -> 
14:04:29.619 -> [Alignment]
14:04:31.563 -> Start ReadParameter ([Alignment])
14:04:31.563 -> InitialRotate = 179
14:04:31.563 -> InitialMirror = false
14:04:31.563 -> SearchFieldX = 20
14:04:31.563 -> SearchFieldY = 20
14:04:31.563 -> AlignmentAlgo = Default
14:04:31.563 -> FlipImageSize = false
14:04:31.563 -> /config/ref0.jpg 103 271
14:04:31.563 -> /config/ref1.jpg 442 142
14:04:31.563 -> 
14:04:31.563 -> [Digits]
14:04:31.563 -> Start ReadParameter ([Digits])
14:04:31.563 -> Model = /config/dig1210s2q.tflite
14:04:31.563 -> ;LogImageLocation = /log/digit
14:04:31.563 -> ;LogfileRetentionInDays = 3
14:04:31.563 -> ModelInputSize = 20 32
14:04:31.563 -> main.dig1 294 126 30 54
14:04:31.563 -> GetGENERAL - GENERAL main - roi dig1
14:04:31.563 -> main.dig2 343 126 30 54
14:04:31.563 -> GetGENERAL - GENERAL main - roi dig2
14:04:31.563 -> main.dig3 391 126 30 54
14:04:31.563 -> GetGENERAL - GENERAL main - roi dig3
14:04:31.563 -> 
14:04:31.563 -> [Analog]
14:04:31.563 -> Start ReadParameter ([Analog])
14:04:31.563 -> Model = /config/ana0700s1lq.tflite
14:04:31.563 -> ;LogImageLocation = /log/analog
14:04:31.563 -> ;LogfileRetentionInDays = 3
14:04:31.563 -> ModelInputSize = 32 32
14:04:31.563 -> ExtendedResolution = true
14:04:31.563 -> main.ana1 432 230 92 92
14:04:31.563 -> GetGENERAL - GENERAL main - roi ana1
14:04:31.563 -> main.ana2 379 332 92 92
14:04:31.563 -> GetGENERAL - GENERAL main - roi ana2
14:04:31.563 -> main.ana3 283 374 92 92
14:04:31.563 -> GetGENERAL - GENERAL main - roi ana3
14:04:31.563 -> main.ana4 155 328 92 92
14:04:31.563 -> GetGENERAL - GENERAL main - roi ana4
14:04:31.563 -> 
14:04:31.563 -> [PostProcessing]
14:04:31.563 -> Start ReadParameter ([PostProcessing])
14:04:31.563 -> Anzahl NUMBERS: 1 - DIGITS: 1, ANALOG: 1
14:04:31.563 -> Number main, Anz DIG: 3, Anz ANA 4
14:04:31.563 -> main.DecimalShift = 0
14:04:31.563 -> PreValueUse = true
14:04:31.563 -> PreValueAgeStartup = 720
14:04:31.563 -> AllowNegativeRates = false
14:04:31.563 -> main.MaxRateValue = 0.1
14:04:31.563 -> ErrorMessage = true
14:04:31.563 -> CheckDigitIncreaseConsistency = true
14:04:31.563 -> 
14:04:31.563 -> ;[MQTT]
14:04:31.563 -> Read Zeile Prevalue.ini: 2020-11-30_12-02-22
14:04:31.563 -> 42.013401
14:04:31.563 -> TIME: 120, 10, 0, 1, 1, 5
14:04:31.563 -> Read: ;Uri = mqtt://IP-ADRESS:1883
14:04:31.563 -> Read: ;MainTopic = wasserzaehler
14:04:31.563 -> Read: ;ClientID = wasser
14:04:31.563 -> Read: ;user = USERNAME
14:04:31.563 -> Read: ;password = PASSWORD
14:04:31.563 -> Read: 
14:04:31.563 -> Read: ;[GPIO]
14:04:31.563 -> Read: ;MainTopicMQTT = wasserzaehler/GPIO
14:04:31.563 -> Read: ;IO0 = input disabled 10 false false 
14:04:31.563 -> Read: ;IO1 = input disabled 10 false false 
14:04:31.563 -> Read: ;IO3 = input disabled 10 false false 
14:04:31.563 -> Read: ;IO4 = built-in-led disabled 10 false false 
14:04:31.563 -> Read: ;IO12 = input-pullup disabled 10 false false 
14:04:31.563 -> Read: ;IO13 = input-pullup disabled 10 false false 
14:04:31.563 -> Read: 
14:04:31.563 -> Read: [AutoTimer]
14:04:31.563 -> Start ReadParameter ([AutoTimer]
14:04:31.563 -> )
14:04:31.563 -> AutoStart = true
14:04:31.563 -> Intervall = 4.85
14:04:31.563 -> 
14:04:31.563 -> [Debug]
14:04:31.563 -> Start ReadParameter ([Debug])
14:04:31.563 -> Logfile = false
14:04:31.563 -> LogfileRetentionInDays = 3
14:04:31.563 -> 
14:04:31.563 -> [System]
14:04:31.563 -> Start ReadParameter ([System])
14:04:31.563 -> TimeZone = CET-1CEST,M3.5.0,M10.5.0/3
14:04:31.563 -> TimeZone set to CET-1CEST,M3.5.0,M10.5.0/3
14:04:31.563 -> ;TimeServer = undefined
14:04:31.563 -> ;AutoAdjustSummertime = false
14:04:31.563 -> ;Hostname = undefined
14:04:31.563 -> SetupMode = true
14:04:31.563 -> END OF FILE
14:04:31.563 -> *************** Start GPIOHandler_Init *****************
14:04:31.563 -> [0;32mI (16519) server_GPIO: read GPIO config and init GPIO[0m
14:04:31.563 -> open config file /sdcard/config/config.ini in mode r
14:04:31.563 -> [MakeImage]
14:04:31.563 -> ;LogImageLocation = /log/source
14:04:31.563 -> WaitBeforeTakingPicture = 5
14:04:31.563 -> ;LogfileRetentionInDays = 15
14:04:31.563 -> Brightness = -2
14:04:31.563 -> ;Contrast = 0
14:04:31.563 -> ;Saturation = 0
14:04:31.563 -> ImageQuality = 5
14:04:31.563 -> ImageSize = VGA
14:04:31.563 -> FixedExposure = false
14:04:31.563 -> 
14:04:31.563 -> [Alignment]
14:04:31.563 -> InitialRotate = 179
14:04:31.563 -> InitialMirror = false
14:04:31.563 -> SearchFieldX = 20
14:04:31.563 -> SearchFieldY = 20
14:04:31.563 -> AlignmentAlgo = Default
14:04:31.563 -> FlipImageSize = false
14:04:31.563 -> /config/ref0.jpg 103 271
14:04:31.563 -> /config/ref1.jpg 442 142
14:04:31.563 -> 
14:04:31.563 -> [Digits]
14:04:31.563 -> Model = /config/dig1210s2q.tflite
14:04:31.563 -> ;LogImageLocation = /log/digit
14:04:31.563 -> ;LogfileRetentionInDays = 3
14:04:31.563 -> ModelInputSize = 20 32
14:04:31.563 -> main.dig1 294 126 30 54
14:04:31.563 -> main.dig2 343 126 30 54
14:04:31.563 -> main.dig3 391 126 30 54
14:04:31.563 -> 
14:04:31.563 -> [Analog]
14:04:31.563 -> Model = /config/ana0700s1lq.tflite
14:04:31.563 -> ;LogImageLocation = /log/analog
14:04:31.563 -> ;LogfileRetentionInDays = 3
14:04:31.563 -> ModelInputSize = 32 32
14:04:31.563 -> ExtendedResolution = true
14:04:31.563 -> main.ana1 432 230 92 92
14:04:31.563 -> main.ana2 379 332 92 92
14:04:31.563 -> [0;32mI (16609) BLINK: Blinken - done[0m
14:04:31.563 -> main.ana3 283 374 92 92
14:04:31.563 -> main.ana4 155 328 92 92
14:04:31.563 -> 
14:04:31.563 -> [PostProcessing]
14:04:31.563 -> main.DecimalShift = 0
14:04:31.563 -> PreValueUse = true
14:04:31.563 -> PreValueAgeStartup = 720
14:04:31.563 -> AllowNegativeRates = false
14:04:31.563 -> main.MaxRateValue = 0.1
14:04:31.563 -> ErrorMessage = true
14:04:31.563 -> CheckDigitIncreaseConsistency = true
14:04:31.563 -> 
14:04:31.563 -> ;[MQTT]
14:04:31.563 -> ;Uri = mqtt://IP-ADRESS:1883
14:04:31.563 -> ;MainTopic = wasserzaehler
14:04:31.563 -> ;ClientID = wasser
14:04:31.563 -> ;user = USERNAME
14:04:31.563 -> ;password = PASSWORD
14:04:31.563 -> 
14:04:31.563 -> ;[GPIO]
14:04:31.563 -> ;MainTopicMQTT = wasserzaehler/GPIO
14:04:31.563 -> ;IO0 = input disabled 10 false false 
14:04:31.563 -> ;IO1 = input disabled 10 false false 
14:04:31.563 -> ;IO3 = input disabled 10 false false 
14:04:31.563 -> ;IO4 = built-in-led disabled 10 false false 
14:04:31.610 -> ;IO12 = input-pullup disabled 10 false false 
14:04:31.610 -> ;IO13 = input-pullup disabled 10 false false 
14:04:31.610 -> 
14:04:31.610 -> [AutoTimer]
14:04:31.610 -> AutoStart = true
14:04:31.610 -> Intervall = 4.85
14:04:31.610 -> 
14:04:31.610 -> [Debug]
14:04:31.610 -> Logfile = false
14:04:31.610 -> LogfileRetentionInDays = 3
14:04:31.610 -> 
14:04:31.610 -> [System]
14:04:31.610 -> TimeZone = CET-1CEST,M3.5.0,M10.5.0/3
14:04:31.610 -> ;TimeServer = undefined
14:04:31.610 -> ;AutoAdjustSummertime = false
14:04:31.610 -> ;Hostname = undefined
14:04:31.610 -> SetupMode = true
14:04:31.610 -> [0;32mI (16689) server_GPIO: GPIO init comleted, handler is disabled[0m
14:04:31.610 -> Flashdauer: 5000
14:04:37.130 -> Image loaded from memory: 0, 0, 0

14:04:37.130 -> 14:04:37.130 -> Guru Meditation Error: Core  0 panic'ed (LoadProhibited). Exception was unhandled.
14:04:37.130 -> Core 0 register dump:
14:04:37.130 -> PC      : 0x400ef308  PS      : 0x00060530  A0      : 0x8018c5ca  A1      : 0x3fff9fd0  
14:04:37.130 -> A2      : 0x00000780  A3      : 0x3ffc3c68  A4      : 0x00000280  A5      : 0x00000780  
14:04:37.130 -> A6      : 0x00000001  A7      : 0x000001e0  A8      : 0x00000000  A9      : 0x3f82c168  
14:04:37.130 -> A10     : 0x00000000  A11     : 0x3f92ddd8  A12     : 0x00004d80  A13     : 0x00000001  
14:04:37.130 -> A14     : 0x3ffc35ac  A15     : 0x3fff9ef0  SAR     : 0x0000001a  EXCCAUSE: 0x0000001c  
14:04:37.130 -> EXCVADDR: 0x00000000  LBEG    : 0x4008bed5  LEND    : 0x4008bee5  LCOUNT  : 0xffffffff  
14:04:37.130 -> 
14:04:37.130 -> ELF file SHA256: 49d2944a34ee25eb
14:04:37.130 -> Backtrace: 0x400ef305:0x3fff9fd0 0x4018c5c7:0x3fffa040 0x4018c64e:0x3fffa080 0x40189d89:0x3fffa110 0x400f13a2:0x3fffa1c0
14:04:37.130 -> 
14:04:37.130 -> Rebooting...
14:04:37.130 -> ets Jun  8 2016 00:22:57

martinschm

Hi,

ich habe gerade in meinen history Daten gesehen, das bei mir die 4 an der dritten Stelle wohl nicht richtig erkannt wird. Lauter raw Werte die ein N dort anzeigen. Mittlerweile ist der Zähler bei der 5 und dann der 6 angekommen.

Kann ich irgendwie mit anderen Trainingswerten ein Test laufen lassen ob er damit die 4 richtig erkannt hätte?

ciao
Martin

toki1973

Kann mir das jemand erklären?

JoergH

@toki1973 Was ist denn unklar? Der Zähler wird korrekt abgelesen, aber zuvor hatte er wohl mal einen höheren falschen Wert und da er nicht rückwärts zählen darf laut Deinen Einstellungen ("allow negative rates - false"), übermittelt er weiter den zuvor fälschlicherweise ermittelten, hohen Wert. Warum der mal so falsch ermittelt wurde? Keine Ahnung. Ich habe von 4 Zählern mit 3 en dauernd Probleme mit der Erkennung. Ich denke ohne eigenes Training mit den Bildern der eigenen Schrift wird es vermutlich nicht besser werden bei mir.

mameier1234

@joergh Ich denke mal die Hauptfrage ist, warum da ein Sprung zwischendurch von 390 auf 411 stattfand, obwohl das MaxRateValue auf 0,9 steht...

Das passiert bei mir auch leider immer wieder mal.. Bisher ohne Erklärung..

Xsev

@jomjol
Kannst du vielleicht bei Gelegenheit bitte nochmal über das Log schauen. Trotz anderem ESP (mit 64Mbit Psram) und jetzt auch neuer 32GB SD Karte, selbes Problem. Ich komm aus dem Dauerreboot einfach nicht raus.

@xsev sagte in Wasserzähler - Version 2 - all-in-device:

@jomjol Ich hatte noch einen alten ESP mit defekter Cam rumliegen, ich hab jetzt mal das alte Board genommen mit neuer Cam. Laut Log hat dieser ESP die 64Mbit aber der Fehler bleibt der selbe. Kurz vor Logende meldet er folgendes:

14:04:37.130 -> 14:04:37.130 -> Guru Meditation Error: Core  0 panic'ed (LoadProhibited). Exception was unhandled.
14:04:37.130 -> Core 0 register dump:
14:04:37.130 -> PC      : 0x400ef308  PS      : 0x00060530  A0      : 0x8018c5ca  A1      : 0x3fff9fd0  
14:04:37.130 -> A2      : 0x00000780  A3      : 0x3ffc3c68  A4      : 0x00000280  A5      : 0x00000780  
14:04:37.130 -> A6      : 0x00000001  A7      : 0x000001e0  A8      : 0x00000000  A9      : 0x3f82c168  
14:04:37.130 -> A10     : 0x00000000  A11     : 0x3f92ddd8  A12     : 0x00004d80  A13     : 0x00000001  
14:04:37.130 -> A14     : 0x3ffc35ac  A15     : 0x3fff9ef0  SAR     : 0x0000001a  EXCCAUSE: 0x0000001c  
14:04:37.130 -> EXCVADDR: 0x00000000  LBEG    : 0x4008bed5  LEND    : 0x4008bee5  LCOUNT  : 0xffffffff  
14:04:37.130 -> 
14:04:37.130 -> ELF file SHA256: 49d2944a34ee25eb
14:04:37.130 -> Backtrace: 0x400ef305:0x3fff9fd0 0x4018c5c7:0x3fffa040 0x4018c64e:0x3fffa080 0x40189d89:0x3fffa110 0x400f13a2:0x3fffa1c0

Das ganze Log:

14:04:15.068 -> Rebooting...
14:04:15.068 -> ets Jun  8 2016 00:22:57
14:04:15.068 -> 
14:04:15.068 -> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
14:04:15.068 -> configsip: 0, SPIWP:0xee
14:04:15.068 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
14:04:15.068 -> mode:DIO, clock div:2
14:04:15.068 -> load:0x3fff0030,len:4
14:04:15.068 -> load:0x3fff0034,len:7248
14:04:15.068 -> ho 0 tail 12 room 4
14:04:15.068 -> load:0x40078000,len:13856
14:04:15.068 -> load:0x40080400,len:4052
14:04:15.068 -> entry 0x40080688
14:04:15.068 -> [0;32mI (31) boot: ESP-IDF 3.40100.200827 2nd stage bootloader[0m
14:04:15.068 -> [0;32mI (31) boot: compile time 18:56:57[0m
14:04:15.068 -> [0;32mI (31) boot: chip revision: 1[0m
14:04:15.068 -> [0;32mI (34) boot_comm: chip revision: 1, min. bootloader chip revision: 0[0m
14:04:15.068 -> [0;32mI (41) boot.esp32: SPI Speed      : 40MHz[0m
14:04:15.068 -> [0;32mI (46) boot.esp32: SPI Mode       : DIO[0m
14:04:15.068 -> [0;32mI (51) boot.esp32: SPI Flash Size : 4MB[0m
14:04:15.068 -> [0;32mI (55) boot: Enabling RNG early entropy source...[0m
14:04:15.068 -> [0;32mI (61) boot: Partition Table:[0m
14:04:15.068 -> [0;32mI (64) boot: ## Label            Usage          Type ST Offset   Length[0m
14:04:15.068 -> [0;32mI (71) boot:  0 nvs              WiFi data        01 02 00009000 00004000[0m
14:04:15.068 -> [0;32mI (79) boot:  1 otadata          OTA data         01 00 0000d000 00002000[0m
14:04:15.068 -> [0;32mI (86) boot:  2 phy_init         RF data          01 01 0000f000 00001000[0m
14:04:15.068 -> [0;32mI (94) boot:  3 ota_0            OTA app          00 10 00010000 001db000[0m
14:04:15.068 -> [0;32mI (101) boot:  4 ota_1            OTA app          00 11 001f0000 001db000[0m
14:04:15.068 -> [0;32mI (109) boot: End of partition table[0m
14:04:15.068 -> [0;32mI (113) boot_comm: chip revision: 1, min. application chip revision: 0[0m
14:04:15.068 -> [0;32mI (120) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x51048 (331848) map[0m
14:04:15.224 -> [0;32mI (273) esp_image: segment 1: paddr=0x00061070 vaddr=0x3ffb0000 size=0x0504c ( 20556) load[0m
14:04:15.224 -> [0;32mI (283) esp_image: segment 2: paddr=0x000660c4 vaddr=0x40080000 size=0x00404 (  1028) load[0m
14:04:15.224 -> [0;32mI (284) esp_image: segment 3: paddr=0x000664d0 vaddr=0x40080404 size=0x09b48 ( 39752) load[0m
14:04:15.224 -> [0;32mI (310) esp_image: segment 4: paddr=0x00070020 vaddr=0x400d0020 size=0x122ec8 (1191624) map[0m
14:04:15.718 -> [0;32mI (826) esp_image: segment 5: paddr=0x00192ef0 vaddr=0x40089f4c size=0x12c68 ( 76904) load[0m
14:04:16.357 -> [0;32mI (880) boot: Loaded app from partition at offset 0x10000[0m
14:04:16.357 -> [0;32mI (880) boot: Disabling RNG early entropy source...[0m
14:04:16.357 -> [0;32mI (881) psram: This chip is ESP32-D0WD[0m
14:04:16.357 -> [0;32mI (885) spiram: Found 64MBit SPI RAM device[0m
14:04:16.357 -> [0;32mI (890) spiram: SPI RAM mode: flash 40m sram 40m[0m
14:04:16.357 -> [0;32mI (895) spiram: PSRAM initialized, cache is in low/high (2-core) mode.[0m
14:04:16.357 -> [0;32mI (903) cpu_start: Pro cpu up.[0m
14:04:16.357 -> [0;32mI (906) cpu_start: Application information:[0m
14:04:16.357 -> [0;32mI (911) cpu_start: Project name:     esp32cam-server-only[0m
14:04:16.357 -> [0;32mI (917) cpu_start: App version:      0.0.9.3[0m
14:04:16.357 -> [0;32mI (922) cpu_start: Compile time:     Sep 25 2021 18:55:36[0m
14:04:16.357 -> [0;32mI (928) cpu_start: ELF file SHA256:  49d2944a34ee25eb...[0m
14:04:16.357 -> [0;32mI (934) cpu_start: ESP-IDF:          3.40100.200827[0m
14:04:16.357 -> [0;32mI (940) cpu_start: Starting app cpu, entry point is 0x40081cf0[0m
14:04:16.357 -> [0;32mI (931) cpu_start: App cpu up.[0m
14:04:16.841 -> [0;32mI (1837) spiram: SPI SRAM memory test OK[0m
14:04:16.841 -> [0;32mI (1838) heap_init: Initializing. RAM available for dynamic allocation:[0m
14:04:16.841 -> [0;32mI (1838) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM[0m
14:04:16.841 -> [0;32mI (1844) heap_init: At 3FFC2A08 len 0001D5F8 (117 KiB): DRAM[0m
14:04:16.841 -> [0;32mI (1851) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM[0m
14:04:16.841 -> [0;32mI (1857) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM[0m
14:04:16.841 -> [0;32mI (1864) heap_init: At 4009CBB4 len 0000344C (13 KiB): IRAM[0m
14:04:16.841 -> [0;32mI (1870) cpu_start: Pro cpu start user code[0m
14:04:16.841 -> [0;32mI (1875) spiram: Adding pool of 4096K of external SPI memory to heap allocator[0m
14:04:16.841 -> [0;32mI (1900) spi_flash: detected chip: generic[0m
14:04:16.841 -> [0;32mI (1901) spi_flash: flash io: dio[0m
14:04:16.841 -> [0;32mI (1901) cpu_start: Starting scheduler on PRO CPU.[0m
14:04:16.841 -> [0;32mI (0) cpu_start: Starting scheduler on APP CPU.[0m
14:04:16.841 -> [0;32mI (1909) spiram: Reserving pool of 32K of internal memory for DMA/internal allocations[0m
14:04:16.841 -> Do Reset Camera
14:04:16.841 -> [0;32mI (1919) gpio: GPIO[32]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 [0m
14:04:18.823 -> Init Camera
14:04:18.823 -> [0;32mI (3929) gpio: GPIO[5]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3929) gpio: GPIO[18]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3929) gpio: GPIO[19]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3939) gpio: GPIO[21]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3949) gpio: GPIO[22]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3959) gpio: GPIO[23]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3969) gpio: GPIO[25]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3979) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3989) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (3999) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (4009) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 [0m
14:04:18.958 -> [0;32mI (4019) sccb: pin_sda 26 pin_scl 27
14:04:18.958 -> [0m
14:04:18.958 -> [0;32mI (4019) gpio: GPIO[32]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 [0m
14:04:19.098 -> [0;32mI (4169) camera: Detected OV2640 camera[0m
14:04:19.098 -> [0;32mI (4179) camera: Allocating 1 frame buffers (150 KB total)[0m
14:04:19.098 -> [0;32mI (4189) camera: Allocating 150 KB frame buffer in OnBoard RAM[0m
14:04:19.694 -> [0;32mI (4789) main: Using SDMMC peripheral[0m
14:04:19.788 -> Name: SN64G
14:04:19.788 -> Type: SDHC/SDXC
14:04:19.788 -> Speed: 20 MHz
14:04:19.788 -> Size: 60906MB
14:04:19.788 -> [0;32mI (4849) server_ota: Start CheckOTAUpdateCheck ...[0m
14:04:19.788 -> Start CheckOTAUpdateCheck ...
14:04:19.788 -> [0;32mI (4859) server_ota: SHA-256 for the partition table: : 9d4a2809ae90fb20709a8ca3dd3ac3462e1e73286bcd31b689060c91de06fa3a[0m
14:04:19.835 -> [0;32mI (4919) server_ota: SHA-256 for bootloader: : ee8b22523ca2a6f08e0e01e2e6dd2ae40f0a13f93d5c02794b19cfca199b3e9e[0m
14:04:20.491 -> [0;32mI (5559) server_ota: SHA-256 for current firmware: : dc1319e0f2d427d7bc8d303fa98e0456e09c555804634127bb0960ca1cb42b6a[0m
14:04:20.491 -> CheckOTAUpdate Partition: ESP_OK
14:04:20.538 -> open config file /sdcard/wlan.ini in mode r
14:04:20.538 -> file loaded
14:04:20.538 -> 
14:04:20.538 -> WLan: Rocket, XXXXXXXXXXXXX
14:04:20.538 -> Hostename: Watermeter13
14:04:20.538 -> I (5609) wifi:wifi driver task: 3ffd9cc4, prio:23, stack:6656, core=0
14:04:20.538 -> [0;32mI (5609) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE[0m
14:04:20.538 -> [0;32mI (5609) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE[0m
14:04:20.538 -> I (5639) wifi:wifi firmware version: 3ea4c76
14:04:20.585 -> I (5639) wifi:config NVS flash: enabled
14:04:20.585 -> I (5639) wifi:config nano formating: disabled
14:04:20.585 -> I (5639) wifi:Init dynamic tx buffer num: 32
14:04:20.585 -> I (5649) wifi:Init data frame dynamic rx buffer num: 32
14:04:20.585 -> I (5649) wifi:Init management frame dynamic rx buffer num: 32
14:04:20.585 -> I (5659) wifi:Init management short buffer num: 32
14:04:20.585 -> I (5659) wifi:Init static tx buffer num: 16
14:04:20.585 -> I (5669) wifi:Init static rx buffer size: 1600
14:04:20.585 -> I (5669) wifi:Init static rx buffer num: 10
14:04:20.585 -> I (5669) wifi:Init dynamic rx buffer num: 32
14:04:20.721 -> [0;32mI (5769) phy: phy_version: 4180, cb3948e, Sep 12 2019, 16:39:13, 0, 0[0m
14:04:20.721 -> I (5769) wifi:mode : sta (9c:9c:1f:c9:24:34)
14:04:20.721 -> [0;32mI (5769) BLINK: Blinken - start[0m
14:04:20.721 -> [0;32mI (5779) wifi station: wifi_init_sta finished.[0m
14:04:20.815 -> I (5899) wifi:new:<3,0>, old:<1,0>, ap:<255,255>, sta:<3,0>, prof:1
14:04:20.815 -> I (5899) wifi:state: init -> auth (b0)
14:04:20.815 -> I (5919) wifi:state: auth -> assoc (0)
14:04:20.862 -> I (5929) wifi:state: assoc -> run (10)
14:04:20.862 -> I (5959) wifi:connected with Rocket, aid = 2, channel 3, BW20, bssid = e0:63:da:74:3e:f2
14:04:20.909 -> I (5959) wifi:security: WPA2-PSK, phy: bgn, rssi: -72
14:04:20.909 -> I (5969) wifi:pm start, type: 1
14:04:20.909 -> 
14:04:20.909 -> [0;32mI (5979) BLINK: Blinken - done[0m
14:04:20.956 -> I (6019) wifi:AP's beacon interval = 102400 us, DTIM period = 1
14:04:21.518 -> [0;32mI (6599) esp_netif_handlers: sta ip: 192.168.13.206, mask: 255.255.255.0, gw: 192.168.13.1[0m
14:04:21.518 -> [0;32mI (6599) wifi station: got ip:192.168.13.206[0m
14:04:21.518 -> [0;32mI (6599) BLINK: Blinken - start[0m
14:04:21.518 -> [0;32mI (6609) wifi station: connected to ap SSID:Rocket password:XXXXXXXXXXXXX[0m
14:04:21.518 -> main: sleep for : 200ms
14:04:23.514 -> [0;32mI (8619) sntp: Time is not set yet. Connecting to WiFi and getting time over NTP.[0m
14:04:23.561 -> [0;32mI (8619) sntp: Initializing SNTP[0m
14:04:23.561 -> [0;32mI (8619) sntp: Waiting for system time to be set... (1/10)[0m
14:04:25.525 -> [0;32mI (10619) sntp: Waiting for system time to be set... (2/10)[0m
14:04:27.593 -> TimeZone set to CET-1CEST,M3.5.0,M10.5.0/3
14:04:27.593 -> Logfile opened: /sdcard/log/message/log_2022-03-20.txt
14:04:27.593 -> [0;32mI (12629) sntp: The current date/time in Berlin is: Sun Mar 20 14:04:29 2022[0m
14:04:27.593 -> [0;32mI (12629) sntp: The current date/time in Berlin is: 2022-03-20_14:04[0m
14:04:27.593 -> timeist 20220320-140429
14:04:27.593 -> Logfile opened: /sdcard/log/message/log_2022-03-20.txt
14:04:27.593 -> Logfile opened: /sdcard/log/message/log_2022-03-20.txt
14:04:27.593 -> Logfile opened: /sdcard/log/message/log_2022-03-20.txt
14:04:27.593 -> time 20220320-140429
14:04:27.593 -> main: sleep for : 200ms
14:04:29.619 -> [0;32mI (14659) server-main: Starting server on port: '80'[0m
14:04:29.619 -> [0;32mI (14659) server-main: Registering URI handlers[0m
14:04:29.619 -> [0;32mI (14659) server_tflite: server_part_camera - Registering URI handlers[0m
14:04:29.619 -> [0;32mI (14659) server_ota: server_ota - Registering URI handlers[0m
14:04:29.619 -> [0;32mI (14669) server_GPIO: start GpioHandler[0m
14:04:29.619 -> [0;32mI (14669) server_GPIO: register GPIO Uri[0m
14:04:29.619 -> [0;32mI (14679) server_GPIO: server_GPIO - Registering URI handlers[0m
14:04:29.619 -> vor reg server main
14:04:29.619 -> vor dotautostart
14:04:29.619 -> task_autodoFlow: start

14:04:29.619 -> open config file /sdcard/config/config.ini in mode r
14:04:29.619 -> [MakeImage]
14:04:29.619 -> Start ReadParameter ([MakeImage]
14:04:29.619 -> )
14:04:29.619 -> ;LogImageLocation = /log/source
14:04:29.619 -> WaitBeforeTakingPicture = 5
14:04:29.619 -> ;LogfileRetentionInDays = 15
14:04:29.619 -> Brightness = -2
14:04:29.619 -> ;Contrast = 0
14:04:29.619 -> ;Saturation = 0
14:04:29.619 -> ImageQuality = 5
14:04:29.619 -> ImageSize = VGA
14:04:29.619 -> FixedExposure = false
14:04:29.619 -> 
14:04:29.619 -> [Alignment]
14:04:31.563 -> Start ReadParameter ([Alignment])
14:04:31.563 -> InitialRotate = 179
14:04:31.563 -> InitialMirror = false
14:04:31.563 -> SearchFieldX = 20
14:04:31.563 -> SearchFieldY = 20
14:04:31.563 -> AlignmentAlgo = Default
14:04:31.563 -> FlipImageSize = false
14:04:31.563 -> /config/ref0.jpg 103 271
14:04:31.563 -> /config/ref1.jpg 442 142
14:04:31.563 -> 
14:04:31.563 -> [Digits]
14:04:31.563 -> Start ReadParameter ([Digits])
14:04:31.563 -> Model = /config/dig1210s2q.tflite
14:04:31.563 -> ;LogImageLocation = /log/digit
14:04:31.563 -> ;LogfileRetentionInDays = 3
14:04:31.563 -> ModelInputSize = 20 32
14:04:31.563 -> main.dig1 294 126 30 54
14:04:31.563 -> GetGENERAL - GENERAL main - roi dig1
14:04:31.563 -> main.dig2 343 126 30 54
14:04:31.563 -> GetGENERAL - GENERAL main - roi dig2
14:04:31.563 -> main.dig3 391 126 30 54
14:04:31.563 -> GetGENERAL - GENERAL main - roi dig3
14:04:31.563 -> 
14:04:31.563 -> [Analog]
14:04:31.563 -> Start ReadParameter ([Analog])
14:04:31.563 -> Model = /config/ana0700s1lq.tflite
14:04:31.563 -> ;LogImageLocation = /log/analog
14:04:31.563 -> ;LogfileRetentionInDays = 3
14:04:31.563 -> ModelInputSize = 32 32
14:04:31.563 -> ExtendedResolution = true
14:04:31.563 -> main.ana1 432 230 92 92
14:04:31.563 -> GetGENERAL - GENERAL main - roi ana1
14:04:31.563 -> main.ana2 379 332 92 92
14:04:31.563 -> GetGENERAL - GENERAL main - roi ana2
14:04:31.563 -> main.ana3 283 374 92 92
14:04:31.563 -> GetGENERAL - GENERAL main - roi ana3
14:04:31.563 -> main.ana4 155 328 92 92
14:04:31.563 -> GetGENERAL - GENERAL main - roi ana4
14:04:31.563 -> 
14:04:31.563 -> [PostProcessing]
14:04:31.563 -> Start ReadParameter ([PostProcessing])
14:04:31.563 -> Anzahl NUMBERS: 1 - DIGITS: 1, ANALOG: 1
14:04:31.563 -> Number main, Anz DIG: 3, Anz ANA 4
14:04:31.563 -> main.DecimalShift = 0
14:04:31.563 -> PreValueUse = true
14:04:31.563 -> PreValueAgeStartup = 720
14:04:31.563 -> AllowNegativeRates = false
14:04:31.563 -> main.MaxRateValue = 0.1
14:04:31.563 -> ErrorMessage = true
14:04:31.563 -> CheckDigitIncreaseConsistency = true
14:04:31.563 -> 
14:04:31.563 -> ;[MQTT]
14:04:31.563 -> Read Zeile Prevalue.ini: 2020-11-30_12-02-22
14:04:31.563 -> 42.013401
14:04:31.563 -> TIME: 120, 10, 0, 1, 1, 5
14:04:31.563 -> Read: ;Uri = mqtt://IP-ADRESS:1883
14:04:31.563 -> Read: ;MainTopic = wasserzaehler
14:04:31.563 -> Read: ;ClientID = wasser
14:04:31.563 -> Read: ;user = USERNAME
14:04:31.563 -> Read: ;password = PASSWORD
14:04:31.563 -> Read: 
14:04:31.563 -> Read: ;[GPIO]
14:04:31.563 -> Read: ;MainTopicMQTT = wasserzaehler/GPIO
14:04:31.563 -> Read: ;IO0 = input disabled 10 false false 
14:04:31.563 -> Read: ;IO1 = input disabled 10 false false 
14:04:31.563 -> Read: ;IO3 = input disabled 10 false false 
14:04:31.563 -> Read: ;IO4 = built-in-led disabled 10 false false 
14:04:31.563 -> Read: ;IO12 = input-pullup disabled 10 false false 
14:04:31.563 -> Read: ;IO13 = input-pullup disabled 10 false false 
14:04:31.563 -> Read: 
14:04:31.563 -> Read: [AutoTimer]
14:04:31.563 -> Start ReadParameter ([AutoTimer]
14:04:31.563 -> )
14:04:31.563 -> AutoStart = true
14:04:31.563 -> Intervall = 4.85
14:04:31.563 -> 
14:04:31.563 -> [Debug]
14:04:31.563 -> Start ReadParameter ([Debug])
14:04:31.563 -> Logfile = false
14:04:31.563 -> LogfileRetentionInDays = 3
14:04:31.563 -> 
14:04:31.563 -> [System]
14:04:31.563 -> Start ReadParameter ([System])
14:04:31.563 -> TimeZone = CET-1CEST,M3.5.0,M10.5.0/3
14:04:31.563 -> TimeZone set to CET-1CEST,M3.5.0,M10.5.0/3
14:04:31.563 -> ;TimeServer = undefined
14:04:31.563 -> ;AutoAdjustSummertime = false
14:04:31.563 -> ;Hostname = undefined
14:04:31.563 -> SetupMode = true
14:04:31.563 -> END OF FILE
14:04:31.563 -> *************** Start GPIOHandler_Init *****************
14:04:31.563 -> [0;32mI (16519) server_GPIO: read GPIO config and init GPIO[0m
14:04:31.563 -> open config file /sdcard/config/config.ini in mode r
14:04:31.563 -> [MakeImage]
14:04:31.563 -> ;LogImageLocation = /log/source
14:04:31.563 -> WaitBeforeTakingPicture = 5
14:04:31.563 -> ;LogfileRetentionInDays = 15
14:04:31.563 -> Brightness = -2
14:04:31.563 -> ;Contrast = 0
14:04:31.563 -> ;Saturation = 0
14:04:31.563 -> ImageQuality = 5
14:04:31.563 -> ImageSize = VGA
14:04:31.563 -> FixedExposure = false
14:04:31.563 -> 
14:04:31.563 -> [Alignment]
14:04:31.563 -> InitialRotate = 179
14:04:31.563 -> InitialMirror = false
14:04:31.563 -> SearchFieldX = 20
14:04:31.563 -> SearchFieldY = 20
14:04:31.563 -> AlignmentAlgo = Default
14:04:31.563 -> FlipImageSize = false
14:04:31.563 -> /config/ref0.jpg 103 271
14:04:31.563 -> /config/ref1.jpg 442 142
14:04:31.563 -> 
14:04:31.563 -> [Digits]
14:04:31.563 -> Model = /config/dig1210s2q.tflite
14:04:31.563 -> ;LogImageLocation = /log/digit
14:04:31.563 -> ;LogfileRetentionInDays = 3
14:04:31.563 -> ModelInputSize = 20 32
14:04:31.563 -> main.dig1 294 126 30 54
14:04:31.563 -> main.dig2 343 126 30 54
14:04:31.563 -> main.dig3 391 126 30 54
14:04:31.563 -> 
14:04:31.563 -> [Analog]
14:04:31.563 -> Model = /config/ana0700s1lq.tflite
14:04:31.563 -> ;LogImageLocation = /log/analog
14:04:31.563 -> ;LogfileRetentionInDays = 3
14:04:31.563 -> ModelInputSize = 32 32
14:04:31.563 -> ExtendedResolution = true
14:04:31.563 -> main.ana1 432 230 92 92
14:04:31.563 -> main.ana2 379 332 92 92
14:04:31.563 -> [0;32mI (16609) BLINK: Blinken - done[0m
14:04:31.563 -> main.ana3 283 374 92 92
14:04:31.563 -> main.ana4 155 328 92 92
14:04:31.563 -> 
14:04:31.563 -> [PostProcessing]
14:04:31.563 -> main.DecimalShift = 0
14:04:31.563 -> PreValueUse = true
14:04:31.563 -> PreValueAgeStartup = 720
14:04:31.563 -> AllowNegativeRates = false
14:04:31.563 -> main.MaxRateValue = 0.1
14:04:31.563 -> ErrorMessage = true
14:04:31.563 -> CheckDigitIncreaseConsistency = true
14:04:31.563 -> 
14:04:31.563 -> ;[MQTT]
14:04:31.563 -> ;Uri = mqtt://IP-ADRESS:1883
14:04:31.563 -> ;MainTopic = wasserzaehler
14:04:31.563 -> ;ClientID = wasser
14:04:31.563 -> ;user = USERNAME
14:04:31.563 -> ;password = PASSWORD
14:04:31.563 -> 
14:04:31.563 -> ;[GPIO]
14:04:31.563 -> ;MainTopicMQTT = wasserzaehler/GPIO
14:04:31.563 -> ;IO0 = input disabled 10 false false 
14:04:31.563 -> ;IO1 = input disabled 10 false false 
14:04:31.563 -> ;IO3 = input disabled 10 false false 
14:04:31.563 -> ;IO4 = built-in-led disabled 10 false false 
14:04:31.610 -> ;IO12 = input-pullup disabled 10 false false 
14:04:31.610 -> ;IO13 = input-pullup disabled 10 false false 
14:04:31.610 -> 
14:04:31.610 -> [AutoTimer]
14:04:31.610 -> AutoStart = true
14:04:31.610 -> Intervall = 4.85
14:04:31.610 -> 
14:04:31.610 -> [Debug]
14:04:31.610 -> Logfile = false
14:04:31.610 -> LogfileRetentionInDays = 3
14:04:31.610 -> 
14:04:31.610 -> [System]
14:04:31.610 -> TimeZone = CET-1CEST,M3.5.0,M10.5.0/3
14:04:31.610 -> ;TimeServer = undefined
14:04:31.610 -> ;AutoAdjustSummertime = false
14:04:31.610 -> ;Hostname = undefined
14:04:31.610 -> SetupMode = true
14:04:31.610 -> [0;32mI (16689) server_GPIO: GPIO init comleted, handler is disabled[0m
14:04:31.610 -> Flashdauer: 5000
14:04:37.130 -> Image loaded from memory: 0, 0, 0

14:04:37.130 -> 14:04:37.130 -> Guru Meditation Error: Core  0 panic'ed (LoadProhibited). Exception was unhandled.
14:04:37.130 -> Core 0 register dump:
14:04:37.130 -> PC      : 0x400ef308  PS      : 0x00060530  A0      : 0x8018c5ca  A1      : 0x3fff9fd0  
14:04:37.130 -> A2      : 0x00000780  A3      : 0x3ffc3c68  A4      : 0x00000280  A5      : 0x00000780  
14:04:37.130 -> A6      : 0x00000001  A7      : 0x000001e0  A8      : 0x00000000  A9      : 0x3f82c168  
14:04:37.130 -> A10     : 0x00000000  A11     : 0x3f92ddd8  A12     : 0x00004d80  A13     : 0x00000001  
14:04:37.130 -> A14     : 0x3ffc35ac  A15     : 0x3fff9ef0  SAR     : 0x0000001a  EXCCAUSE: 0x0000001c  
14:04:37.130 -> EXCVADDR: 0x00000000  LBEG    : 0x4008bed5  LEND    : 0x4008bee5  LCOUNT  : 0xffffffff  
14:04:37.130 -> 
14:04:37.130 -> ELF file SHA256: 49d2944a34ee25eb
14:04:37.130 -> Backtrace: 0x400ef305:0x3fff9fd0 0x4018c5c7:0x3fffa040 0x4018c64e:0x3fffa080 0x40189d89:0x3fffa110 0x400f13a2:0x3fffa1c0
14:04:37.130 -> 
14:04:37.130 -> Rebooting...
14:04:37.130 -> ets Jun  8 2016 00:22:57

jomjol

@xsev sagte in Wasserzähler - Version 2 - all-in-device:

14:04:37.130 -> Image loaded from memory: 0, 0, 0

The Problem I see is here:
14:04:37.130 -> Image loaded from memory: 0, 0, 0

This tells, that the image from the camera could not be loaded. Can you check the connection to your camera (flex band).

BorderCounter

Hallo zusammen,

mein Problem: Die vollen Kubikmeter (6) wird nicht erkannt. Raw Value: 0082N.075 (00826.075)- Alter Stand war 0082N.981 (00825.981). Durch den Sprung der vollen Kubikmeter von 825 auf 826 und die Tatsache, dass die 1-Kubikmeterstelle nicht richtig erkannt wird, ist die "neue Menge" kleiner als die "alte Menge". Wie gehe ich am besten damit um?
Ich habe Versuchsweise das Feld für die Stelle zu vergrößern, schafft aber keine Abhilfe.

zähler.jpg

JoergH

@bordercounter Das Fenster um die Ziffer 6 sieht zu groß aus. Das würde ich mal exakt anpassen, dann erkennt er die Ziffer vielleicht besser...

BorderCounter

@joergh Ich habe das Feld schon größer gemacht. als es exakt gepasst hat, war der fehler der selbe

Xsev

@bordercounter Du kannst mal mit einem anderen Erkennungsfile testen, ich hab mit den älteren Versionen teilweise bessere Ergebnisse erzielt. Da sollten 2-3 auf der SD Karte sein, evtl. gibt's die auch als Download auf Git...

markushi

Hallo zusammen,

bin zufällig auch über dieses absolut geniale Projekt gestoßen und habs mal provisorisch installiert um meinen analogen Stromzähler auszulesen:

Funktioniert 1a und was mich echt überrascht hat, ist die hohe Erkennungsqualität der Software! Aktuell logge ich so jede Stunde den Stand in meine Postgres Datenbank:

Problem für mich bei dem Ganzen: Ich habe keine 3D-Drucker! Und irgendwie finde ich keinen Shop, wo ich mir ein gedrucktes Gehäuse für das Modul bestellen könnte?!? Habt ihr einen Tipp für mich? Wollte mir deswegen ungern einen 3D-Drucker anschaffen....

Danke!

Gruß - Markus

ERLEDIGT ---> hab jetzt bei einem Online Druckdienst Gehäuse bestellt

BananaJoe

@markushi aus Pappe oder Bastelholz / Bastelkunststoffplatten aus dem Baumarkt.
Kannst du mit dem Teppichmesser zuschneiden und kleben.
Musst nur schauen woran du es hängen oder festklemmen kannst

markushi

Kann ich eigentlich was machen, um die Erkennung zu verbessern? Mir scheint es so, als ob die "6" Probleme macht:

Das wurde auch in anderen Posts hier erwähnt, dass es mit der Zahl wohl Probleme gibt!? Hat jemand einen Tipp für mich?

Xsev

@markushi Probier mal folgendes:

@xsev sagte in Wasserzähler - Version 2 - all-in-device:

@bordercounter Du kannst mal mit einem anderen Erkennungsfile testen, ich hab mit den älteren Versionen teilweise bessere Ergebnisse erzielt. Da sollten 2-3 auf der SD Karte sein, evtl. gibt's die auch als Download auf Git...

markushi

@xsev Was genau ist das Erkennungsfile? Sind das die dig... Files im config Verzeichnis?

markushi

Ich zieh die Frage zurück nachdem ich ein wenig zu Tensorflow gegooglet habe

juergi

Hallo zusammen,
auch ich bin begeistert von diesem Tool und habe mir inzwischen auch eines für meinen Wasserzähler gebaut.
Aktuell befinde ich mich im Probebetrieb.
Da ich wegen Reflektionen oft Probleme mit falscher Erkennung habe, bin ich zu der Lösung mit externen LEDs umgestiegen. 2 WS2812B sollen hier helfen. Allerdings gehen diese bei der Erstellung eines neuen Images gar nicht an!? In der Konfiguration, bei der Erstellung eines Referenzimages, allerdings schon. Ich habe nun schon einige Versuche mit geänderten Einstellungen gemacht - die Dinger bleiben aber weiter dunkel
Die GPIO12 Konfiguration sieht so aus:

Habe ich noch etwas übersehen oder mache etwas falsch?

Hat jemand eine Idee?

Gruß
Jürgen

Nachtrag: Ich habe das Gerät nun mal eine gute Stunde neben mir laufen lassen. Das ist das Ergebnis:
Ab und an gehen die LEDs tatsächlich an (2 mal in der Zeit), sonst blieben sie aus. Nach einer der beiden Beleuchtungen blieb dann die letzte der beiden LEDs einfach an - bis zum nächsten Foto. Also irgendetwas stimmt da ja noch nicht.

Hat denn niemand außer mir die externe Beleuchtung aktiviert?

Robbi12

Hallo. Hat jemand eine Druckdatei für den Gaszähler? Würde hier auch gerne auslesen.

BananaJoe

@robbi12 sagte in Wasserzähler - Version 2 - all-in-device:

Hallo. Hat jemand eine Druckdatei für den Gaszähler? Würde hier auch gerne auslesen.

wenn du verräts welchen Hersteller / Modell von Gaszähler du hast ... nicht alle haben den gleichen

NEWS

Wasserzähler - Version 2 - all-in-device

Support us

523

32.4k

81.4k

1.3m