SONOFF NSPanel mit Lovelace UI

Kuckuckmann

@skatbert
Puh, bei mir funktioniert das Blättern mit dem Skript.
Das einzige was ich komische finde, ist die Verhackung der Umlaute. @joBr99 @Armilar könnte das ein Codierungsproblem sein?

haus-automatisierung

@kuckuckmann sagte in SONOFF NSPanel mit Lovelace UI:

wurden in das Wiki auf GitHub zu übertragen. Vlt. kannst Du mal reinschauen und dies auch unter dem Video verlinken?

Gerne, habe ich als ersten Link drunter gepackt!

Andreas_Z

Hallo zusammen, Inspiriert von euren Ideen, Umsetzungen habe ich mich entschlossen mit einem ersten Panel zu starten. Gemäß Anleitung habe ich alles geflasht, konfiguriert, angelegt. Leider hänge ich nun seit einigen Tagen erfolglos an dem folgenden Fehler und komme einfach nicht weiter:
Erstellt habe ich die TS-Scripte wie in der Anleitung beschrieben, also zuerst nur die Pfade für MQTT und 0_userdata angepasst.
09:07:43.736 error javascript.0 (1008056) script.js.common.NSPanel_1 compile failed: at script.js.common.NSPanel_1:154

javascript.0	2022-09-23 09:07:43.737	error	at processImmediate (node:internal/timers:468:21)
javascript.0	2022-09-23 09:07:43.736	error	at Immediate._onImmediate (/opt/iobroker/node_modules/iobroker.javascript/main.js:1504:17)
javascript.0	2022-09-23 09:07:43.736	error	at /opt/iobroker/node_modules/iobroker.javascript/main.js:2017:17
javascript.0	2022-09-23 09:07:43.736	error	at prepareScript (/opt/iobroker/node_modules/iobroker.javascript/main.js:1990:37)
javascript.0	2022-09-23 09:07:43.736	error	at createVM (/opt/iobroker/node_modules/iobroker.javascript/main.js:1679:24)
javascript.0	2022-09-23 09:07:43.736	error	at Object.createScript (node:vm:265:10)
javascript.0	2022-09-23 09:07:43.736	error	at new Script (node:vm:100:7)
javascript.0	2022-09-23 09:07:43.736	error	SyntaxError: await is only valid in async functions and the top level bodies of modules
javascript.0	2022-09-23 09:07:43.736	error	^^^^^
javascript.0	2022-09-23 09:07:43.736	error	await Datenpunkte_anlegen();
javascript.0	2022-09-23 09:07:43.736	error	script.js.common.NSPanel_1 compile failed: at script.js.common.NSPanel_1:154

Ich komme nicht über diesen Punkt hinaus. Ich hoffe Ihr habt einen hilfreichen Tip für mich.
System:
javascript.0 v6.0.3
Node.js v16.17.0

Armilar

@andreas_z sagte in SONOFF NSPanel mit Lovelace UI:

Hallo zusammen, Inspiriert von euren Ideen, Umsetzungen habe ich mich entschlossen mit einem ersten Panel zu starten. Gemäß Anleitung habe ich alles geflasht, konfiguriert, angelegt. Leider hänge ich nun seit einigen Tagen erfolglos an dem folgenden Fehler und komme einfach nicht weiter:
Erstellt habe ich die TS-Scripte wie in der Anleitung beschrieben, also zuerst nur die Pfade für MQTT und 0_userdata angepasst.
09:07:43.736 error javascript.0 (1008056) script.js.common.NSPanel_1 compile failed: at script.js.common.NSPanel_1:154
javascript.0	2022-09-23 09:07:43.737	error	at processImmediate (node:internal/timers:468:21)
javascript.0	2022-09-23 09:07:43.736	error	at Immediate._onImmediate (/opt/iobroker/node_modules/iobroker.javascript/main.js:1504:17)
javascript.0	2022-09-23 09:07:43.736	error	at /opt/iobroker/node_modules/iobroker.javascript/main.js:2017:17
javascript.0	2022-09-23 09:07:43.736	error	at prepareScript (/opt/iobroker/node_modules/iobroker.javascript/main.js:1990:37)
javascript.0	2022-09-23 09:07:43.736	error	at createVM (/opt/iobroker/node_modules/iobroker.javascript/main.js:1679:24)
javascript.0	2022-09-23 09:07:43.736	error	at Object.createScript (node:vm:265:10)
javascript.0	2022-09-23 09:07:43.736	error	at new Script (node:vm:100:7)
javascript.0	2022-09-23 09:07:43.736	error	SyntaxError: await is only valid in async functions and the top level bodies of modules
javascript.0	2022-09-23 09:07:43.736	error	^^^^^
javascript.0	2022-09-23 09:07:43.736	error	await Datenpunkte_anlegen();
javascript.0	2022-09-23 09:07:43.736	error	script.js.common.NSPanel_1 compile failed: at script.js.common.NSPanel_1:154 
Ich komme nicht über diesen Punkt hinaus. Ich hoffe Ihr habt einen hilfreichen Tip für mich.
System:
javascript.0 v6.0.3
Node.js v16.17.0

Hmmm. Das Script scheitert aus meiner Sicht an einer Funktion "await Datenpunkte_anlegen();"

Ich kenne diese Funktion nicht. Hast du etwas erweitert?

Wenn du diesen roten Fehlerbalken bekommst, dann gibt es auf der rechten Seite auch mindestens einen roten Punkt, der den Fehler im Skript (dort auch rot unterstrichen) anzeigt. Ist da etwas rot?

Etwa so...

Die Zeilennummer ist im ioBroker keine Unterstützung. Es wird definitiv nicht die Definition dieser Konstante sein (Zeilennummer).

Andreas_Z

@armilar Leider ist kein roter Balken in dem gesamten Verlauf sichtbar, erweitert habe ich auch nichts, das Script habe ich nach Anleitung kopiert und nur den export-Part bisher angepasst:

export const config: Config = {
    panelRecvTopic: 'mqtt.1.SmartHome.NSPanel_1.tele.RESULT',       // anpassen
    panelSendTopic: 'mqtt.1.SmartHome.NSPanel_1.cmnd.CustomSend',   // anpassen
    firstScreensaverEntity: { ScreensaverEntity: "accuweather.0.Daily.Day1.Day.PrecipitationProbability", ScreensaverEntityIcon: "weather-pouring", ScreensaverEntityText: "Regen", ScreensaverEntityUnitText: "%", ScreensaverEntityIconColor: {'val_min': 0, 'val_max': 100} },
    secondScreensaverEntity: { ScreensaverEntity: "accuweather.0.Current.WindSpeed", ScreensaverEntityIcon: "weather-windy", ScreensaverEntityText: "Wind", ScreensaverEntityUnitText: "km/h", ScreensaverEntityIconColor: {'val_min': 0, 'val_max': 180} },
    thirdScreensaverEntity: { ScreensaverEntity: "accuweather.0.Current.UVIndex", ScreensaverEntityIcon: "solar-power", ScreensaverEntityText: "UV", ScreensaverEntityUnitText: "", ScreensaverEntityIconColor: {'val_min': 0, 'val_max': 9} },
    fourthScreensaverEntity: { ScreensaverEntity: "accuweather.0.Current.RelativeHumidity", ScreensaverEntityIcon: "water-percent", ScreensaverEntityText: "Luft", ScreensaverEntityUnitText: "%", ScreensaverEntityIconColor: {'val_min': 0, 'val_max': 100, 'val_best': 65} },
    alternativeScreensaverLayout: false,
    autoWeatherColorScreensaverLayout: true,
    mrIcon1ScreensaverEntity: { ScreensaverEntity: 'mqtt.1.SmartHome.NSPanel_1.stat.POWER1', ScreensaverEntityIcon: 'light-switch', ScreensaverEntityOnColor: On, ScreensaverEntityOffColor: Off  },
    mrIcon2ScreensaverEntity: { ScreensaverEntity: 'mqtt.1.SmartHome.NSPanel_1.stat.POWER2', ScreensaverEntityIcon: 'lightbulb', ScreensaverEntityOnColor: On, ScreensaverEntityOffColor: Off  },
    timeoutScreensaver: 15,
    dimmode: 20,

Armilar

@andreas_z sagte in SONOFF NSPanel mit Lovelace UI:

@armilar Leider ist kein roter Balken in dem gesamten Verlauf sichtbar, erweitert habe ich auch nichts, das Script habe ich nach Anleitung kopiert und nur den export-Part bisher angepasst:

export const config: Config = {
    panelRecvTopic: 'mqtt.1.SmartHome.NSPanel_1.tele.RESULT',       // anpassen
    panelSendTopic: 'mqtt.1.SmartHome.NSPanel_1.cmnd.CustomSend',   // anpassen
    firstScreensaverEntity: { ScreensaverEntity: "accuweather.0.Daily.Day1.Day.PrecipitationProbability", ScreensaverEntityIcon: "weather-pouring", ScreensaverEntityText: "Regen", ScreensaverEntityUnitText: "%", ScreensaverEntityIconColor: {'val_min': 0, 'val_max': 100} },
    secondScreensaverEntity: { ScreensaverEntity: "accuweather.0.Current.WindSpeed", ScreensaverEntityIcon: "weather-windy", ScreensaverEntityText: "Wind", ScreensaverEntityUnitText: "km/h", ScreensaverEntityIconColor: {'val_min': 0, 'val_max': 180} },
    thirdScreensaverEntity: { ScreensaverEntity: "accuweather.0.Current.UVIndex", ScreensaverEntityIcon: "solar-power", ScreensaverEntityText: "UV", ScreensaverEntityUnitText: "", ScreensaverEntityIconColor: {'val_min': 0, 'val_max': 9} },
    fourthScreensaverEntity: { ScreensaverEntity: "accuweather.0.Current.RelativeHumidity", ScreensaverEntityIcon: "water-percent", ScreensaverEntityText: "Luft", ScreensaverEntityUnitText: "%", ScreensaverEntityIconColor: {'val_min': 0, 'val_max': 100, 'val_best': 65} },
    alternativeScreensaverLayout: false,
    autoWeatherColorScreensaverLayout: true,
    mrIcon1ScreensaverEntity: { ScreensaverEntity: 'mqtt.1.SmartHome.NSPanel_1.stat.POWER1', ScreensaverEntityIcon: 'light-switch', ScreensaverEntityOnColor: On, ScreensaverEntityOffColor: Off  },
    mrIcon2ScreensaverEntity: { ScreensaverEntity: 'mqtt.1.SmartHome.NSPanel_1.stat.POWER2', ScreensaverEntityIcon: 'lightbulb', ScreensaverEntityOnColor: On, ScreensaverEntityOffColor: Off  },
    timeoutScreensaver: 15,
    dimmode: 20,

Neben dem Script gibt es diesen Schraubenschlüssel. Bitte mal verbose anhaken, script kompilieren und dann den Inhalt aus dem Log senden. Finde das sehr mysteriös

Andreas_Z

@armilar

javascript.0	2022-09-23 11:26:32.057	error	at processImmediate (node:internal/timers:468:21)
javascript.0	2022-09-23 11:26:32.057	error	at Immediate._onImmediate (/opt/iobroker/node_modules/iobroker.javascript/main.js:1504:17)
javascript.0	2022-09-23 11:26:32.057	error	at /opt/iobroker/node_modules/iobroker.javascript/main.js:2017:17
javascript.0	2022-09-23 11:26:32.057	error	at prepareScript (/opt/iobroker/node_modules/iobroker.javascript/main.js:1990:37)
javascript.0	2022-09-23 11:26:32.057	error	at createVM (/opt/iobroker/node_modules/iobroker.javascript/main.js:1679:24)
javascript.0	2022-09-23 11:26:32.057	error	at Object.createScript (node:vm:265:10)
javascript.0
	2022-09-23 11:26:32.057	error	at new Script (node:vm:100:7)
javascript.0	2022-09-23 11:26:32.057	error	SyntaxError: await is only valid in async functions and the top level bodies of modules
javascript.0	2022-09-23 11:26:32.057	error	^^^^^
javascript.0	2022-09-23 11:26:32.057	error	await Datenpunkte_anlegen();
javascript.0	2022-09-23 11:26:32.057	error	script.js.common.NSPanel_1 compile failed: at script.js.common.NSPanel_1:154
javascript.0	2022-09-23 11:26:32.054	info	script.js.common.NSPanel_1: TypeScript compilation successful
javascript.0	2022-09-23 11:26:29.430	info	script.js.common.NSPanel_1: compiling TypeScript source...
javascript.0	2022-09-23 11:26:29.396	debug	File /home/Javascript/common/NSPanel_1.ts change

Nachtrag: Ich habe angefangen meine anderen Scripte einmal zu deaktivieren, auf halber Strecke fing das nspanel.ts Script dann plötzlich an zu laufen, kann aber noch nicht sagen welches Script es war. Zumindest sind nun die Datenpunkte schon einmal angelegt

11:42:20.850 info javascript.0 (1013313) script.js.common.NSPanel_1: compiling TypeScript source...
11:42:21.046 info javascript.0 (1013313) script.js.common.NSPanel_1: source code did not change, using cached compilation result...
11:42:21.065 info javascript.0 (1013313) script.js.common.NSPanel_1: registered 12 subscriptions, 6 schedules, 0 messages, 0 logs and 0 file subscriptions
11:42:21.372 warn javascript.0 (1013313) at script.js.common.NSPanel_1:1185:46
11:42:21.372 warn javascript.0 (1013313) at step (script.js.common.NSPanel_1:33:23)
11:42:21.372 warn javascript.0 (1013313) at Object.next (script.js.common.NSPanel_1:14:53)
11:42:21.372 warn javascript.0 (1013313) at fulfilled (script.js.common.NSPanel_1:5:58)

Armilar

@andreas_z sagte in SONOFF NSPanel mit Lovelace UI:

@armilar

javascript.0	2022-09-23 11:26:32.057	error	at processImmediate (node:internal/timers:468:21)
javascript.0	2022-09-23 11:26:32.057	error	at Immediate._onImmediate (/opt/iobroker/node_modules/iobroker.javascript/main.js:1504:17)
javascript.0	2022-09-23 11:26:32.057	error	at /opt/iobroker/node_modules/iobroker.javascript/main.js:2017:17
javascript.0	2022-09-23 11:26:32.057	error	at prepareScript (/opt/iobroker/node_modules/iobroker.javascript/main.js:1990:37)
javascript.0	2022-09-23 11:26:32.057	error	at createVM (/opt/iobroker/node_modules/iobroker.javascript/main.js:1679:24)
javascript.0	2022-09-23 11:26:32.057	error	at Object.createScript (node:vm:265:10)
javascript.0
	2022-09-23 11:26:32.057	error	at new Script (node:vm:100:7)
javascript.0	2022-09-23 11:26:32.057	error	SyntaxError: await is only valid in async functions and the top level bodies of modules
javascript.0	2022-09-23 11:26:32.057	error	^^^^^
javascript.0	2022-09-23 11:26:32.057	error	await Datenpunkte_anlegen();
javascript.0	2022-09-23 11:26:32.057	error	script.js.common.NSPanel_1 compile failed: at script.js.common.NSPanel_1:154
javascript.0	2022-09-23 11:26:32.054	info	script.js.common.NSPanel_1: TypeScript compilation successful
javascript.0	2022-09-23 11:26:29.430	info	script.js.common.NSPanel_1: compiling TypeScript source...
javascript.0	2022-09-23 11:26:29.396	debug	File /home/Javascript/common/NSPanel_1.ts change

Bekomme immer noch nicht auf den Schirm, wo dieser Funktionsaufruf await Datenpunkte_anlegen() herkommt . Also ein Funktionsaufruf, der in einer Funktion aufgerufen wird, die nicht async ist... Und vor allem, die kein Teil dieses Scriptes ist?

Welche Version vom JS-Controller und welche NodeJS Version benutzt du?

Nachtrag - gute Idee - Die Lokalisierung des Skriptes nacheinander. Ist bestimmt diese komische Funktion drin

Andreas_Z

@armilar
javascript.0 v6.0.3
Node.js v16.17.0

Armilar

@andreas_z sagte in SONOFF NSPanel mit Lovelace UI:

@armilar
javascript.0 v6.0.3
Node.js v16.17.0

Siehe Erweiterung (Nachtrag) und wenn du diesen ominösen Funktionsaufruf gefunden hast, dann entweder "async" vor die function oder "await" rausnehmen

Beschreibe "auf halber Strecke fing das nspanel.ts Script dann plötzlich an zu laufen". Funktioniert das Panel nun oder nicht?

Wenn ich tippen müsste, dann würde ich sagen: "sehe mal in das andere Script "testansage" im global-Verzeichnis, ob das diese Funktion hat."

Andreas_Z

@armilar
Das Verursachende Script habe ich gefunden, eine Altlast aus den Anfängen mit Alexa, dieses habe ich nun deaktiviert und wird auch nicht mehr benötigt.
Auf dem Panel selbst wird leider noch nichts angezeigt, aktuell wird an mqtt.1.SmartHome.NSPanel_1.cmnd.CustomSend immer timeout~15 gesendet
Es war die Testansage

Armilar

@andreas_z sagte in SONOFF NSPanel mit Lovelace UI:

@armilar
Das Verursachende Script habe ich gefunden, eine Altlast aus den Anfängen mit Alexa, dieses habe ich nun deaktiviert und wird auch nicht mehr benötigt.
Auf dem Panel selbst wird leider noch nichts angezeigt, aktuell wird an mqtt.1.SmartHome.NSPanel_1.cmnd.CustomSend immer timeout~15 gesendet
Es war die Testansage

Das kostet dich mindestens einen Daumen nach oben

Die Nachricht ist perfekt. Jetzt haben wir wahrscheinlich noch ein Problem im mqtt.1.

Edit:

Was macht denn das Panel gerade? Waiting for content?

Kommt im mqtt.1.SmartHome.NSPanel_1.tele.RESULT etwas an?

Häufigste Ursachen:

mqtt.1. hat einen Port eingestellt, der bereits in mqtt.0. oder sonsoff.0. oder shelly.0. verwendet wird.
mqtt.1. ist falsch konfiguriert in der Instanz
berry-Driver ist nicht korrekt installiert. Dann alle Daten rauswerfen und autoexec.be neu anlegen + starten
tasmota hat die falschen mqtt Einstellungen (auch Portnummer sollte analog mqtt.1. sein)

Hier findest du ebenfalls Hinweise und Configs für mqtt.X. :
https://github.com/joBr99/nspanel-lovelace-ui/wiki/ioBroker---Basisinstallation (Punkt 4 und 6)

Andreas_Z

@armilar Daumen hoch auf jeden Fall
Waiting for content.
Als MQTT verwende ich mosquitto, hier funktioniert die Anbindung:
1663929903: New connection from 192.168.178.140:62638 on port 1883.
1663929903: New client connected from 192.168.178.140:62638 as NSPanel_1 (p2, c1, k30, u'DVES_E7EFAC').

Der IOBroker ist nur als Client konfiguriert.
Im mqtt.1.SmartHome.NSPanel_1.tele.RESULT kommt an:
{"CustomRecv":"event,startup,42,eu"}

Im MQTT kommt auch etwas an:

Armilar

@andreas_z sagte in SONOFF NSPanel mit Lovelace UI:

@armilar
Waiting for content.
Als MQTT verwende ich mosquitto, hier funktioniert die Anbindung:
1663929903: New connection from 192.168.178.140:62638 on port 1883.
1663929903: New client connected from 192.168.178.140:62638 as NSPanel_1 (p2, c1, k30, u'DVES_E7EFAC').

Der IOBroker ist nur als Client konfiguriert.
Im mqtt.1.SmartHome.NSPanel_1.tele.RESULT kommt an:
{"CustomRecv":"event,startup,42,eu"}

Im MQTT kommt auch etwas an:

Berry Driver nochmal neu gemacht? Also autoexe.be und autoexec.bec weggeworfen?

https://raw.githubusercontent.com/joBr99/nspanel-lovelace-ui/main/tasmota/autoexec.be

danach Panel restarten

und falls dann immer noch nicht funktioniert nochmal:

FlashNextion http://nspanel.pky.eu/lovelace-ui/github/nspanel-v3.4.0.tft

Das Tasmota und das Script sprechen schon miteinander. Das Nextion aber noch nicht mit Tasmota...

Andreas_Z

@armilar

14:31:31.836 CMD: FlashNextion http://nspanel.pky.eu/lovelace-ui/github/nspanel-v3.4.0.tft
14:31:31.853 MQT: SmartHome/NSPanel_1/stat/RESULT = {"FlashNextion":"Done"}
14:31:31.894 FLH: host: nspanel.pky.eu, port: 80, get: /lovelace-ui/github/nspanel-v3.4.0.tft
14:31:33.187 FLH: Send (High Speed) flash start
14:31:33.621 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 0, "time_elapsed": 0}}
14:31:34.169 FLH: host: nspanel.pky.eu, port: 80, get: /lovelace-ui/github/nspanel-v3.4.0.tft
14:31:35.294 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 90, "time_elapsed": 2}}
14:31:36.710 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 91, "time_elapsed": 3}}
14:31:39.662 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 92, "time_elapsed": 6}}
14:31:42.604 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 93, "time_elapsed": 9}}
14:31:45.691 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 94, "time_elapsed": 12}}
14:31:48.630 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 95, "time_elapsed": 15}}
14:31:51.587 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 96, "time_elapsed": 18}}
14:31:54.341 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 97, "time_elapsed": 21}}
14:31:57.284 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 98, "time_elapsed": 24}}
14:32:00.266 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 99, "time_elapsed": 27}}
14:32:00.673 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:32:06.701 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:32:06.709 NXP: Screen Initialized
14:32:06.831 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:32:06.930 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:32:06.993 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}

Keine Ahnung was da schief läuft, die autoexec.be habe ich nun zum x-ten mal erneuert (alte Dateien zuvor gelöscht), dann nspanel-v3.4.0.tft erneut geflasht, das fängt dann aber nicht bei 1% an sondern wie oben zu sehen bei 90%

00:00:00.003 HDW: ESP32-D0WD-V3 
00:00:00.088 UFS: FlashFS mounted with 292 kB free
00:00:00.182 CFG: Loaded from File, Anzahl 21
00:00:00.197 QPC: Count 1
00:00:00.423 BRY: Berry initialized, RAM used=3735 bytes
00:00:00.455 Projekt tasmota - Tasmota Version 12.1.1(tasmota)-2_0_4_1(2022.08.25 11:41:45)
00:00:00.173 NXP: Initializing Driver
00:00:00.181 BRY: Successfully loaded 'autoexec.be'
00:00:01.889 WIF: verbinden mit AP1 suppe2 Channel 6 BSSId 2C:3A:FD:A2:BE:A6 in Modus 11n als NSPanel-1-4012...
00:00:06.127 RSL: RESULT = {"CustomRecv":"event,startup,42,eu"}
00:00:06.765 WIF: verbunden
14:36:26.131 HTP: Web-Server aktiv bei NSPanel-1-4012 mit IP-Adresse 192.168.178.140
14:36:27.787 QPC: Reset
14:36:30.757 MQT: Verbindungsversuch...
14:36:30.796 MQT: verbunden
14:36:30.802 MQT: SmartHome/NSPanel_1/tele/LWT = Online (beibehalten)
14:36:30.806 MQT: SmartHome/NSPanel_1/cmnd/POWER = 
14:36:30.823 MQT: SmartHome/NSPanel_1/tele/INFO1 = {"Info1":{"Module":"NSPanel","Version":"12.1.1(tasmota)","FallbackTopic":"cmnd/NSPanel_1_fb/","GroupTopic":"SmartHome/tasmotas/cmnd/"}}
14:36:30.842 MQT: SmartHome/NSPanel_1/tele/INFO2 = {"Info2":{"WebServerMode":"Admin","Hostname":"NSPanel-1-4012","IPAddress":"192.168.178.140"}}
14:36:30.858 MQT: SmartHome/NSPanel_1/tele/INFO3 = {"Info3":{"RestartReason":"Software reset CPU","BootCount":10}}
14:36:30.863 MQT: SmartHome/NSPanel_1/stat/RESULT = {"POWER1":"OFF"}
14:36:30.867 MQT: SmartHome/NSPanel_1/stat/POWER1 = OFF
14:36:30.882 MQT: SmartHome/NSPanel_1/stat/RESULT = {"POWER2":"OFF"}
14:36:30.886 MQT: SmartHome/NSPanel_1/stat/POWER2 = OFF
14:36:32.098 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:36:32.214 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:32.258 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:32.560 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:34.949 MQT: SmartHome/NSPanel_1/tele/STATE = {"Time":"2022-09-23T14:36:34","Uptime":"0T00:00:15","UptimeSec":15,"Heap":133,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":70,"MqttCount":1,"Berry":{"HeapUsed":13,"Objects":213},"POWER1":"OFF","POWER2":"OFF","Wifi":{"AP":1,"SSId":"suppe2","BSSId":"2C:3A:FD:A2:BE:A6","Channel":6,"Mode":"11n","RSSI":86,"Signal":-57,"LinkCount":1,"Downtime":"0T00:00:06"}}
14:36:34.996 MQT: SmartHome/NSPanel_1/tele/SENSOR = {"Time":"2022-09-23T14:36:34","ANALOG":{"Temperature1":3.6},"ESP32":{"Temperature":67.8},"TempUnit":"C"}
14:36:38.352 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:36:38.473 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:38.524 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:38.581 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:44.359 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:36:44.430 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:44.476 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:44.524 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:50.335 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:36:50.452 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}

Armilar

@andreas_z sagte in SONOFF NSPanel mit Lovelace UI:

@armilar

14:31:31.836 CMD: FlashNextion http://nspanel.pky.eu/lovelace-ui/github/nspanel-v3.4.0.tft
14:31:31.853 MQT: SmartHome/NSPanel_1/stat/RESULT = {"FlashNextion":"Done"}
14:31:31.894 FLH: host: nspanel.pky.eu, port: 80, get: /lovelace-ui/github/nspanel-v3.4.0.tft
14:31:33.187 FLH: Send (High Speed) flash start
14:31:33.621 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 0, "time_elapsed": 0}}
14:31:34.169 FLH: host: nspanel.pky.eu, port: 80, get: /lovelace-ui/github/nspanel-v3.4.0.tft
14:31:35.294 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 90, "time_elapsed": 2}}
14:31:36.710 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 91, "time_elapsed": 3}}
14:31:39.662 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 92, "time_elapsed": 6}}
14:31:42.604 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 93, "time_elapsed": 9}}
14:31:45.691 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 94, "time_elapsed": 12}}
14:31:48.630 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 95, "time_elapsed": 15}}
14:31:51.587 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 96, "time_elapsed": 18}}
14:31:54.341 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 97, "time_elapsed": 21}}
14:31:57.284 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 98, "time_elapsed": 24}}
14:32:00.266 MQT: SmartHome/NSPanel_1/tele/RESULT = {"Flashing":{"complete": 99, "time_elapsed": 27}}
14:32:00.673 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:32:06.701 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:32:06.709 NXP: Screen Initialized
14:32:06.831 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:32:06.930 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:32:06.993 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}

Keine Ahnung was da schief läuft, die autoexec.be habe ich nun zum x-ten mal erneuert (alte Dateien zuvor gelöscht), dann nspanel-v3.4.0.tft erneut geflasht, das fängt dann aber nicht bei 1% an sondern wie oben zu sehen bei 90%

00:00:00.003 HDW: ESP32-D0WD-V3 
00:00:00.088 UFS: FlashFS mounted with 292 kB free
00:00:00.182 CFG: Loaded from File, Anzahl 21
00:00:00.197 QPC: Count 1
00:00:00.423 BRY: Berry initialized, RAM used=3735 bytes
00:00:00.455 Projekt tasmota - Tasmota Version 12.1.1(tasmota)-2_0_4_1(2022.08.25 11:41:45)
00:00:00.173 NXP: Initializing Driver
00:00:00.181 BRY: Successfully loaded 'autoexec.be'
00:00:01.889 WIF: verbinden mit AP1 suppe2 Channel 6 BSSId 2C:3A:FD:A2:BE:A6 in Modus 11n als NSPanel-1-4012...
00:00:06.127 RSL: RESULT = {"CustomRecv":"event,startup,42,eu"}
00:00:06.765 WIF: verbunden
14:36:26.131 HTP: Web-Server aktiv bei NSPanel-1-4012 mit IP-Adresse 192.168.178.140
14:36:27.787 QPC: Reset
14:36:30.757 MQT: Verbindungsversuch...
14:36:30.796 MQT: verbunden
14:36:30.802 MQT: SmartHome/NSPanel_1/tele/LWT = Online (beibehalten)
14:36:30.806 MQT: SmartHome/NSPanel_1/cmnd/POWER = 
14:36:30.823 MQT: SmartHome/NSPanel_1/tele/INFO1 = {"Info1":{"Module":"NSPanel","Version":"12.1.1(tasmota)","FallbackTopic":"cmnd/NSPanel_1_fb/","GroupTopic":"SmartHome/tasmotas/cmnd/"}}
14:36:30.842 MQT: SmartHome/NSPanel_1/tele/INFO2 = {"Info2":{"WebServerMode":"Admin","Hostname":"NSPanel-1-4012","IPAddress":"192.168.178.140"}}
14:36:30.858 MQT: SmartHome/NSPanel_1/tele/INFO3 = {"Info3":{"RestartReason":"Software reset CPU","BootCount":10}}
14:36:30.863 MQT: SmartHome/NSPanel_1/stat/RESULT = {"POWER1":"OFF"}
14:36:30.867 MQT: SmartHome/NSPanel_1/stat/POWER1 = OFF
14:36:30.882 MQT: SmartHome/NSPanel_1/stat/RESULT = {"POWER2":"OFF"}
14:36:30.886 MQT: SmartHome/NSPanel_1/stat/POWER2 = OFF
14:36:32.098 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:36:32.214 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:32.258 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:32.560 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:34.949 MQT: SmartHome/NSPanel_1/tele/STATE = {"Time":"2022-09-23T14:36:34","Uptime":"0T00:00:15","UptimeSec":15,"Heap":133,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":70,"MqttCount":1,"Berry":{"HeapUsed":13,"Objects":213},"POWER1":"OFF","POWER2":"OFF","Wifi":{"AP":1,"SSId":"suppe2","BSSId":"2C:3A:FD:A2:BE:A6","Channel":6,"Mode":"11n","RSSI":86,"Signal":-57,"LinkCount":1,"Downtime":"0T00:00:06"}}
14:36:34.996 MQT: SmartHome/NSPanel_1/tele/SENSOR = {"Time":"2022-09-23T14:36:34","ANALOG":{"Temperature1":3.6},"ESP32":{"Temperature":67.8},"TempUnit":"C"}
14:36:38.352 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:36:38.473 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:38.524 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:38.581 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:44.359 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:36:44.430 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:44.476 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:44.524 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}
14:36:50.335 MQT: SmartHome/NSPanel_1/tele/RESULT = {"CustomRecv":"event,startup,42,eu"}
14:36:50.452 MQT: SmartHome/NSPanel_1/stat/RESULT = {"CustomSend":"Done"}

Sieht für mich auch alles normal aus.

Was passiert, wenn du in die Tasmota-Console das Command eingibst?

CustomSend time~12:00

mqtt.1. empfängt zwar Daten, aber wie sieht es mit dem Senden aus?

Ich sag es ja ungern, aber evtl. mal den Weg ohne den Mosquitto wie beschrieben versuchen

Also nur weil in dem Datenpunkt CustomSend Daten drin stehen, heißt das noch nicht, dass dein Mosquitto die auch auf das Device bringt.

Und für den Fall das du es testest, verwende bitte nicht schon wieder den Port 1883

joBr99

Wenn FlashNextion geht, sollte das Berry Skript passen, wenn über MQTT trotzdem nichts kommt, ist es in der regel etwas mit den tasmota mqtt settings

Andreas_Z

Grundsätzlich scheint etwas über MQTT anzukommen, das Schalten von POWER1 manuell über das Objekt SmartHome/NSPanel_1/cmnd/POWER funktioniert.
Wenn ich CustomSend time~12:00 in der Konsole absende, wird aber nichts auf dem Display angezeigt.
autexec.be:

# Sonoff NSPanel Tasmota Lovelace UI Berry Driver | code by joBr99
# based on;
# Sonoff NSPanel Tasmota (Nextion with Flashing) driver | code by peepshow-21
# based on;
# Sonoff NSPanel Tasmota driver v0.47 | code by blakadder and s-hadinger

# Example Flash
# FlashNextion http://ip-address-of-your-homeassistant:8123/local/nspanel.tft
# FlashNextion http://nspanel.pky.eu/lui.tft

class Nextion : Driver

    static header = bytes('55BB')

    static flash_block_size = 4096

    var flash_mode
	var flash_start_millis
    var flash_size
    var flash_written
    var flash_buff
    var flash_offset
    var awaiting_offset
    var tcp
    var ser
    var last_per
	var url

    def split_55(b)
      var ret = []
      var s = size(b)   
      var i = s-2   # start from last-1
      while i > 0
        if b[i] == 0x55 && b[i+1] == 0xBB           
          ret.push(b[i..s-1]) # push last msg to list
          b = b[(0..i-1)]   # write the rest back to b
        end
        i -= 1
      end
      ret.push(b)
      return ret
    end

    def crc16(data, poly)
      if !poly  poly = 0xA001 end
      # CRC-16 MODBUS HASHING ALGORITHM
      var crc = 0xFFFF
      for i:0..size(data)-1
        crc = crc ^ data[i]
        for j:0..7
          if crc & 1
            crc = (crc >> 1) ^ poly
          else
            crc = crc >> 1
          end
        end
      end
      return crc
    end

	# encode using custom protocol 55 BB [payload length] [payload length] [payload] [crc] [crc]
    def encode(payload)
      var b = bytes()
      b += self.header
      b.add(size(payload), 2)   # add size as 2 bytes, little endian
      b += bytes().fromstring(payload)
      var msg_crc = self.crc16(b)
      b.add(msg_crc, 2)       # crc 2 bytes, little endian
      return b
    end

    def encodenx(payload)
        var b = bytes().fromstring(payload)
        b += bytes('FFFFFF')
        return b
    end

    def sendnx(payload)
        import string
        var payload_bin = self.encodenx(payload)
        self.ser.write(payload_bin)
        log(string.format("NXP: Nextion command sent = %s",str(payload_bin)), 3)       
    end

    def send(payload)
        var payload_bin = self.encode(payload)
        if self.flash_mode==1
            log("NXP: skipped command becuase still flashing", 3)
        else 
            self.ser.write(payload_bin)
            log("NXP: payload sent = " + str(payload_bin), 3)
        end
    end

    def write_to_nextion(b)
        self.ser.write(b)
    end

    def screeninit()
        log("NXP: Screen Initialized")
		self.sendnx("recmod=1")		
    end

    def write_block()
        
        import string
        log("FLH: Read block",3)
        while size(self.flash_buff)<self.flash_block_size && self.tcp.connected()
            if self.tcp.available()>0
                self.flash_buff += self.tcp.readbytes()
            else
                tasmota.delay(50)
                log("FLH: Wait for available...",3)
            end
        end
        log("FLH: Buff size "+str(size(self.flash_buff)),3)
        var to_write
        if size(self.flash_buff)>self.flash_block_size
            to_write = self.flash_buff[0..self.flash_block_size-1]
            self.flash_buff = self.flash_buff[self.flash_block_size..]
        else
            to_write = self.flash_buff
            self.flash_buff = bytes()
        end
        log("FLH: Writing "+str(size(to_write)),3)
        var per = (self.flash_written*100)/self.flash_size
        if (self.last_per!=per) 
            self.last_per = per
            tasmota.publish_result(string.format("{\"Flashing\":{\"complete\": %d, \"time_elapsed\": %d}}",per , (tasmota.millis()-self.flash_start_millis)/1000), "RESULT") 
        end
        if size(to_write)>0
            self.flash_written += size(to_write)
            self.ser.write(to_write)
        end
        log("FLH: Total "+str(self.flash_written),3)
        if (self.flash_written==self.flash_size)
            log("FLH: Flashing complete - Time elapsed: %d", (tasmota.millis()-self.flash_start_millis)/1000)
            self.flash_mode = 0
			self.ser = nil
			tasmota.gc()
			self.ser = serial(17, 16, 115200, serial.SERIAL_8N1)
        end

    end

    def every_100ms()
        import string
        if self.ser.available() > 0
            var msg = self.ser.read()
            if size(msg) > 0
                log(string.format("NXP: Received Raw = %s",str(msg)), 3)
                if (self.flash_mode==1)
                    var strv = msg[0..-4].asstring()
                    if string.find(strv,"comok 2")>=0
                        log("FLH: Send (High Speed) flash start")
						self.flash_start_millis = tasmota.millis()
                        #self.sendnx(string.format("whmi-wris %d,115200,res0",self.flash_size))
                        self.sendnx(string.format("whmi-wris %d,921600,res0",self.flash_size))
						self.ser = serial(17, 16, 921600, serial.SERIAL_8N1)
                    elif size(msg)==1 && msg[0]==0x08
                        log("FLH: Waiting offset...",3)
                        self.awaiting_offset = 1
                    elif size(msg)==4 && self.awaiting_offset==1
                        self.awaiting_offset = 0
                        self.flash_offset = msg.get(0,4)
                        log("FLH: Flash offset marker "+str(self.flash_offset),3)
						if self.flash_offset != 0
							self.open_url_at(self.url, self.flash_offset)
							self.flash_written = self.flash_offset
						end
                        self.write_block()
                    elif size(msg)==1 && msg[0]==0x05
                        self.write_block()
                    else
                        log("FLH: Something has gone wrong flashing display firmware ["+str(msg)+"]",2)
                    end
                else
                    var msg_list = self.split_55(msg)
                    for i:0..size(msg_list)-1
                        msg = msg_list[i]
                        if size(msg) > 0
                            if msg == bytes('000000FFFFFF88FFFFFF')
                                self.screeninit()
                            elif size(msg)>=2 && msg[0]==0x55 && msg[1]==0xBB
                                var jm = string.format("{\"CustomRecv\":\"%s\"}",msg[4..-3].asstring())
                                tasmota.publish_result(jm, "RESULT")        
                            elif msg[0]==0x07 && size(msg)==1 # BELL/Buzzer
                                tasmota.cmd("buzzer 1,1")
                            else
                                var jm = string.format("{\"nextion\":\"%s\"}",str(msg[0..-4]))
                                tasmota.publish_result(jm, "RESULT")        
                            end
                        end       
                    end
                end
            end
        end
    end      

    def begin_nextion_flash()
        self.flash_written = 0
        self.awaiting_offset = 0
        self.flash_offset = 0
        self.sendnx('DRAKJHSUYDGBNCJHGJKSHBDN')
        self.sendnx('recmod=0')
        self.sendnx('recmod=0')
        self.flash_mode = 1
        self.sendnx("connect")        
    end
    
    def open_url_at(url, pos)
		self.url = url
        import string
        var host
        var port
        var s1 = string.split(url,7)[1]
        var i = string.find(s1,":")
        var sa
        if i<0
            port = 80
            i = string.find(s1,"/")
            sa = string.split(s1,i)
            host = sa[0]
        else
            sa = string.split(s1,i)
            host = sa[0]
            s1 = string.split(sa[1],1)[1]
            i = string.find(s1,"/")
            sa = string.split(s1,i)
            port = int(sa[0])
        end
        var get = sa[1]
        log(string.format("FLH: host: %s, port: %s, get: %s",host,port,get))
        self.tcp = tcpclient()
        self.tcp.connect(host,port)
        log("FLH: Connected:"+str(self.tcp.connected()),3)
        var get_req = "GET "+get+" HTTP/1.0\r\n"
		get_req += string.format("Range: bytes=%d-\r\n", pos)
		get_req += string.format("HOST: %s:%s\r\n\r\n",host,port)
        self.tcp.write(get_req)
        var a = self.tcp.available()
        i = 1
        while a==0 && i<5
          tasmota.delay(100*i)
          tasmota.yield() 
          i += 1
          log("FLH: Retry "+str(i),3)
          a = self.tcp.available()
        end
        if a==0
            log("FLH: Nothing available to read!",3)
            return
        end
        var b = self.tcp.readbytes()
        i = 0
        var end_headers = false;
        var headers
        while i<size(b) && headers==nil
            if b[i..(i+3)]==bytes().fromstring("\r\n\r\n") 
                headers = b[0..(i+3)].asstring()
                self.flash_buff = b[(i+4)..]
            else
                i += 1
            end
        end
        #print(headers)
		# check http respose for code 200/206
        if string.find(headers,"200 OK")>0 || string.find(headers,"206 Partial Content")>0
            log("FLH: HTTP Respose is 200 OK or 206 Partial Content",3)
		else
            log("FLH: HTTP Respose is not 200 OK or 206 Partial Content",3)
			print(headers)
			return -1
        end
		# only set flash size if pos is zero
		if pos == 0
			# check http respose for content-length
			var tag = "Content-Length: "
			i = string.find(headers,tag)
			if (i>0) 
				var i2 = string.find(headers,"\r\n",i)
				var s = headers[i+size(tag)..i2-1]
				self.flash_size=int(s)
			end
			log("FLH: Flash file size: "+str(self.flash_size),3)
		end

    end

    def flash_nextion(url)
        self.flash_size = 0
        var res = self.open_url_at(url, 0)
		if res != -1
			self.begin_nextion_flash()
		end
    end

    def init()
        log("NXP: Initializing Driver")
        self.ser = serial(17, 16, 115200, serial.SERIAL_8N1)
        self.flash_mode = 0
    end

end

var nextion = Nextion()

tasmota.add_driver(nextion)

def get_current_version(cmd, idx, payload, payload_json)
	import string
	var version_of_this_script = 4
	var jm = string.format("{\"nlui_driver_version\":\"%s\"}", version_of_this_script)
	tasmota.publish_result(jm, "RESULT")
end

tasmota.add_cmd('GetDriverVersion', get_current_version)

def update_berry_driver(cmd, idx, payload, payload_json)
	def task()
		import string
		var cl = webclient()
		cl.begin(payload)
		var r = cl.GET()
		if r == 200
			print("Sucessfully downloaded nspanel-lovelace-ui berry driver")
		else
			print("Error while downloading nspanel-lovelace-ui berry driver")
		end
		r = cl.write_file("autoexec.be")
		if r < 0
			print("Error while writeing nspanel-lovelace-ui berry driver")
		else
			print("Sucessfully written nspanel-lovelace-ui berry driver")
			var s = load('autoexec.be')
			if s == true
				var jm = string.format("{\"nlui_driver_update\":\"%s\"}", "succeeded")
				tasmota.publish_result(jm, "RESULT")
			else 
				var jm = string.format("{\"nlui_driver_update\":\"%s\"}", "failed")
				tasmota.publish_result(jm, "RESULT")
			end
			
		end
	end
	tasmota.set_timer(0,task)
	tasmota.resp_cmnd_done()
end

tasmota.add_cmd('UpdateDriverVersion', update_berry_driver)

def flash_nextion(cmd, idx, payload, payload_json)
    def task()
        nextion.flash_nextion(payload)
    end
    tasmota.set_timer(0,task)
    tasmota.resp_cmnd_done()
end

def send_cmd(cmd, idx, payload, payload_json)
    nextion.sendnx(payload)
    tasmota.resp_cmnd_done()
end

def send_cmd2(cmd, idx, payload, payload_json)
    nextion.send(payload)
    tasmota.resp_cmnd_done()
end

tasmota.add_cmd('Nextion', send_cmd)
tasmota.add_cmd('CustomSend', send_cmd2)
tasmota.add_cmd('FlashNextion', flash_nextion)

MQTT-Settings:

Sonstige Einstellungen/Vorlage

{"NAME":"NSPanel","GPIO":[0,0,0,0,3872,0,0,0,0,0,32,0,0,0,0,225,0,480,224,1,0,0,0,33,0,0,0,0,0,0,0,0,0,0,4736,0],"FLAG":0,"BASE":1}

Armilar

@andreas_z sagte in SONOFF NSPanel mit Lovelace UI:

Grundsätzlich scheint etwas über MQTT anzukommen, das Schalten von POWER1 manuell über das Objekt SmartHome/NSPanel_1/cmnd/POWER funktioniert.
Wenn ich CustomSend time~12:00 in der Konsole absende, wird aber nichts auf dem Display angezeigt.
autexec.be:

# Sonoff NSPanel Tasmota Lovelace UI Berry Driver | code by joBr99
# based on;
# Sonoff NSPanel Tasmota (Nextion with Flashing) driver | code by peepshow-21
# based on;
# Sonoff NSPanel Tasmota driver v0.47 | code by blakadder and s-hadinger

# Example Flash
# FlashNextion http://ip-address-of-your-homeassistant:8123/local/nspanel.tft
# FlashNextion http://nspanel.pky.eu/lui.tft

class Nextion : Driver

    static header = bytes('55BB')

    static flash_block_size = 4096

    var flash_mode
	var flash_start_millis
    var flash_size
    var flash_written
    var flash_buff
    var flash_offset
    var awaiting_offset
    var tcp
    var ser
    var last_per
	var url

    def split_55(b)
      var ret = []
      var s = size(b)   
      var i = s-2   # start from last-1
      while i > 0
        if b[i] == 0x55 && b[i+1] == 0xBB           
          ret.push(b[i..s-1]) # push last msg to list
          b = b[(0..i-1)]   # write the rest back to b
        end
        i -= 1
      end
      ret.push(b)
      return ret
    end

    def crc16(data, poly)
      if !poly  poly = 0xA001 end
      # CRC-16 MODBUS HASHING ALGORITHM
      var crc = 0xFFFF
      for i:0..size(data)-1
        crc = crc ^ data[i]
        for j:0..7
          if crc & 1
            crc = (crc >> 1) ^ poly
          else
            crc = crc >> 1
          end
        end
      end
      return crc
    end

	# encode using custom protocol 55 BB [payload length] [payload length] [payload] [crc] [crc]
    def encode(payload)
      var b = bytes()
      b += self.header
      b.add(size(payload), 2)   # add size as 2 bytes, little endian
      b += bytes().fromstring(payload)
      var msg_crc = self.crc16(b)
      b.add(msg_crc, 2)       # crc 2 bytes, little endian
      return b
    end

    def encodenx(payload)
        var b = bytes().fromstring(payload)
        b += bytes('FFFFFF')
        return b
    end

    def sendnx(payload)
        import string
        var payload_bin = self.encodenx(payload)
        self.ser.write(payload_bin)
        log(string.format("NXP: Nextion command sent = %s",str(payload_bin)), 3)       
    end

    def send(payload)
        var payload_bin = self.encode(payload)
        if self.flash_mode==1
            log("NXP: skipped command becuase still flashing", 3)
        else 
            self.ser.write(payload_bin)
            log("NXP: payload sent = " + str(payload_bin), 3)
        end
    end

    def write_to_nextion(b)
        self.ser.write(b)
    end

    def screeninit()
        log("NXP: Screen Initialized")
		self.sendnx("recmod=1")		
    end

    def write_block()
        
        import string
        log("FLH: Read block",3)
        while size(self.flash_buff)<self.flash_block_size && self.tcp.connected()
            if self.tcp.available()>0
                self.flash_buff += self.tcp.readbytes()
            else
                tasmota.delay(50)
                log("FLH: Wait for available...",3)
            end
        end
        log("FLH: Buff size "+str(size(self.flash_buff)),3)
        var to_write
        if size(self.flash_buff)>self.flash_block_size
            to_write = self.flash_buff[0..self.flash_block_size-1]
            self.flash_buff = self.flash_buff[self.flash_block_size..]
        else
            to_write = self.flash_buff
            self.flash_buff = bytes()
        end
        log("FLH: Writing "+str(size(to_write)),3)
        var per = (self.flash_written*100)/self.flash_size
        if (self.last_per!=per) 
            self.last_per = per
            tasmota.publish_result(string.format("{\"Flashing\":{\"complete\": %d, \"time_elapsed\": %d}}",per , (tasmota.millis()-self.flash_start_millis)/1000), "RESULT") 
        end
        if size(to_write)>0
            self.flash_written += size(to_write)
            self.ser.write(to_write)
        end
        log("FLH: Total "+str(self.flash_written),3)
        if (self.flash_written==self.flash_size)
            log("FLH: Flashing complete - Time elapsed: %d", (tasmota.millis()-self.flash_start_millis)/1000)
            self.flash_mode = 0
			self.ser = nil
			tasmota.gc()
			self.ser = serial(17, 16, 115200, serial.SERIAL_8N1)
        end

    end

    def every_100ms()
        import string
        if self.ser.available() > 0
            var msg = self.ser.read()
            if size(msg) > 0
                log(string.format("NXP: Received Raw = %s",str(msg)), 3)
                if (self.flash_mode==1)
                    var strv = msg[0..-4].asstring()
                    if string.find(strv,"comok 2")>=0
                        log("FLH: Send (High Speed) flash start")
						self.flash_start_millis = tasmota.millis()
                        #self.sendnx(string.format("whmi-wris %d,115200,res0",self.flash_size))
                        self.sendnx(string.format("whmi-wris %d,921600,res0",self.flash_size))
						self.ser = serial(17, 16, 921600, serial.SERIAL_8N1)
                    elif size(msg)==1 && msg[0]==0x08
                        log("FLH: Waiting offset...",3)
                        self.awaiting_offset = 1
                    elif size(msg)==4 && self.awaiting_offset==1
                        self.awaiting_offset = 0
                        self.flash_offset = msg.get(0,4)
                        log("FLH: Flash offset marker "+str(self.flash_offset),3)
						if self.flash_offset != 0
							self.open_url_at(self.url, self.flash_offset)
							self.flash_written = self.flash_offset
						end
                        self.write_block()
                    elif size(msg)==1 && msg[0]==0x05
                        self.write_block()
                    else
                        log("FLH: Something has gone wrong flashing display firmware ["+str(msg)+"]",2)
                    end
                else
                    var msg_list = self.split_55(msg)
                    for i:0..size(msg_list)-1
                        msg = msg_list[i]
                        if size(msg) > 0
                            if msg == bytes('000000FFFFFF88FFFFFF')
                                self.screeninit()
                            elif size(msg)>=2 && msg[0]==0x55 && msg[1]==0xBB
                                var jm = string.format("{\"CustomRecv\":\"%s\"}",msg[4..-3].asstring())
                                tasmota.publish_result(jm, "RESULT")        
                            elif msg[0]==0x07 && size(msg)==1 # BELL/Buzzer
                                tasmota.cmd("buzzer 1,1")
                            else
                                var jm = string.format("{\"nextion\":\"%s\"}",str(msg[0..-4]))
                                tasmota.publish_result(jm, "RESULT")        
                            end
                        end       
                    end
                end
            end
        end
    end      

    def begin_nextion_flash()
        self.flash_written = 0
        self.awaiting_offset = 0
        self.flash_offset = 0
        self.sendnx('DRAKJHSUYDGBNCJHGJKSHBDN')
        self.sendnx('recmod=0')
        self.sendnx('recmod=0')
        self.flash_mode = 1
        self.sendnx("connect")        
    end
    
    def open_url_at(url, pos)
		self.url = url
        import string
        var host
        var port
        var s1 = string.split(url,7)[1]
        var i = string.find(s1,":")
        var sa
        if i<0
            port = 80
            i = string.find(s1,"/")
            sa = string.split(s1,i)
            host = sa[0]
        else
            sa = string.split(s1,i)
            host = sa[0]
            s1 = string.split(sa[1],1)[1]
            i = string.find(s1,"/")
            sa = string.split(s1,i)
            port = int(sa[0])
        end
        var get = sa[1]
        log(string.format("FLH: host: %s, port: %s, get: %s",host,port,get))
        self.tcp = tcpclient()
        self.tcp.connect(host,port)
        log("FLH: Connected:"+str(self.tcp.connected()),3)
        var get_req = "GET "+get+" HTTP/1.0\r\n"
		get_req += string.format("Range: bytes=%d-\r\n", pos)
		get_req += string.format("HOST: %s:%s\r\n\r\n",host,port)
        self.tcp.write(get_req)
        var a = self.tcp.available()
        i = 1
        while a==0 && i<5
          tasmota.delay(100*i)
          tasmota.yield() 
          i += 1
          log("FLH: Retry "+str(i),3)
          a = self.tcp.available()
        end
        if a==0
            log("FLH: Nothing available to read!",3)
            return
        end
        var b = self.tcp.readbytes()
        i = 0
        var end_headers = false;
        var headers
        while i<size(b) && headers==nil
            if b[i..(i+3)]==bytes().fromstring("\r\n\r\n") 
                headers = b[0..(i+3)].asstring()
                self.flash_buff = b[(i+4)..]
            else
                i += 1
            end
        end
        #print(headers)
		# check http respose for code 200/206
        if string.find(headers,"200 OK")>0 || string.find(headers,"206 Partial Content")>0
            log("FLH: HTTP Respose is 200 OK or 206 Partial Content",3)
		else
            log("FLH: HTTP Respose is not 200 OK or 206 Partial Content",3)
			print(headers)
			return -1
        end
		# only set flash size if pos is zero
		if pos == 0
			# check http respose for content-length
			var tag = "Content-Length: "
			i = string.find(headers,tag)
			if (i>0) 
				var i2 = string.find(headers,"\r\n",i)
				var s = headers[i+size(tag)..i2-1]
				self.flash_size=int(s)
			end
			log("FLH: Flash file size: "+str(self.flash_size),3)
		end

    end

    def flash_nextion(url)
        self.flash_size = 0
        var res = self.open_url_at(url, 0)
		if res != -1
			self.begin_nextion_flash()
		end
    end

    def init()
        log("NXP: Initializing Driver")
        self.ser = serial(17, 16, 115200, serial.SERIAL_8N1)
        self.flash_mode = 0
    end

end

var nextion = Nextion()

tasmota.add_driver(nextion)

def get_current_version(cmd, idx, payload, payload_json)
	import string
	var version_of_this_script = 4
	var jm = string.format("{\"nlui_driver_version\":\"%s\"}", version_of_this_script)
	tasmota.publish_result(jm, "RESULT")
end

tasmota.add_cmd('GetDriverVersion', get_current_version)

def update_berry_driver(cmd, idx, payload, payload_json)
	def task()
		import string
		var cl = webclient()
		cl.begin(payload)
		var r = cl.GET()
		if r == 200
			print("Sucessfully downloaded nspanel-lovelace-ui berry driver")
		else
			print("Error while downloading nspanel-lovelace-ui berry driver")
		end
		r = cl.write_file("autoexec.be")
		if r < 0
			print("Error while writeing nspanel-lovelace-ui berry driver")
		else
			print("Sucessfully written nspanel-lovelace-ui berry driver")
			var s = load('autoexec.be')
			if s == true
				var jm = string.format("{\"nlui_driver_update\":\"%s\"}", "succeeded")
				tasmota.publish_result(jm, "RESULT")
			else 
				var jm = string.format("{\"nlui_driver_update\":\"%s\"}", "failed")
				tasmota.publish_result(jm, "RESULT")
			end
			
		end
	end
	tasmota.set_timer(0,task)
	tasmota.resp_cmnd_done()
end

tasmota.add_cmd('UpdateDriverVersion', update_berry_driver)

def flash_nextion(cmd, idx, payload, payload_json)
    def task()
        nextion.flash_nextion(payload)
    end
    tasmota.set_timer(0,task)
    tasmota.resp_cmnd_done()
end

def send_cmd(cmd, idx, payload, payload_json)
    nextion.sendnx(payload)
    tasmota.resp_cmnd_done()
end

def send_cmd2(cmd, idx, payload, payload_json)
    nextion.send(payload)
    tasmota.resp_cmnd_done()
end

tasmota.add_cmd('Nextion', send_cmd)
tasmota.add_cmd('CustomSend', send_cmd2)
tasmota.add_cmd('FlashNextion', flash_nextion)

MQTT-Settings:

Sonstige Einstellungen/Vorlage

{"NAME":"NSPanel","GPIO":[0,0,0,0,3872,0,0,0,0,0,32,0,0,0,0,225,0,480,224,1,0,0,0,33,0,0,0,0,0,0,0,0,0,0,4736,0],"FLAG":0,"BASE":1}

Das mqtt.1. muss in beide Richtungen kommunizieren. RESULT funktioniert. Teste es doch bitte so wie beschrieben. Deinen Mosquitto kannst du anschließend immer noch bemühen.

Andreas_Z

@armilar
Habe ich, MQTT.2 ist als Server (mit anderem Port) konfiguriert und identischem Resultat, es wird nichts auf dem Display angezeigt:

mqtt.2	2022-09-23 19:32:17.692	info	Client [NSPanel_1] publishOnSubscribe send all known states
mqtt.2	2022-09-23 19:32:17.691	info	Client [NSPanel_1] publishOnSubscribe send all known states
mqtt.2	2022-09-23 19:32:17.689	info	Client [NSPanel_1] publishOnSubscribe send all known states
mqtt.2	2022-09-23 19:32:17.492	info	Client [NSPanel_1] subscribes on "cmnd/NSPanel_1_fb/#" with regex /^mqtt\.2\.cmnd\.NSPanel_1_fb(\..*)?/
mqtt.2	2022-09-23 19:32:17.492	info	Client [NSPanel_1] subscribes on "cmnd/NSPanel_1_fb/#" with regex /^cmnd\.NSPanel_1_fb(\..*)?/
mqtt.2	2022-09-23 19:32:17.491	info	Client [NSPanel_1] subscribes on "SmartHome/tasmotas/cmnd/#" with regex /^mqtt\.2\.SmartHome\.tasmotas\.cmnd(\..*)?/
mqtt.2	2022-09-23 19:32:17.490	info	Client [NSPanel_1] subscribes on "SmartHome/tasmotas/cmnd/#" with regex /^SmartHome\.tasmotas\.cmnd(\..*)?/
mqtt.2	2022-09-23 19:32:17.489	info	Client [NSPanel_1] subscribes on "SmartHome/NSPanel_1/cmnd/#" with regex /^mqtt\.2\.SmartHome\.NSPanel_1\.cmnd(\..*)?/
mqtt.2	2022-09-23 19:32:17.489	info	Client [NSPanel_1] subscribes on "SmartHome/NSPanel_1/cmnd/#" with regex /^SmartHome\.NSPanel_1\.cmnd(\..*)?/
mqtt.2	2022-09-23 19:32:17.454	info	Client [NSPanel_1] connected with secret 1663954337450_1441
mqtt.2	2022-09-23 19:32:07.977	info	Client [NSPanel_1] connection closed: closed
javascript.0	2022-09-23 19:30:27.658	info	script.js.common.NSPanel_1: registered 12 subscriptions, 6 schedules, 0 messages, 0 logs and 0 file subscriptions
javascript.0	2022-09-23 19:30:27.636	info	script.js.common.NSPanel_1: TypeScript compilation successful
javascript.0	2022-09-23 19:30:25.964	info	script.js.common.NSPanel_1: compiling TypeScript source...
javascript.0	2022-09-23 19:30:25.924	debug	File /home/Javascript/common/NSPanel_1.ts change
javascript.0	2022-09-23 19:30:25.924	info	Stop script script.js.common.NSPanel_1
javascript.0	2022-09-23 19:30:25.917	debug	Update /home/Javascript/common/NSPanel_1.ts on disk

Werte im Script habe ich auf MQTT.2 geändert gehabt.

NEWS

SONOFF NSPanel mit Lovelace UI

Support us

778
Online

30.5k
Users

76.7k
Topics

1.2m
Posts

NEWS

SONOFF NSPanel mit Lovelace UI

Support us

778Online

30.5kUsers

76.7kTopics

1.2mPosts

778
Online

30.5k
Users

76.7k
Topics

1.2m
Posts