For hours trying to figure what is going wrong here. Uninstalled and reinstalled VIS with all depencencies but the problem continues to exist:
All works ok until I want to add a new widget that is nr w00300 or higher. Then connection gets lost and those widgets are not saved anymore. If I delete a few, than adding/modifying is no problem at all. What can be the cause of this?

I'm using stable releases and all adapters are updated to the latest versions. And further:
js controller: 4.0.23
NPM: 8.15
node.js: v16.17.0
Raspberry pi 4, 8GB RAM , 32GB SD

Hope someone can help me with this because I'm totally stuck at the moment

Thanks,
Alex

Hi all,
I just started to integrate some Shelly devices starting with a Shelly plug. After installing an instance of the Shelly adapter and configuring suername and COAP settings (also on Shelly devices) the two Shelly plugs I had installed and connected to my LAN were easily found. Also switching on/off through IOBroker & scripting does work very fine. Also latest firmware is installed.

The problem I have is that the data is not showing in IOBroker objects, they all stay in their default values. No power consumption info, also 'switch' is false even if the plug is on. But for instance the object "led_wifi_disable" does show the correct value.

Already did a delete/install of the instance and factory reset of the Shelly plugs but same results. See also the pictures.

Any idea what can be wrong?

@blauholsten
Perfect, thanks again for all your help and patience!

@blauholsten ,

Well, in that case (setting sharp mode) I get off course a nice burglar alarm when either of the sensors is triggered.

Probably I misunderstand the function of "sharp inside". but let's turnaround the question, with setting the system in "sharp inside" mode, can a burglar alarm be triggered and if so, how should the sensor than be configured. Because the way I've configured it now I only get the "changes warning" with no alarm triggers.

Hi @blauholsten,

You English is much better than my German :).

The last test in my previous example was triggering the outside sensor for which I would expect that the burglar alarm is triggered. However it doesn't....
As next try I removed the Notification checkbox for both sensors. When "Scharf innen" is set, it won't give a log entry anymore when the inside sensor is triggered (as expected) but still the same warnung message "Alarmanlage meldet eine Warnung, Veränderung bei: Outside sensor test" when the outside sensor is triggered instead of a burglar alarm.
The Burglar alarm object is also not set.
So it doesn't work as you describe in your feedback, what should I change in my configuration?

hi @blauholsten,

Thanks again for the module, seems like a lot of work to develop.
I've installed a second instance of the alarm to get the default values again so I can show what I mean. I kept all defaults and only added two sensors, 1 inside, other outside. When I active te alarm and trigger the outside or inside sensor, the alarm goes off as it should.
When I set "Scharf innen" and trigger the inside sensor than I get the warning message that something hs changed, as I have the notifications checked.
When I set "Scherf innen" and trigger the outside sensor I get the same warnung message as with the inside sensor, while I would expect that the burglar alarm would be triggered. Also no alarm flags in the <instance>.status. objects.

What am I missing here?

Thanks for any help/explanation
Alex

Hi all,

For me the first use of the Alarm adapter and there are a few things that don't understand yet, might be caused by the fact that German reading is not that good.
If I understand "Scharf inside" should be used for the condition you want to enable the alarmsystem while there are still people in the house. So I would assume that only sensors outside or for doors/windows are added to this alarmtype and not the internal moving sensors or internal doorsensors. Correct?
"My two qustions are:

1. In below example I've got two internal sensors not checked for the "sharp inside" but they still create an alarm as you can see in the logfile (binnen alarm = sharp inside).
2. Why does the default text/voice only mentions a warning of a change? I would assume that if an outside sensor is triggered it would warn for a burglary.

I guess there i a simple explanation but I can't figure it out yet
Thanks for any help

@homoran Thanks!! I initially uploaded them through SSH but this works much better

@htrecksler I feel so stupid right now, thanks for the tip as it solved my issue.
Do you perhaps also know how I can add my own icons to IOBroker? I've uploaded my own folder with png's but then it doesn't even show the files. I can't however figure out how to do this. Probably also some button I overlooked

Hi all,
I have the problem that when I want to select a custom icon in a widget (with the file manager) I can see the filenames of the icons, but not the icon image itself, see the picture below.
This is only in the folders of custom installed icon adapters like mfd-icons-png. When a scroll to /vis/icon then I can see also the images itself.
How can I fix this?
Thanks for any help