Einstellungen von Shuttercontrol
-
@stealthangel Laut dem Log hat Shuttercontrol mit dem Überprüfen nach 60 Sekunden alles richtig gemacht.
Automatik wurde erkannt und er wurde in den Sonnenschutz gefahren.Ich gehe mal davon aus, dass da bei deinen States der Rollläden was krum ist.
Hast du da noch irgendwelche Scripte laufen?Wann wurde denn der State des Rollladens geändert?
-
@stealthangel Warum nutzt du nicht den Shelly Adapter??? Würde sicher einiges erleichtern
-
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel Warum nutzt du nicht den Shelly Adapter??? Würde sicher einiges erleichtern
Ich habe jetzt auch auf den Shelly Adapter umgestellt. Das Problem ist aber immer noch das Gleiche
Der Rollladen ist wieder 3 mal runter und rauf gefahren. So langsam verzweifele ich ....
2023-04-17 14:45:00.014 - debug: shuttercontrol.0 (207218) calculate astrodata ... 2023-04-17 14:45:00.014 - debug: shuttercontrol.0 (207218) Sun Azimut: 209° 2023-04-17 14:45:00.015 - debug: shuttercontrol.0 (207218) Sun Elevation: 45.3° 2023-04-17 14:46:12.976 - debug: shuttercontrol.0 (207218) Brightness sensor value: 5032 2023-04-17 14:46:14.052 - debug: shuttercontrol.0 (207218) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-17 14:46:22.978 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:48:53.703 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4799 2023-04-17 14:48:54.799 - debug: shuttercontrol.0 (207218) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-17 14:49:03.703 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:50:00.019 - debug: shuttercontrol.0 (207218) calculate astrodata ... 2023-04-17 14:50:00.020 - debug: shuttercontrol.0 (207218) Sun Azimut: 210.7° 2023-04-17 14:50:00.021 - debug: shuttercontrol.0 (207218) Sun Elevation: 44.9° 2023-04-17 14:50:02.035 - debug: shuttercontrol.0 (207218) BueroRollladen: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-17 14:50:02.036 - info: shuttercontrol.0 (207218) Sunprotect #416 Set ID: BueroRollladen value: 30% 2023-04-17 14:50:02.048 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:50:02.059 - debug: shuttercontrol.0 (207218) Sunprotect for BueroRollladen is active 2023-04-17 14:50:02.060 - debug: shuttercontrol.0 (207218) RangeMinus: 210 < 210.7RangePlus: 320 > 210.7 2023-04-17 14:50:02.060 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: down_Sunprotect 2023-04-17 14:50:02.060 - debug: shuttercontrol.0 (207218) Sunprotect BueroRollladen old height: % new height: 30% 2023-04-17 14:50:02.083 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:50:14.335 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:51:02.049 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:51:02.051 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 30 2023-04-17 14:51:02.051 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:51:02.052 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:51:02.052 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:51:02.052 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:51:02.053 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:51:02.053 - debug: shuttercontrol.0 (207218) #1 oldHeight: % 2023-04-17 14:51:02.053 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:51:02.053 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:51:02.084 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:51:02.085 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 30 2023-04-17 14:51:02.086 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:51:02.087 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:51:02.087 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:51:02.087 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:51:02.088 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:51:02.088 - debug: shuttercontrol.0 (207218) #1 oldHeight: % 2023-04-17 14:51:02.089 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:51:02.089 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:51:02.091 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = . New value = 30 2023-04-17 14:51:02.092 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:51:02.142 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = . New value = 30 2023-04-17 14:51:02.143 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:51:14.336 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:51:14.338 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 30 2023-04-17 14:51:14.338 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:51:14.339 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:51:14.339 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:51:14.339 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:51:14.339 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:51:14.340 - debug: shuttercontrol.0 (207218) #1 oldHeight: % 2023-04-17 14:51:14.340 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:51:14.340 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:51:14.390 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = . New value = 30 2023-04-17 14:51:14.391 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:51:19.961 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4622 2023-04-17 14:51:19.995 - info: shuttercontrol.0 (207218) Lightsensor #5 Set ID: BueroRollladen value: 100% 2023-04-17 14:51:20.003 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:51:20.013 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: up_Brightness 2023-04-17 14:51:20.013 - debug: shuttercontrol.0 (207218) save current height: 100% from BueroRollladen 2023-04-17 14:51:20.035 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:51:29.963 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:51:33.042 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:52:20.004 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:52:20.005 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 100 2023-04-17 14:52:20.006 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = . New value = 100. automatic is active 2023-04-17 14:52:20.035 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:52:20.037 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 100 2023-04-17 14:52:20.038 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = . New value = 100. automatic is active 2023-04-17 14:52:33.043 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:52:33.044 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 100 2023-04-17 14:52:33.045 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = . New value = 100. automatic is active 2023-04-17 14:53:31.713 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4502 2023-04-17 14:53:31.770 - debug: shuttercontrol.0 (207218) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-17 14:53:41.714 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:55:00.017 - debug: shuttercontrol.0 (207218) calculate astrodata ... 2023-04-17 14:55:00.018 - debug: shuttercontrol.0 (207218) Sun Azimut: 212.3° 2023-04-17 14:55:00.018 - debug: shuttercontrol.0 (207218) Sun Elevation: 44.5° 2023-04-17 14:55:02.040 - debug: shuttercontrol.0 (207218) BueroRollladen: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-17 14:55:02.041 - info: shuttercontrol.0 (207218) Sunprotect #416 Set ID: BueroRollladen value: 30% 2023-04-17 14:55:02.093 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:55:02.111 - debug: shuttercontrol.0 (207218) Sunprotect for BueroRollladen is active 2023-04-17 14:55:02.112 - debug: shuttercontrol.0 (207218) RangeMinus: 210 < 212.3RangePlus: 320 > 212.3 2023-04-17 14:55:02.113 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: down_Sunprotect 2023-04-17 14:55:02.113 - debug: shuttercontrol.0 (207218) Sunprotect BueroRollladen old height: 100% new height: 30% 2023-04-17 14:55:02.136 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:55:14.373 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:56:02.095 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:56:02.097 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 14:56:02.098 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:56:02.099 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:56:02.099 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:56:02.100 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:56:02.100 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:56:02.101 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 14:56:02.101 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:56:02.101 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:56:02.137 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:56:02.143 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 14:56:02.144 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:56:02.144 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:56:02.145 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:56:02.146 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:56:02.146 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:56:02.147 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 14:56:02.147 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:56:02.148 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:56:02.152 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 14:56:02.153 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:56:02.208 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 14:56:02.209 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:56:14.374 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:56:14.377 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 14:56:14.377 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:56:14.378 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:56:14.378 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:56:14.378 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:56:14.378 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:56:14.379 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 14:56:14.379 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:56:14.379 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:56:14.432 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 14:56:14.432 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:56:32.952 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4650 2023-04-17 14:56:32.992 - info: shuttercontrol.0 (207218) Lightsensor #5 Set ID: BueroRollladen value: 100% 2023-04-17 14:56:33.000 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:56:33.010 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: up_Brightness 2023-04-17 14:56:33.011 - debug: shuttercontrol.0 (207218) save current height: 100% from BueroRollladen 2023-04-17 14:56:33.032 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:56:42.953 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:56:46.052 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:57:26.778 - info: admin.0 (831) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-17 14:57:33.002 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:57:33.003 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = 100. New value = 100. automatic is active 2023-04-17 14:57:33.032 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:57:33.034 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = 100. New value = 100. automatic is active 2023-04-17 14:57:38.475 - info: admin.0 (831) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-17 14:57:46.054 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:57:46.055 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = 100. New value = 100. automatic is active 2023-04-17 14:59:19.969 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4804 2023-04-17 14:59:20.020 - debug: shuttercontrol.0 (207218) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-17 14:59:29.971 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 15:00:00.012 - debug: shuttercontrol.0 (207218) calculate astrodata ... 2023-04-17 15:00:00.013 - debug: shuttercontrol.0 (207218) Sun Azimut: 213.9° 2023-04-17 15:00:00.013 - debug: shuttercontrol.0 (207218) Sun Elevation: 44.1° 2023-04-17 15:00:02.026 - debug: shuttercontrol.0 (207218) BueroRollladen: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-17 15:00:02.026 - info: shuttercontrol.0 (207218) Sunprotect #416 Set ID: BueroRollladen value: 30% 2023-04-17 15:00:02.075 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:00:02.086 - debug: shuttercontrol.0 (207218) Sunprotect for BueroRollladen is active 2023-04-17 15:00:02.086 - debug: shuttercontrol.0 (207218) RangeMinus: 210 < 213.9RangePlus: 320 > 213.9 2023-04-17 15:00:02.086 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: down_Sunprotect 2023-04-17 15:00:02.087 - debug: shuttercontrol.0 (207218) Sunprotect BueroRollladen old height: 100% new height: 30% 2023-04-17 15:00:02.105 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:00:14.359 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:01:02.077 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 15:01:02.078 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 15:01:02.079 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 15:01:02.079 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 15:01:02.080 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 15:01:02.080 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 15:01:02.080 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 15:01:02.080 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 15:01:02.081 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 15:01:02.081 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 15:01:02.106 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 15:01:02.128 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 15:01:02.128 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 15:01:02.129 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 15:01:02.130 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 15:01:02.130 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 15:01:02.132 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 15:01:02.132 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 15:01:02.132 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 15:01:02.133 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 15:01:02.140 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 15:01:02.140 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 15:01:02.188 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 15:01:02.188 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 15:01:14.360 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 15:01:14.361 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 15:01:14.362 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 15:01:14.362 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 15:01:14.362 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 15:01:14.363 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 15:01:14.363 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 15:01:14.363 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 15:01:14.363 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 15:01:14.364 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 15:01:14.415 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 15:01:14.415 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 15:01:52.457 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4873 2023-04-17 15:01:52.494 - info: shuttercontrol.0 (207218) Lightsensor #5 Set ID: BueroRollladen value: 100% 2023-04-17 15:01:52.506 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:01:52.520 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: up_Brightness 2023-04-17 15:01:52.520 - debug: shuttercontrol.0 (207218) save current height: 100% from BueroRollladen 2023-04-17 15:01:52.537 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:02:02.459 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 15:02:05.565 - debug: shuttercontrol.0 (207218) #0 wait for shutter check startedAlso irgendwas läuft noch falsch.
Mich wundert, dass sich der Status ändert. Ist das so richtig?Screenshot ist von einem etwas späteren Zeitpunkt, war aber sonst auch so, allerdings nicht geloggt....
Jetzt wo ich hier schreibe, fährt der Rollladen munter weiter rauf und runter.
Es ist mit dem Shelly-Adapter also massiv schlechter geworden -
@stealthangel Bitte teste die aktuelle v1.4.28
-
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel Bitte teste die aktuelle v1.4.28
Funktioniert auch nicht richtig
Das einzige was sich jetzt geändert hat ist, dass der Rollladen nicht mehr komplett rauf und runter fährt, sondern nur ca. 5% und das jetzt fast im Sekunden Takt.
Am besten sieht man das an der Shelly Shutter.Position Objekt:
Hier auch noch das Debug:
2023-04-18 15:34:50.700 - debug: shuttercontrol.0 (208390) Brightness sensor value: 8371 2023-04-18 15:34:50.742 - debug: shuttercontrol.0 (208390) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-18 15:35:00.016 - debug: shuttercontrol.0 (208390) calculate astrodata ... 2023-04-18 15:35:00.017 - debug: shuttercontrol.0 (208390) Sun Azimut: 224.9° 2023-04-18 15:35:00.018 - debug: shuttercontrol.0 (208390) Sun Elevation: 41° 2023-04-18 15:35:00.700 - debug: shuttercontrol.0 (208390) Brightness State Down is: false 2023-04-18 15:35:02.073 - debug: shuttercontrol.0 (208390) BueroRollladen: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-18 15:35:02.074 - info: shuttercontrol.0 (208390) Sunprotect #416 Set ID: BueroRollladen value: 30% 2023-04-18 15:35:02.122 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:35:02.141 - debug: shuttercontrol.0 (208390) Sunprotect for BueroRollladen is active 2023-04-18 15:35:02.142 - debug: shuttercontrol.0 (208390) RangeMinus: 210 < 224.9RangePlus: 320 > 224.9 2023-04-18 15:35:02.144 - debug: shuttercontrol.0 (208390) last automatic Action for BueroRollladen: down_Sunprotect 2023-04-18 15:35:02.144 - debug: shuttercontrol.0 (208390) Sunprotect BueroRollladen old height: 100% new height: 30% 2023-04-18 15:35:02.166 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:35:03.157 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:35:05.773 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:36:02.124 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:36:02.167 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:36:03.158 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:36:05.775 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:37:08.708 - debug: shuttercontrol.0 (208390) Brightness sensor value: 8611 2023-04-18 15:37:08.784 - info: shuttercontrol.0 (208390) Lightsensor #5 Set ID: BueroRollladen value: 30% 2023-04-18 15:37:08.793 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:37:08.806 - debug: shuttercontrol.0 (208390) last automatic Action for BueroRollladen: up_Brightness 2023-04-18 15:37:08.807 - debug: shuttercontrol.0 (208390) save current height: 30% from BueroRollladen 2023-04-18 15:37:08.824 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:37:09.861 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:37:10.839 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:37:11.852 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:37:12.863 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:37:13.883 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:37:16.495 - debug: shuttercontrol.0 (208390) #0 wait for shutter check started 2023-04-18 15:37:18.709 - debug: shuttercontrol.0 (208390) Brightness State Down is: false 2023-04-18 15:38:08.794 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:38:08.825 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:38:09.860 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:38:10.840 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:38:11.853 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:38:12.863 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:38:13.884 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:38:16.496 - debug: shuttercontrol.0 (208390) #0 wait for shutter check end 2023-04-18 15:39:12.143 - debug: shuttercontrol.0 (208390) Brightness sensor value: 8592 2023-04-18 15:39:22.144 - debug: shuttercontrol.0 (208390) Brightness State Down is: false 2023-04-18 15:40:00.010 - debug: shuttercontrol.0 (208390) calculate astrodata ... 2023-04-18 15:40:00.010 - debug: shuttercontrol.0 (208390) Sun Azimut: 226.4° 2023-04-18 15:40:00.011 - debug: shuttercontrol.0 (208390) Sun Elevation: 40.4° 2023-04-18 15:42:05.421 - debug: shuttercontrol.0 (208390) Brightness sensor value: 8634 2023-04-18 15:42:15.421 - debug: shuttercontrol.0 (208390) Brightness State Down is: false 2023-04-18 15:44:44.194 - debug: shuttercontrol.0 (208390) Brightness sensor value: 8423 2023-04-18 15:44:54.195 - debug: shuttercontrol.0 (208390) Brightness State Down is: false 2023-04-18 15:45:00.011 - debug: shuttercontrol.0 (208390) calculate astrodata ... 2023-04-18 15:45:00.011 - debug: shuttercontrol.0 (208390) Sun Azimut: 227.8° 2023-04-18 15:45:00.012 - debug: shuttercontrol.0 (208390) Sun Elevation: 39.8°Auch die Position in den Objekten passt nicht.
shutters.autoLevel.BueroRollladen steht auf 30%
Shelly.Shutter.Position sagt aber 100% (und das ist auch richtig) -
@simatec Wenn Du mir mit einigen Worten erklärst wie das Ganze funktionieren soll, würde ich mich bereit erklären und etwas in den Source-Code abzutauchen und Debug-Hilfe zugeben....
-
@stealthangel sagte in Einstellungen von Shuttercontrol:
Am besten sieht man das an der Shelly Shutter.Position Objekt:
das sieht für mich aus als ob der Shelly die Position unsauber durchgibt (flattert)
im Millisekundenbereich von 92 auf 98 u.ä. -
@stealthangel Poste mal deine Config hier als JSON.
Da ist bei dir völlig was krumm… Shuttercontrol gibt nur einen Fahrbefehl an deinen Rollladen.
Schalte alle Scripte und sonstige Routinen ab -
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel Poste mal deine Config hier als JSON.
Hier ist die Config: system.adapter.shuttercontrol.0 (2).json
Da ist bei dir völlig was krumm… Shuttercontrol gibt nur einen Fahrbefehl an deinen Rollladen.
Schalte alle Scripte und sonstige Routinen abEs gibt keine anderen Skripte oder Routinen
Das Flattern habe ich auch nur mit dem Shelly-Adapter gesehen. Als ich das noch über MQTT gemacht habe war der Positionswert sauber, aber der Shuttercontrol hat trotzdem nicht richtig funktioniert...
-
Noch zwei Fragen:
1.) Wenn ich in den Objekten "autoSun" auf "false" stelle während der Sonnenschutz aktiv ist, müsste dann sunProtect nicht beendet werden und die Rollläden wieder hoch fahren?
2.) Wenn der Rollladen bei "autoDown" runter fährt und das Fenster offen ist würde ich erwarten das der Rollladen nur bis auf den Wert runter fährt der bei "Rollladenhöhe bei öffnen des Fensters oder Tür" definiert ist. Bei mir fährt der Rollladen jedoch komplett runter und erst wenn ich das Fenster zu und wieder auf mache, wird die "richtige" Rollladenhöhe gefahren.
Oder verstehe ich da irgendwas falsch?
-
- Nein ist nicht so angedacht ...
- Aussperrschutz falsch konfiguriert
