M-TEC Energy Butler

manrum1

@metaxa Hallo, ich bin noch am Abwarten, dass meine Anlage vom EVU abgenommen wird. Bis dahin möchte ich nichts an der Anlage verändern. Aber sicher werde ich danach die Anlage anbinden.

Warne ausdrücklich von der genannten Installationsfirma aus München!!!! (FX-RIDER weiß wovon ich spreche)...

Homoran

@metaxa sagte in M-TEC Energy Butler:

wurde das CAT7 Kabel an der richtigen Stelle des BUS Systems dazugehängt,

modbus RTU braucht ein twisted pair davon.

hast du den Waveshare?

@homoran sagte in M-TEC Energy Butler:

erst mal nur einen bei Input

muss mich korrigieren 40000er sind Holding. unüblich, kommt aber vor

was hast du gen2 nimmt holding, gen3 anscheinend Inputregister (30000er)

metaxa

@homoran sagte in M-TEC Energy Butler:

modbus RTU braucht ein twisted pair davon.

Der Elektriker hat wie bei der Busverkabelung zwischen den beiden Geräten jeweils ein Pärchen zusammen für A und ein anderes für B sowie für GND genommen.

@homoran sagte in M-TEC Energy Butler:

gen3 anscheinend Inputregister (30000er)

Habe Gen3 und so eingetragen

Ahhhh! Jetzt wird der Adapter schon gesprächiger :-)


modbus.0
2023-06-23 21:30:59.005	error	unknown function code: 0x1d, 0x0

modbus.0
2023-06-23 21:30:58.993	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:30:58.978	error	Wrong CRC for frame: 247,3,42,254,0,60,56,165,247,3,120,16,25,16,19,16,24,9,73,0,9,9,72,0,37,9,74,0,10,19,134,0,0,3,103,0,0,1,34,0,0,1,127,0,0,0,30

modbus.0
2023-06-23 21:30:58.868	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:30:58.849	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:30:58.827	error	Wrong CRC for frame: 247,3,128,232,0,18,120,165,247,3,36,21,198,39,15,0,2,0,249,255,255,255,255,255,255,255,255,0,0,1,7,0,0,0,236,0,0,12,196,0,0,12,185,0,0,0,0,116,195,247,3,42,242,0,8,249,113,247,3,16,0,0,0,0,0,0,0,4,0,0,0,7,0,0,0,15,216,192,247,3,39,16,0,11,27,234,247,3,22,90,49,49,50,51,48,48,50,48,56,51,51,48,50,54,49,30,6,0,0,0,0,190,217,247,3,39,121,0,17,74,61,247,3,34,0,2,0,0,0,0,0,0,0

modbus.0
2023-06-23 21:30:57.506	debug	[DevID_0/inputRegs] Poll address 2999 - 1 registers

modbus.0
2023-06-23 21:30:57.506	debug	[DevID_0] Poll start ---------------------

modbus.0
2023-06-23 21:30:56.451	warn	Poll error count: 2 code: "ReadInputRegisters: Invalid FC 3"

modbus.0
2023-06-23 21:30:56.449	debug	received answer for wrong ID 247, expected 0

modbus.0
2023-06-23 21:30:56.305	error	Error response: 9b

modbus.0
2023-06-23 21:30:56.240	error	unknown function code: 0x8, 0x29

modbus.0
2023-06-23 21:30:56.225	error	unknown function code: 0x0, 0xf

modbus.0
2023-06-23 21:30:56.209	error	unknown function code: 0x4e, 0x20

modbus.0
2023-06-23 21:30:56.193	error	Error response: 1e

modbus.0
2023-06-23 21:30:56.177	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:30:56.161	error	Wrong CRC for frame: 247,3,42,254,0,60,56,165,247,3,120,16,25,16,20,16,24,9,73,0,9,9,73,0,38,9,74,0,10,19,134,0,0,3,117,0,0,1,34,0,0,1,127,0,0,0,30

modbus.0
2023-06-23 21:30:56.049	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:30:56.033	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:30:56.017	error	Wrong CRC for frame: 247,3,128,232,0,18,120,165,247,3,36,21,198,39,15,0,2,0,249,255,255,255,255,255,255,255,255,0,0,1,7,0,0,0,235,0,0,12,196,0,0,12,185,0,0,0,0,127,132,247,3,42,242,0,8,249,113,247,3,16,0,0,0,0,255,255,255,252,0,0,0,9,0,0,0,0,195,48,247,3,39,16,0,11,27,234,247,3,22,90,49,49,50,51,48,48,50,48,56,51,51,48,50,54,49,30,6,0,0,0,0,190,217,247,3,39,121,0,17,74,61,247,3,34,0,2,0,0,0,0,0,0,0

modbus.0
2023-06-23 21:30:54.215	debug	[DevID_0/inputRegs] Poll address 2999 - 1 registers

modbus.0
2023-06-23 21:30:54.213	debug	[DevID_0] Poll start ---------------------

modbus.0
2023-06-23 21:30:53.654	error	Wrong CRC for frame: 247,3,117,248,0,60,202,176,247,3,120,9,67,0,5,19,134,0,0,0,0,0,41,0,0,0,0,0,0,0,0,9,59,0,41,19,134,0,0,0,0,3,69,0,0,0,0,0,0,0,0,9,69,0,3,19,129,0,0,0,0,0,27,0,0,0,0,0,0,0,0,0,0,3,137,0,0,0,0,0,0,0,0,0,0,0,81,0,0,0,0,0,0,0,0,0,0,3,119,0,0,0,0,0,0,0,0,0,0,0,87,0,0,0,0,0,0,0,0,9,32,0

modbus.0
2023-06-23 21:30:53.446	debug	received answer for wrong ID 247, expected 0

modbus.0
2023-06-23 21:30:53.303	error	Error response: Value is not accepted by slave

modbus.0
2023-06-23 21:30:53.302	error	Error response for FCx119: Illegal Data Value

modbus.0
2023-06-23 21:30:53.240	error	Wrong CRC for frame: 247,3,39,121,0,17,74,61,247,3,34,0,2,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

modbus.0
2023-06-23 21:30:53.147	warn	Poll error count: 1 code: "ReadInputRegisters: Invalid FC 3"

modbus.0
2023-06-23 21:30:53.144	debug	received answer for wrong ID 247, expected 0

modbus.0
2023-06-23 21:30:53.105	error	unknown function code: 0x3b, 0xf7

modbus.0
2023-06-23 21:30:51.779	debug	[DevID_0/inputRegs] Poll address 2999 - 1 registers

modbus.0
2023-06-23 21:30:51.742	debug	Initialization of scale factors done!

modbus.0
2023-06-23 21:30:51.739	debug	[DevID_0] Poll start ---------------------

modbus.0
2023-06-23 21:30:51.737	info	Connected to slave

modbus.0
2023-06-23 21:30:51.705	debug	connect to serial /dev/ttyUSB1 with 9600

modbus.0
2023-06-23 21:30:50.406	debug	Initialize Objects for holdingRegs: []

modbus.0
2023-06-23 21:30:50.404	debug	Add inputRegisters.33000_State_of_Charge_(SOC): {"_id":"inputRegisters.33000_State_of_Charge_(SOC)","type":"state","common":{"name":"Ladezustand der Batterie","role":"level","type":"number","read":true,"write":false,"def":0,"unit":"%"},"native":{"regType":"inputRegs","address":2999,"deviceId":0,"type":"uint16be","len":1,"offset":0,"factor":1}}

modbus.0
2023-06-23 21:30:50.403	debug	Initialize Objects for inputRegs: [{"_address":"33000","name":"State of Charge (SOC)","description":"Ladezustand der Batterie","unit":"%","type":"uint16be","len":1,"factor":1,"offset":0,"formula":"","role":"level","room":"","cw":"","isScale":"","address":2999,"deviceId":0,"id":"inputRegisters.33000_State_of_Charge_(SOC)"}]

modbus.0
2023-06-23 21:30:50.401	debug	Initialize Objects for coils: []

modbus.0
2023-06-23 21:30:50.398	debug	Initialize Objects for disInputs: []

modbus.0
2023-06-23 21:30:49.502	info	starting. Version 5.0.11 in /opt/iobroker/node_modules/iobroker.modbus, node: v16.19.1, js-controller: 4.0.24

wo stelle ich den falschen Port im Adapter richtig?

Homoran

@metaxa sagte in M-TEC Energy Butler:

wo stelle ich den falschen Port im Adapter richtig?

Port?
ist das nicht die Geräte ID? die hast du nicht ausgefüllt

metaxa

@manrum1 sagte in M-TEC Energy Butler:

nichts an der Anlage verändern

das tue ich auch nicht, mein Solateur hat mir das BUS Kabel angeschlossen

@manrum1 sagte in M-TEC Energy Butler:

Warne ausdrücklich von der genannten Installationsfirma aus München!!!!

In diese Versuchung kam ich in Wien nicht :-) aber herzlichen Dank für die Info!

metaxa

@homoran sagte in M-TEC Energy Butler:

ist das nicht die Geräte ID?

Mahhhh, richtig
Der Fehler ist jetzt einmal weg, bleiben aber noch genügend andere :cold_sweat:


modbus.0
2023-06-23 21:45:17.734	warn	Poll error count: 1 code: "ReadInputRegisters: Invalid FC 3"

modbus.0
2023-06-23 21:45:17.701	error	unknown function code: 0x0, 0xef

modbus.0
2023-06-23 21:45:17.636	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:45:17.620	error	Wrong CRC for frame: 0,3,20,144,90,247,3,128,232,0,18,120,165,247,3,36,21,8,39,15,0,2,0,248,255

modbus.0
2023-06-23 21:45:17.527	error	Wrong CRC for frame: 247,3,117,248,0,60,202,176,247,3,120,9,74,0,5,19,136,0,0,0,0,0,41,0,0,0,0,0,0,0,0,9,64,0,37,19,134,0,0,0,0,2,225,0,0,0,0,0,0,0,0,9,82,0,3,19,139,0,0,0,0,0,27,0,0,0,0,0,0,0,0,0,0,3,37,0,0,0,0,0,0,0,0,0,0,0,82,0,0,0,0,0,0,0,0,0,0,3,7,0,0,0,0,0,0,0,0,0,0,0,85,0,0,0,0,0,0,0,0,9,29,0

modbus.0
2023-06-23 21:45:17.341	error	Wrong CRC for frame: 1,1,0,0,0

modbus.0
2023-06-23 21:45:17.320	error	unknown function code: 0x0, 0x40

modbus.0
2023-06-23 21:45:17.317	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:45:17.285	error	unknown function code: 0x26, 0x0

modbus.0
2023-06-23 21:45:17.269	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:45:17.253	error	Wrong CRC for frame: 247,3,42,254,0,60,56,165,247,3,120,16,41,16,34,16,35,9,78,0,9,9,83,0,34,9,83,0,10,19,134,0,0,3,25,0,0,1,36,0,0,1,129,0,0,0,31

modbus.0
2023-06-23 21:45:17.148	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:45:17.125	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 21:45:17.116	error	unknown function code: 0x22, 0x0

modbus.0
2023-06-23 21:45:17.095	error	Wrong CRC for frame: 247,3,39,16,0,11,27,234,247,3,22,90,49,49,50,51,48,48,50,48,56,51,51,48,50,54,49,30,6,0,0,0,0,190,217,247,3,39,121,0,17,74,61,247

modbus.0
2023-06-23 21:45:16.064	debug	[DevID_247/inputRegs] Poll address 2999 - 1 registers

modbus.0
2023-06-23 21:45:16.055	debug	Initialization of scale factors done!

modbus.0
2023-06-23 21:45:16.042	debug	[DevID_247] Poll start ---------------------

modbus.0
2023-06-23 21:45:16.041	info	Connected to slave

Homoran

@metaxa wrong crc hab ich noch nie gehabt
A/B richtig rum?

metaxa

@homoran sagte in M-TEC Energy Butler:

A/B richtig rum?

Wie gesagt, mein Elektriker hat das gemacht. Aber ich springe mal in den Keller und tausche A/B um.

@homoran sagte in M-TEC Energy Butler:

hast du den Waveshare?

Ja, den von dir empfohlenen (habe ihn auf 5V geschalten seitlich).

Homoran

@metaxa sagte in M-TEC Energy Butler:

, den von dir empfohlenen

da hatcder Elektriker auch angeklemmt?

metaxa

@homoran sagte in M-TEC Energy Butler:

da hatcder Elektriker auch angeklemmt?

Ja, aber nur am Stecker

Könnte diese Einstellung auch falsch sein?

Ich gehe jetzt einmal umklemmen :-)

Homoran

@metaxa sagte in M-TEC Energy Butler:

Könnte diese Einstellung auch falsch sein?

ja, aber die hätte ich auch genommen.

Ab jetzt fische ich auch im trüben und würde in den allgemeinen Parametern spielen.

Alias mal aus -> was dann?
und auch die anderen Checkboxen mal testen

metaxa

@metaxa sagte in M-TEC Energy Butler:

Ich gehe jetzt einmal umklemmen

Uiiiiiii ..... das sind mehr Fehler als vorher


modbus.0
2023-06-23 21:59:39.687	info	Disconnected from slave

modbus.0
2023-06-23 21:59:39.583	error	Wrong CRC for frame: 255,1,2,2,52,252,255

modbus.0
2023-06-23 21:59:39.567	error	unknown function code: 0x0, 0x4

modbus.0
2023-06-23 21:59:39.552	error	unknown function code: 0x7e, 0xb5

modbus.0
2023-06-23 21:59:39.500	error	Error response: ff

modbus.0
2023-06-23 21:59:39.491	error	Error response: fd

modbus.0
2023-06-23 21:59:39.470	error	unknown function code: 0x7e, 0xdb

modbus.0
2023-06-23 21:59:39.441	error	unknown function code: 0x7e, 0x5e

modbus.0
2023-06-23 21:59:39.393	error	Error response: e2

modbus.0
2023-06-23 21:59:39.381	error	Error response: ff

modbus.0
2023-06-23 21:59:39.366	error	Error response: ff

modbus.0
2023-06-23 21:59:39.348	error	Error response: ff

modbus.0
2023-06-23 21:59:39.336	error	Error response: f9

modbus.0
2023-06-23 21:59:39.318	error	Error response: ff

modbus.0
2023-06-23 21:59:39.302	error	unknown function code: 0x65, 0xff

modbus.0
2023-06-23 21:59:39.297	error	Error response: ff

modbus.0
2023-06-23 21:59:39.282	error	Error response: af

modbus.0
2023-06-23 21:59:39.277	error	Error response: fe

modbus.0
2023-06-23 21:59:39.259	error	unknown function code: 0x0, 0x4

modbus.0
2023-06-23 21:59:39.242	error	unknown function code: 0x0, 0x4

modbus.0
2023-06-23 21:59:39.182	error	Error response: ff

modbus.0
2023-06-23 21:59:39.174	error	Error response: a9

modbus.0
2023-06-23 21:59:39.158	error	Error response: ff

modbus.0
2023-06-23 21:59:39.144	error	Error response: ff

modbus.0
2023-06-23 21:59:39.129	error	Error response: fd

modbus.0
2023-06-23 21:59:39.110	error	Error response: ff

modbus.0
2023-06-23 21:59:39.093	error	Error response: eb

modbus.0
2023-06-23 21:59:39.075	error	Wrong CRC for frame: 0,4,126,181,131,239,13,58,0,4,126,247,255,255,255,1,2,2,140,252,255,255,241,255,255,255,255,3,93,0,4,126,108,247,233,201,43,0,4,126,186,169,103,103,179,102,246,182,246,246,44,150,246,182,54,214,54,110,255,255,255,255,131,154,0,4,126,108,67,221,107,133,0,4,126,183,251,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,81,94,0,4,126,181,128,135,143,181,0,4,126,232,183,251,151,247,151,107,97,255

modbus.0
2023-06-23 21:59:38.686	warn	Poll error count: 1 code: {"err":"timeout","timeout":5000}

modbus.0
2023-06-23 21:59:38.685	error	Request timed out.

modbus.0
2023-06-23 21:59:38.684	warn	Error: undefined

modbus.0
2023-06-23 21:59:36.679	error	Error response: e7

modbus.0
2023-06-23 21:59:36.664	error	Error response: fb

modbus.0
2023-06-23 21:59:36.657	error	Error response: fb

modbus.0
2023-06-23 21:59:36.641	error	unknown function code: 0x7e, 0xdb

modbus.0
2023-06-23 21:59:36.626	error	unknown function code: 0x7e, 0x5e

modbus.0
2023-06-23 21:59:36.570	error	Error response: 52

modbus.0
2023-06-23 21:59:36.564	error	Error response: ff

modbus.0
2023-06-23 21:59:36.548	error	Error response: ff

modbus.0
2023-06-23 21:59:36.532	error	Error response: ff

modbus.0
2023-06-23 21:59:36.523	error	Error response: f9

modbus.0
2023-06-23 21:59:36.504	error	Error response: ff

modbus.0
2023-06-23 21:59:36.489	error	unknown function code: 0x65, 0xff

modbus.0
2023-06-23 21:59:36.483	error	Error response: ff

modbus.0
2023-06-23 21:59:36.467	error	unknown function code: 0x79, 0xff

modbus.0
2023-06-23 21:59:36.462	error	Error response: f3

modbus.0
2023-06-23 21:59:36.444	error	unknown function code: 0x0, 0x4

modbus.0
2023-06-23 21:59:36.428	error	Wrong CRC for frame: 0,4,126,232,247,251,183,247,151,107,103,255,237,237,103,255,183,237,91,255,235,217,243,254,255,249,241,254,255,253,179,255,255,253,249,254,255,255,193,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,253,157,250,129,250,187,250,129,134,115,225,185,255,255,255,253,255,255,255,253,99,191,101,49,198,129,255,255,173,137,254,255,255,251,91,117,225,1,254,225,253,253,255,127,195,169,134,169,174,111,159,143,235,239,173,247,253,253,255,255,255,255,255,255,255,255,255,255,37,154,0,4,126,69,224,135

modbus.0
2023-06-23 21:59:36.230	error	Wrong CRC for frame: 0,4,126,108,247,233,201,43,0,4,126,186,169,103,103,179,102,246,182,246,246,44,150,246,182,54,214,54,110,255,255,255,255,131,154,0,4,126,108,67,221,107,133,0,4,126,183,251,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,81,94,0,4,126,108,67,221,107,133,0,4,126,183,251,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,81,94,0,4

modbus.0
2023-06-23 21:59:33.671	debug	[DevID_247/inputRegs] Poll address 2999 - 1 registers

modbus.0
2023-06-23 21:59:33.670	debug	Initialization of scale factors done!

modbus.0
2023-06-23 21:59:33.667	debug	[DevID_247] Poll start ---------------------

modbus.0
2023-06-23 21:59:33.665	info	Connected to slave

modbus.0
2023-06-23 21:59:33.636	debug	connect to serial /dev/ttyUSB1 with 9600

modbus.0
2023-06-23 21:59:32.476	debug	Initialize Objects for holdingRegs: []

modbus.0
2023-06-23 21:59:32.473	debug	Add inputRegisters.33000_State_of_Charge_(SOC): {"_id":"inputRegisters.33000_State_of_Charge_(SOC)","type":"state","common":{"name":"Ladezustand der Batterie","role":"level","type":"number","read":true,"write":false,"def":0,"unit":"%"},"native":{"regType":"inputRegs","address":2999,"deviceId":247,"type":"uint16be","len":1,"offset":0,"factor":1}}

modbus.0
2023-06-23 21:59:32.469	debug	Initialize Objects for inputRegs: [{"_address":"33000","name":"State of Charge (SOC)","description":"Ladezustand der Batterie","unit":"%","type":"uint16be","len":1,"factor":1,"offset":0,"formula":"","role":"level","room":"","cw":"","isScale":"","address":2999,"deviceId":247,"id":"inputRegisters.33000_State_of_Charge_(SOC)"}]

modbus.0
2023-06-23 21:59:32.461	debug	Initialize Objects for coils: []

modbus.0
2023-06-23 21:59:32.458	debug	Initialize Objects for disInputs: []

modbus.0
2023-06-23 21:59:31.818	info	starting. Version 5.0.11 in /opt/iobroker/node_modules/iobroker.modbus, node: v16.19.1, js-controller: 4.0.24

Klemme wieder zurück!

Homoran

@metaxa sagte in M-TEC Energy Butler:

Klemme wieder zurück!

ja! wie blinkt es denn?

metaxa

@homoran sagte in M-TEC Energy Butler:

wie blinkt es denn?

Kurz nur die rechte LED flackert nach dem Bestromen blau hört aber nach 2 Sekunden wieder auf und bleibt finster, links Power bleibt brav rot.

Homoran

@metaxa der müsste jede Sekunde Blinken.
Brauchst du so viele Daten? sonst setz das Intervall runter 5000msec müssten vollkommen reichen.

metaxa

@homoran
Habe jetzt wieder zurückgeklemmt, paar von diesen 16Bit Einträgen ausprobiert, es kommt immer dieser "Wrong SRC for frame"

modbus.0
2023-06-23 22:16:39.630	debug	[DevID_247] Poll start ---------------------

modbus.0
2023-06-23 22:16:37.896	error	Wrong CRC for frame: 247,3,117,248,0,60,202,176,247,3,120,9,71,0,3,19,134,0,0,0,0,0,41,0,0,0,0,0,0,0,0,9,64,0,38,19,136,0,0,0,0,2,161,0,0,0,0,0,0,0,0,9,74,0,3,19,138,0,0,0,0,0,28,0,0,0,0,0,0,0,0,0,0,2,230,0,0,0,0,0,0,0,0,0,0,0,83,0,0,0,0,0,0,0,0,0,0,2,173,0,0,0,0,0,0,0,0,0,0,0,83,0,0,0,0,0,0,0,0,9,27,0

modbus.0
2023-06-23 22:16:37.561	error	Error response: 28

modbus.0
2023-06-23 22:16:37.497	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 22:16:37.486	error	Wrong CRC for frame: 247,3,128,232,0,18,120,165,247,3,36,19,92,39,15,0,2,0,244,255,255,255,255,255,255,255,255,0,0,1,1,0,0,0,230,0,0,12,195,0,0,12,183,0,0,0,0,226,200,247,3,42,242,0,8,249,113,247,3,16,0,0,0,0,255,255,255,243,0,0,0,7,0,0,0,0,235,1,247,3,39,16,0,11,27,234,247,3,22,90,49,49,50,51,48,48,50,48,56,51,51,48,50,54,49,30,6,0,0,0,0,190,217,247,3,39,121,0,17,74,61,247,3,34,0,2,0,0,0,0,0,0,0

modbus.0
2023-06-23 22:16:35.088	error	Wrong CRC for frame: 247,3,117,248,0,60,202,176,247,3,120,9,67,0,5,19,134,0,0,0,0,0,42,0,0,0,0,0,0,0,0,9,67,0,36,19,134,0,0,0,0,2,166,0,0,0,0,0,0,0,0,9,74,0,3,19,138,0,0,0,0,0,27,0,0,0,0,0,0,0,0,0,0,2,235,0,0,0,0,0,0,0,0,0,0,0,83,0,0,0,0,0,0,0,0,0,0,2,184,0,0,0,0,0,0,0,0,0,0,0,85,0,0,0,0,0,0,0,0,9,28,0

modbus.0
2023-06-23 22:16:34.750	error	unknown function code: 0x28, 0xf7

modbus.0
2023-06-23 22:16:34.687	error	Wrong CRC for frame: 247,3,39,121,0,17,74,61,247,3,34,0,2,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

modbus.0
2023-06-23 22:16:34.589	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 22:16:34.574	error	Wrong CRC for frame: 247,3,42,242,0,8,249,113,247,3,16,0,0,0,0,0,0,0,13,0,0,0,7,0,0,0,26,115,95,247,3,39,16,0,11,27,234,247,3,22,90,49,49,50,51,48,48

modbus.0
2023-06-23 22:16:32.338	error	Error response: Value is not accepted by slave

modbus.0
2023-06-23 22:16:32.337	error	Error response for FCx119: Illegal Data Value

modbus.0
2023-06-23 22:16:32.275	error	Wrong CRC for frame: 247,3,117,248,0,60,202,176,247,3,120,9,69,0,5,19,134,0,0,0,0,0,42,0,0,0,0,0,0,0,0,9,62,0,35,19,134,0,0,0,0,2,162,0,0,0,0,0,0,0,0,9,76,0,2,19,134,0,0,0,0,0,27,0,0,0,0,0,0,0,0,0,0,2,231,0,0,0,0,0,0,0,0,0,0,0,84,0,0,0,0,0,0,0,0,0,0,2,237,0,0,0,0,0,0,0,0,0,0,0,85,0,0,0,0,0,0,0,0,9,28,0

modbus.0
2023-06-23 22:16:31.940	error	Error response: 28

modbus.0
2023-06-23 22:16:31.879	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 22:16:31.861	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 22:16:31.843	error	unknown function code: 0x3d, 0xf7

modbus.0
2023-06-23 22:16:31.835	error	unknown function code: 0x0, 0xbe

modbus.0
2023-06-23 22:16:31.766	error	Wrong CRC for frame: 247,3,42,242,0,8,249,113,247,3,16,0,0,0,0,0,0,0,20,0,0,0,7,0,0,0,33,149,28,247,3,39,16,0,11,27,234,247,3,22,90,49,49,50,51,48,48

modbus.0
2023-06-23 22:16:29.577	warn	Poll error count: 1 code: "ReadInputRegisters: Invalid FC 3"

modbus.0
2023-06-23 22:16:29.527	error	Error response: f7

modbus.0
2023-06-23 22:16:29.468	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 22:16:29.447	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 22:16:29.432	error	unknown function code: 0x53, 0x0

modbus.0
2023-06-23 22:16:29.416	error	unknown function code: 0x0, 0x0

modbus.0
2023-06-23 22:16:29.400	error	unknown function code: 0x13, 0x86

modbus.0
2023-06-23 22:16:29.384	error	unknown function code: 0x0, 0x2

modbus.0
2023-06-23 22:16:29.371	error	Wrong CRC for frame: 0,3,247,3,39,16,0,11,27,234,247,3,22,90,49,49,50,51,48,48,50,48,56,51,51,48,50,54,49,30,6,0,0,0,0,190,217,247,3,39,121,0,17,74,61,247,3,34,0,2,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,215,40,247,3,42,254,0,60,56,165,247,3,120,16,25,16,24,16,29,9,73,0,9,9,76,0,32,9,77,0,10,19,135,0,0,3,1,0,0,1,41,0,0,1,134,0,0,0,31,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,176,1,190,1,161,1,190,30,63,15,30,0,0,0,1,0,0,0,1,78,32,78,6,78,45,0,0,41,187,0,0,0,2,81,199,15,255,0,15,1,1,0,64,30,163,30,163,19,93,48,56,10,8,41,4,1,1,0,0,0,0,0,0,0,0,0,0,245,199,247,3,117,248,0,60,202,176,247,3,120,9,68,0,5,19,134,0,0,0,0,0,42,0,0,0,0,0,0,0,0,9,66,0,37

modbus.0
2023-06-23 22:16:28.445	debug	[DevID_247/inputRegs] Poll address 2999 - 1 registers

modbus.0
2023-06-23 22:16:28.444	debug	Initialization of scale factors done!

modbus.0
2023-06-23 22:16:28.440	debug	[DevID_247] Poll start ---------------------

modbus.0
2023-06-23 22:16:28.438	info	Connected to slave

modbus.0
2023-06-23 22:16:28.415	debug	connect to serial /dev/ttyUSB1 with 9600

modbus.0
2023-06-23 22:16:27.710	debug	Initialize Objects for holdingRegs: []

modbus.0
2023-06-23 22:16:27.709	debug	Add inputRegisters.2999_State_of_Charge_(SOC): {"_id":"inputRegisters.2999_State_of_Charge_(SOC)","type":"state","common":{"name":"Ladezustand der Batterie","role":"level","type":"number","read":true,"write":false,"def":0,"unit":"%"},"native":{"regType":"inputRegs","address":2999,"deviceId":247,"type":"int16le","len":1,"offset":0,"factor":1}}

modbus.0
2023-06-23 22:16:27.708	debug	Initialize Objects for inputRegs: [{"_address":2999,"name":"State of Charge (SOC)","description":"Ladezustand der Batterie","unit":"%","type":"int16le","len":1,"factor":1,"offset":0,"formula":"","role":"level","room":"","cw":false,"isScale":"","address":2999,"deviceId":247,"id":"inputRegisters.2999_State_of_Charge_(SOC)"}]

modbus.0
2023-06-23 22:16:27.707	debug	Initialize Objects for coils: []

modbus.0
2023-06-23 22:16:27.706	debug	Initialize Objects for disInputs: []

modbus.0
2023-06-23 22:16:27.222	info	starting. Version 5.0.11 in /opt/iobroker/node_modules/iobroker.modbus, node: v16.19.1, js-controller: 4.0.24

alais Checkbox hat nix verändert.

metaxa

Kann ich aus dem LOG erkennen ob da am anderen Ende überhaupt Daten sind, die Busschnittstelle die richtige ist?

Homoran

@metaxa das versuche ich die ganze Zeit zu erkennen.
was sagt denn lsusb?

metaxa

@homoran sagte in M-TEC Energy Butler:

lsusb

andreas@iOProduktiv:~$ lsusb -t
/:  Bus 07.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
/:  Bus 06.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
/:  Bus 05.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 5000M
/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
    |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=ch341, 12M
    |__ Port 2: Dev 5, If 0, Class=Vendor Specific Class, Driver=ftdi_sio, 12M
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 480M
    |__ Port 1: Dev 2, If 0, Class=Human Interface Device, Driver=usbfs, 12M
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
    |__ Port 1: Dev 2, If 0, Class=Human Interface Device, Driver=usbhid, 12M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/6p, 480M


andreas@iOProduktiv:~$ ls -l /dev/serial/by-id
insgesamt 0
lrwxrwxrwx 1 root root 13 23. Jun 19:53 usb-1a86_USB_Serial-if00-port0 -> ../../ttyUSB0
lrwxrwxrwx 1 root root 13 23. Jun 22:09 usb-FTDI_FT232R_USB_UART_A10N5R2A-if00-port0 -> ../../ttyUSB1
andreas@iOProduktiv:~$

Homoran

@metaxa was hängt denn noch dran?

pi@tinkerboard:~$ ls -l /dev/serial/by-id
insgesamt 0
lrwxrwxrwx 1 root root 13 14. Mai 22:54 usb-FTDI_FT232R_USB_UART_A10NBMVW-if00-port0 -> ../../ttyUSB1
lrwxrwxrwx 1 root root 13 14. Mai 22:53 usb-FTDI_FT232R_USB_UART_AB0OH9QR-if00-port0 -> ../../ttyUSB2
lrwxrwxrwx 1 root root 13 14. Mai 22:53 usb-Silicon_Labs_CP2104_USB_to_UART_Bridge_Controller_01066523-if00-port0 -> ../../ttyUSB0

ich hab 2 dran

Community Forum

NEWS

M-TEC Energy Butler

Support us

759

32.5k

81.7k

1.3m