Sammlung Informationen Wallbox & ioBroker-Integration

[Sneak-L8]

@darkiop Die Ladung startet mit 6A, die Leistung hängt von der Anzahl der Phasen ab. Da man das vorab nicht wissen kann, merkt sch der Adapter, mit wieviel Phasen zuletzt geladen wurde und geht bei zuküftigen Ladungen davon aus, dass es sich um ebensoviele Phasne handelt.
Bei drei Phasen müssen also über 4kW Überschuss vorhanden sein, damit das Laden beginnt. Bei einer Phase reichen 1,38 kW.
Die von Dir zitierten 10A sind der per DIP-Schalter konfigurierbare maximal Stromstärke. Du kannst die Anlage also z.B. auf 10A begrenzen, dann kann man nie mehr als mit 10A laden.

Die von Dir gewählten werte sind so in Ordnung. Die 3000W, die er auch dauerhaft aus dem Netz ziehen darf, bevor die Ladung beendet wird ist aber recht viel. Bei einphasigem Laden würde die Ladung so gar nicht beendet (er regelt ja ggf.s auf 6 A runter und zieht dann auch bei 0 W PV "nur" 1.380W aus dem Netz...

[ChristianF]

Nur mal so als kleiner Hinweis für alle, die mit einer Ethernetverbindung überlegen...

• Damit legt ihr einen direkten Netzwerkport außerhalb Eures Hauses bereit
• Gerade wenn sicherheitsrelevante Systeme wie Alarmanlagen usw in ioB integriert sind, wird das ein mega Sicherheitsloch
• Hier sollte man sich sehr genau überlegen, was man nach aussen legt und wie der Port abgeschirmt wird (Firewall, VLAN etc.)

Eine Anbindung via Modbus-serial ist vielleicht nicht so super sexy, aber deutlich sicherer und wenn galvanisch getrennt auch elektrisch stabiler. Wenn es unbedingt Ethernet sein soll, dann lieber WLAN (möglichst ohne Cloudsteuerung).

Es geht hier übrigens weniger um die tagtäglichen Einbrecherbanden die nur schnell raffen und weg wollen, sondern um die die längerfristig ein Objekt ausspähen, warten bis länger niemand da ist und dann loslegen. Das Schlimme ist, dass ihr das mit Pech noch nicht mal mitkriegt (Kabel auftrennen, Mini-Hub dran, Verbindung zwischen Haus und WB wieder herstellen damit keiner Verdacht schöpft und ein kleines LTE- oder WLAN Modul mit dran hängen damit man aus sicherer Entfernung in aller Ruhe das Hausnetz auseinandernehmen kann.. ja, mag vielleicht paranoid sein, ich glaube aber dass das nicht unrealistisch ist.. und wenn nicht heute, dann vielleicht in 1-2-3 Jahren..

[lemuba]

@homoran sagte in Sammlung Informationen Wallbox & ioBroker-Integration:

@lobomau sagte in Sammlung Informationen Wallbox & ioBroker-Integration:

Geht eigentlich allles, der Go-echarger kann von 6-32 A regeln.

ok - das reicht, wobei 6A ja schon 1380 Watt sind.
Im MOmnet sind die "Überschüsse" selten 4stellig

@lobomau sagte in Sammlung Informationen Wallbox & ioBroker-Integration:

Was der Go-echarger nicht kann ist Umschalten zw. 1 und 3 Phasen.

Das hängt ja auch beim mobilen Modell von den Adapterkabeln ab. Steckdose mit 16A kann ja auch keine 3 Phasen liefern

@Homoran Wie schaut denn jetzt Dein geplantes Setup für den ZOE aus? Und welche Wallbox?

Meine geplante 26,5KWp Anlage wird nun wohl spätestens am 1. Mai ans Netz gehen. Dazu kommt dann ein Renault Twingo Elektro. SMA Wechselrichter, Sunny Homemanger 2.0, und dann wahrscheinlich auch die SMA Wallbox, da die (im Gegensatz zur OpenWB) anscheinend auch ZOE kompatibel ist, bzw. so zwischen 3phasigem und 1phasigem PV-Überschuss Laden umschalteten kann, ohne den ZOE internen Lader zu schrotten. Wie es beim Twingo ausschaut muss ich noch rausfinden.

Was mich aber auch gerade bez. Renault generell abschreckt, zumindest beim ZOE nochmal genauer betrachten würde, die wohl grottenschlechte Ladeeffizienz bei reduzierten Stromstärken/Phase, Quelle:
https://openwb.de/forum/viewtopic.php?p=17307#p17307

Ist das für Dich relevant, bzw. hast Du das auf dem Zettel?

[Homoran]

@lemuba sagte in Sammlung Informationen Wallbox & ioBroker-Integration:

Wie schaut denn jetzt Dein geplantes Setup für den ZOE aus? Und welche Wallbox?

erst einmal nur einphasig 3.6kW über Steckdose.
Dann vielleicht (erst mal zusätzlich auch über Adapter) go-e charger.

[Qlink]

Hi Leute,

ich habe heute ebenfalls den Keba KeContact Adapter versucht in den Regelungsmodus zu versetzen.
Ich hatte ihn bisher nur im passiven Modus in Betrieb.

Folgendes habe ich im Adapter eingestellt:

Leider schauts so aus, als ob ihm diese Einstellungen ziemlich egal sind. Er regelt den Ladestrom von aktuell 20A nicht runter, obwohl schon Netzbezug passiert, also kein Überschuss mehr vorhanden ist.

Habe ich die Werte falsch eingegeben oder falsch verstanden, oder habe ich was übersehen ?

Danke.

Beste Grüße

P.S. wenn ich manuell über den KeContact Adapter den Datenpunkt UserCurrent auf 5000mA setze, dann übernimmt er den auch kurz und ich habe wieder eine Überschusseinspeisung, aber nach dem nächsten Aktualisierungsintervall (30s) geht er wieder auf die 20A Ladestrom und eben Netzbezug ... Wie wenn irgendeine Einstellung die automatische Regelung immer wieder overruled ...

[Sneak-L8]

@qlink Du hast einen relativ hohen dauerhaften Netzbezug eingestellt. 5.000W. D.h. zusätzlich zum PV-Überschuss nimmst zu immer zusätzlich 5.000W aus dem Netz dazu. Das erscheint mir deutlich zu hoch.
Mit wieviel Phasen lädst Du?

Die Einschalt-Ampere von 5.000mA kannst Du Dir sparen. Die Box kann nur minimal 6A. Sieht du auch im Log.
Oder waren die schon Default gesetzt? Dann müsste ich mal nachschauen, ob das falsch hinterlegt ist.

Das bitte auch mal das Log und die installierte Version posten.

[Qlink]

@sneak-l8

Alles klar, dann habe ich den Wert falsch interpretiert, das ist natürlich viel zu hoch.
Ich lade mit 3 Phasen.

Habs jetzt mal auf folgende Werte abgeändert:

Hier noch der iobroker Log output:

kecontact.0	2021-03-25 14:54:17.980	info	(5168) minimum amperage not speficied or too low, using default value of 6000
kecontact.0	2021-03-25 14:54:17.980	info	(5168) starting charging station in active mode
kecontact.0	2021-03-25 14:54:12.959	info	(5168) starting. Version 1.1.1 in C:/iobroker/iob01/node_modules/iobroker.kecontact, node: v10.17.0, js-controller: 3.2.16
host.iob01	2021-03-25 14:54:12.006	info	instance system.adapter.kecontact.0 started with pid 5168
host.iob01	2021-03-25 14:54:09.610	info	instance system.adapter.kecontact.0 terminated with code 11 (ADAPTER_REQUESTED_TERMINATION)
kecontact.0	2021-03-25 14:54:08.980	info	(1712) Terminated (ADAPTER_REQUESTED_TERMINATION): Without reason
kecontact.0	2021-03-25 14:54:08.980	info	(1712) terminating
host.iob01	2021-03-25 14:54:08.981	info	stopInstance system.adapter.kecontact.0 send kill signal

Er regelt aber leider immer noch nicht ...

[Sneak-L8]

@qlink Hm, sieht soweit gut aus. IP-Adresse dürfte auch korrekt sein, sonst hätte sich die Wallbox auch passiv nicht regeln lassen.

Ach so, ist das Auto angesteckt? Es zeigt so gar nichts an. sonst den Adapter mal auf debug steleln und das log posten.

[Qlink]

@sneak-l8

Ja Auto ist angesteckt und lädt auch brav.

Hier mal ein kleiner Auszug aus dem Log mit debug:

2021-03-25 15:13:26.493 - debug: kecontact.0 (9160) Redis Objects: Use Redis connection: 127.0.0.1:9001
2021-03-25 15:13:26.524 - debug: kecontact.0 (9160) Objects client ready ... initialize now
2021-03-25 15:13:26.524 - debug: kecontact.0 (9160) Objects create System PubSub Client
2021-03-25 15:13:26.540 - debug: kecontact.0 (9160) Objects create User PubSub Client
2021-03-25 15:13:26.540 - debug: kecontact.0 (9160) Objects client initialize lua scripts
2021-03-25 15:13:26.555 - debug: kecontact.0 (9160) Objects connected to redis: 127.0.0.1:9001
2021-03-25 15:13:26.555 - debug: kecontact.0 (9160) objectDB connected
2021-03-25 15:13:26.555 - debug: kecontact.0 (9160) Redis States: Use Redis connection: 127.0.0.1:9000
2021-03-25 15:13:26.571 - debug: kecontact.0 (9160) States create System PubSub Client
2021-03-25 15:13:26.571 - debug: kecontact.0 (9160) States create User PubSub Client
2021-03-25 15:13:26.571 - debug: kecontact.0 (9160) States connected to redis: 127.0.0.1:9000
2021-03-25 15:13:26.571 - debug: kecontact.0 (9160) statesDB connected
2021-03-25 15:13:26.805 - info: kecontact.0 (9160) starting. Version 1.1.1 in C:/iobroker/iob01/node_modules/iobroker.kecontact, node: v10.17.0, js-controller: 3.2.16
2021-03-25 15:13:31.854 - info: kecontact.0 (9160) starting charging station in active mode
2021-03-25 15:13:31.854 - info: kecontact.0 (9160) minimum amperage not speficied or too low, using default value of 6000
2021-03-25 15:13:31.854 - debug: kecontact.0 (9160) UDP server listening on 0.0.0.0:7090
2021-03-25 15:13:31.854 - debug: kecontact.0 (9160) UDP broadcast server listening on 0.0.0.0:7092
2021-03-25 15:13:31.854 - debug: kecontact.0 (9160) subscribe state sma-em.0.1901701237.pregard - current value: 1762.6000000000001
2021-03-25 15:13:31.854 - debug: kecontact.0 (9160) update state kecontact.0.sma-em.0.1901701237.pregard with value:1762.6000000000001
2021-03-25 15:13:31.854 - debug: kecontact.0 (9160) subscribe state sma-em.0.1901701237.psurplus - current value: 0
2021-03-25 15:13:31.854 - debug: kecontact.0 (9160) update state kecontact.0.sma-em.0.1901701237.psurplus with value:0
2021-03-25 15:13:32.089 - debug: kecontact.0 (9160) Sent "i" to 192.168.30.15:7090
2021-03-25 15:13:32.089 - debug: kecontact.0 (9160) UDP datagram from 192.168.30.15:7090: ""Firmware":"P30 v 3.10.16 (200708-201734)""
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.eTotal with value:64303.1
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.ePres with value:13857.7
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.pf with value:99.5
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.p with value:5787722
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.i3 with value:8159
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.i2 with value:8181
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.i1 with value:8160
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.u3 with value:235
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.u2 with value:240
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.u1 with value:236
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.uptime with value:1399438
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.input with value:false
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.output with value:false
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.timeoutFailsafe with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.currentFailsafe with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.currentUser with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.currentHardware with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.maxCurrentPercent with value:33.3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.maxCurrent with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.enableUser with value:true
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.enableSys with value:true
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.plug with value:7
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.error2 with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.error1 with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.state with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.firmware with value:P30 v 3.10.16 (200708-201734)
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.serial with value:20296767
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.product with value:KC-P30-ES2400B2-M0R
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.automatic.pauseWallbox with value:false
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.automatic.photovoltaics with value:false
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.statistics.plugTimestamp with value:2021-03-25T11:37:39.198Z
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.statistics.chargeTimestamp with value:2021-03-25T13:25:22.882Z
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.statistics.lastChargeStart with value:2021-03-19T14:33:49.664Z
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.statistics.lastChargeFinish with value:2021-03-19T17:37:36.521Z
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.statistics.lastChargeAmount with value:18.1553
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.COM-module with value:true
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.backend with value:false
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.timeQ with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.DIP-Sw1 with value:0x26
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.DIP-Sw2 with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.currentTimer with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.timeoutCurrentTimer with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.setenergy with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.authON with value:false
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.authreq with value:false
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.automatic.addPower with value:500
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.statistics.surplus with value:null
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.statistics.maxPower with value:false
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.statistics.chargingPhases with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.json with value:[{"ID":"100","Session ID":8,"Curr HW":20000,"E start":504454,"E pres":138584,"started[s]":1616672249,"ended[s]":0,"started":"2021-03-25 11:37:29.000","ended":"0","reason":0,"timeQ":0,"RFID tag":"0000000000000000","RFID class":"9b07e84a000000000000","Serial":"20296767","Sec":1399438}]
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.sessionid with value:8
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.currentHardware with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.eStart with value:50445.4
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.ePres with value:13858.4
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.started_s with value:1616672249
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.ended_s with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.started with value:2021-03-25 11:37:29.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.ended with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.reason with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.timeQ with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.rfid_class with value:9b07e84a000000000000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.serial with value:20296767
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_00.sec with value:1399438
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.json with value:[{"ID":"101","Session ID":7,"Curr HW":20000,"E start":322901,"E pres":181553,"started[s]":1616164422,"ended[s]":1616175449,"started":"2021-03-19 14:33:42.000","ended":"2021-03-19 17:37:29.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"fe1e8b2b000000000000","Serial":"20296767","Sec":1399438}]
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.sessionid with value:7
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.currentHardware with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.eStart with value:32290.1
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.ePres with value:18155.3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.started_s with value:1616164422
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.ended_s with value:1616175449
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.started with value:2021-03-19 14:33:42.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.ended with value:2021-03-19 17:37:29.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.reason with value:1
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.timeQ with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.rfid_class with value:fe1e8b2b000000000000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.serial with value:20296767
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_01.sec with value:1399438
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.json with value:[{"ID":"102","Session ID":6,"Curr HW":20000,"E start":222666,"E pres":100235,"started[s]":1615638239,"ended[s]":1615648318,"started":"2021-03-13 12:23:59.000","ended":"2021-03-13 15:11:58.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"76e4d316000000000000","Serial":"20296767","Sec":1399439}]
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.sessionid with value:6
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.currentHardware with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.eStart with value:22266.6
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.ePres with value:10023.5
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.started_s with value:1615638239
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.ended_s with value:1615648318
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.started with value:2021-03-13 12:23:59.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.ended with value:2021-03-13 15:11:58.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.reason with value:1
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.timeQ with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.rfid_class with value:76e4d316000000000000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.serial with value:20296767
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_02.sec with value:1399439
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.json with value:[{"ID":"103","Session ID":5,"Curr HW":20000,"E start":181890,"E pres":40776,"started[s]":1615290689,"ended[s]":1615294745,"started":"2021-03-09 11:51:29.000","ended":"2021-03-09 12:59:05.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"76e4d316000000000000","Serial":"20296767","Sec":1399439}]
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.sessionid with value:5
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.currentHardware with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.eStart with value:18189
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.ePres with value:4077.6
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.started_s with value:1615290689
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.ended_s with value:1615294745
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.started with value:2021-03-09 11:51:29.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.ended with value:2021-03-09 12:59:05.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.reason with value:1
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.timeQ with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.rfid_class with value:76e4d316000000000000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.serial with value:20296767
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_03.sec with value:1399439
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.json with value:[{"ID":"104","Session ID":4,"Curr HW":20000,"E start":133509,"E pres":48381,"started[s]":1615207786,"ended[s]":1615212627,"started":"2021-03-08 12:49:46.000","ended":"2021-03-08 14:10:27.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"b9ca830c000000000000","Serial":"20296767","Sec":1399439}]
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.sessionid with value:4
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.currentHardware with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.eStart with value:13350.9
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.ePres with value:4838.1
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.started_s with value:1615207786
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.ended_s with value:1615212627
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.started with value:2021-03-08 12:49:46.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.ended with value:2021-03-08 14:10:27.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.reason with value:1
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.timeQ with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.rfid_class with value:b9ca830c000000000000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.serial with value:20296767
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_04.sec with value:1399439
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.json with value:[{"ID":"105","Session ID":3,"Curr HW":20000,"E start":32654,"E pres":100855,"started[s]":1615117666,"ended[s]":1615127564,"started":"2021-03-07 11:47:46.000","ended":"2021-03-07 14:32:44.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"82c4800c000000000000","Serial":"20296767","Sec":1399439}]
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.sessionid with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.currentHardware with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.eStart with value:3265.4
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.ePres with value:10085.5
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.started_s with value:1615117666
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.ended_s with value:1615127564
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.started with value:2021-03-07 11:47:46.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.ended with value:2021-03-07 14:32:44.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.reason with value:1
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.timeQ with value:3
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.rfid_class with value:82c4800c000000000000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.serial with value:20296767
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_05.sec with value:1399439
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.json with value:[{"ID":"106","Session ID":2,"Curr HW":20000,"E start":32654,"E pres":0,"started[s]":1615117466,"ended[s]":1615117659,"started":"2021-03-07 11:44:26.000","ended":"2021-03-07 11:47:39.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"fdfe073f000000000000","Serial":"20296767","Sec":1399440}]
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.sessionid with value:2
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.currentHardware with value:20000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.eStart with value:3265.4
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.ePres with value:0
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.started_s with value:1615117466
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.ended_s with value:1615117659
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.started with value:2021-03-07 11:44:26.000
2021-03-25 15:13:32.120 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.ended with value:2021-03-07 11:47:39.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.reason with value:1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.timeQ with value:3
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.rfid_class with value:fdfe073f000000000000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_06.sec with value:1399440
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.json with value:[{"ID":"107","Session ID":1,"Curr HW":20000,"E start":2269,"E pres":30385,"started[s]":1613817709,"ended[s]":1613818767,"started":"2021-02-20 10:41:49.000","ended":"2021-02-20 10:59:27.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"fdfe073f000000000000","Serial":"20296767","Sec":1399440}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.sessionid with value:1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.currentHardware with value:20000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.eStart with value:226.9
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.ePres with value:3038.5
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.started_s with value:1613817709
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.ended_s with value:1613818767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.started with value:2021-02-20 10:41:49.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.ended with value:2021-02-20 10:59:27.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.reason with value:1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.timeQ with value:3
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.rfid_class with value:fdfe073f000000000000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_07.sec with value:1399440
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.json with value:[{"ID":"108","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399440}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_08.sec with value:1399440
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.json with value:[{"ID":"109","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399441}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_09.sec with value:1399441
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.json with value:[{"ID":"110","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399441}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_10.sec with value:1399441
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.json with value:[{"ID":"111","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399441}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_11.sec with value:1399441
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.json with value:[{"ID":"112","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399412}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_12.sec with value:1399412
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.json with value:[{"ID":"113","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399412}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_13.sec with value:1399412
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.json with value:[{"ID":"114","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399412}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_14.sec with value:1399412
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.json with value:[{"ID":"115","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399413}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_15.sec with value:1399413
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.json with value:[{"ID":"116","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399413}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_16.sec with value:1399413
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.json with value:[{"ID":"117","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399413}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_17.sec with value:1399413
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.json with value:[{"ID":"118","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399414}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_18.sec with value:1399414
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.json with value:[{"ID":"119","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399414}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_19.sec with value:1399414
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.json with value:[{"ID":"120","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399414}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_20.sec with value:1399414
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.json with value:[{"ID":"121","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399414}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_21.sec with value:1399414
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.json with value:[{"ID":"122","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399415}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.serial with value:20296767
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_22.sec with value:1399415
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.json with value:[{"ID":"123","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399415}]
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.sessionid with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.currentHardware with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.eStart with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.ePres with value:-0.1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.started_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.ended_s with value:-1
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.reason with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.timeQ with value:255
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.136 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.serial with value:20296767
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_23.sec with value:1399415
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.json with value:[{"ID":"124","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399415}]
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.sessionid with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.currentHardware with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.eStart with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.ePres with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.started_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.ended_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.reason with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.timeQ with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.serial with value:20296767
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_24.sec with value:1399415
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.json with value:[{"ID":"125","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399416}]
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.sessionid with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.currentHardware with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.eStart with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.ePres with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.started_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.ended_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.reason with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.timeQ with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.serial with value:20296767
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_25.sec with value:1399416
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.json with value:[{"ID":"126","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399416}]
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.sessionid with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.currentHardware with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.eStart with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.ePres with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.started_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.ended_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.reason with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.timeQ with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.serial with value:20296767
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_26.sec with value:1399416
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.json with value:[{"ID":"127","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399416}]
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.sessionid with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.currentHardware with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.eStart with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.ePres with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.started_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.ended_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.reason with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.timeQ with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.serial with value:20296767
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_27.sec with value:1399416
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.json with value:[{"ID":"128","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399417}]
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.sessionid with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.currentHardware with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.eStart with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.ePres with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.started_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.ended_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.reason with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.timeQ with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.serial with value:20296767
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_28.sec with value:1399417
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.json with value:[{"ID":"129","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399417}]
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.sessionid with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.currentHardware with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.eStart with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.ePres with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.started_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.ended_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.reason with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.timeQ with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.serial with value:20296767
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_29.sec with value:1399417
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.json with value:[{"ID":"130","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1399417}]
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.sessionid with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.currentHardware with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.eStart with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.ePres with value:-0.1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.started_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.ended_s with value:-1
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.started with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.ended with value:2106-02-07 06:28:15.000
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.reason with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.timeQ with value:255
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.rfid_class with value:ffffffffffffffffffff
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.serial with value:20296767
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) update state kecontact.0.Sessions.Session_30.sec with value:1399417
2021-03-25 15:13:32.151 - debug: kecontact.0 (9160) wallbox set to charging maximum of 20000 mA
2021-03-25 15:13:32.167 - debug: kecontact.0 (9160) stateChange kecontact.0.firmware {"val":"P30 v 3.10.16 (200708-201734)","ack":true,"ts":1616681612104,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1604251750835}
2021-03-25 15:13:32.183 - debug: kecontact.0 (9160) update state kecontact.0.firmware with value:P30 v 3.10.16 (200708-201734)
2021-03-25 15:13:32.214 - debug: kecontact.0 (9160) stateChange kecontact.0.statistics.chargingPhases {"val":3,"ack":true,"ts":1616681612214,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1616678722882}
2021-03-25 15:13:32.214 - debug: kecontact.0 (9160) update state kecontact.0.statistics.chargingPhases with value:3
2021-03-25 15:13:32.214 - debug: kecontact.0 (9160) stateChange sma-em.0.1901701237.pregard {"val":1814.2,"ack":true,"ts":1616681612213,"q":0,"from":"system.adapter.sma-em.0","user":"system.user.admin","lc":1616681612213}
2021-03-25 15:13:32.214 - debug: kecontact.0 (9160) update state kecontact.0.sma-em.0.1901701237.pregard with value:1814.2
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) Sent "report 1" to 192.168.30.15:7090
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) UDP datagram from 192.168.30.15:7090: "{
"ID": "1",
"Product": "KC-P30-ES2400B2-M0R",
"Serial": "20296767",
"Firmware":"P30 v 3.10.16 (200708-201734)",
"COM-module": 1,
"Backend": 0,
"timeQ": 3,
"DIP-Sw1": "0x26",
"DIP-Sw2": "0x00",
"Sec": 1399451
}
"
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) stateChange kecontact.0.product {"val":"KC-P30-ES2400B2-M0R","ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1604251751148}
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) update state kecontact.0.product with value:KC-P30-ES2400B2-M0R
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) stateChange kecontact.0.serial {"val":"20296767","ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1604251751148}
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) update state kecontact.0.serial with value:20296767
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) stateChange kecontact.0.firmware {"val":"P30 v 3.10.16 (200708-201734)","ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1604251750835}
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) update state kecontact.0.firmware with value:P30 v 3.10.16 (200708-201734)
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) stateChange kecontact.0.COM-module {"val":true,"ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1615267231548}
2021-03-25 15:13:32.401 - debug: kecontact.0 (9160) update state kecontact.0.COM-module with value:true
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) stateChange kecontact.0.backend {"val":false,"ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1615267231548}
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) update state kecontact.0.backend with value:false
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) stateChange kecontact.0.timeQ {"val":3,"ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1615267231548}
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) update state kecontact.0.timeQ with value:3
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) stateChange kecontact.0.DIP-Sw1 {"val":"0x26","ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1615267231548}
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) update state kecontact.0.DIP-Sw1 with value:0x26
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) stateChange kecontact.0.DIP-Sw2 {"val":0,"ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1615267231548}
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) update state kecontact.0.DIP-Sw2 with value:0
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) stateChange kecontact.0.uptime {"val":1399451,"ack":true,"ts":1616681612401,"q":0,"from":"system.adapter.kecontact.0","user":"system.user.admin","lc":1616681612401}
2021-03-25 15:13:32.417 - debug: kecontact.0 (9160) update state kecontact.0.uptime with value:1399451
2021-03-25 15:13:32.717 - debug: kecontact.0 (9160) Sent "report 2" to 192.168.30.15:7090
2021-03-25 15:13:32.717 - debug: kecontact.0 (9160) UDP datagram from 192.168.30.15:7090: "{
"ID": "2",
"State": 3,
"Error1": 0,
"Error2": 0,
"Plug": 7,
"AuthON": 0,
"Authreq": 0,
"Enable sys": 1,
"Enable user": 1,
"Max curr": 20000,
"Max curr %": 333,
"Curr HW": 20000,
"Curr user": 20000,
"Curr FS": 0,
"Tmo FS": 0,
"Curr timer": 20000,
"Tmo CT": 0,
"Setenergy": 0,
"Output": 0,
"Input": 0,
"Serial": "20296767",
"Sec": 1399451
}
"

[Sneak-L8]

@qlink Hm, so ganz komme ich nicht dahinter. Kannst Du mal das Auto abstecken, den Adapter neu starten und erst danach wieder anstecken? Das ist das einzige das mir gerade einfällt. Evtl. aktiviert er die zyklische Prüfung des Überschusses nicht, wenn das Auto beim Start schon angesteckt war.
Das lässt sich dann korrigiert, köntne aber aktuell die Ursache sein.

[Qlink]

@sneak-l8

Das hätte ich auch gerade probiert.
Hat leider auch nix gebracht.
Selbes Bild.
Er lädt mit 8A (Begrenzung eingestellt im Auto), obwohl dadurch ein Netzbezug von aktuell 800W verursacht wird...
Für mein Verständnis sollte er ja automatisch auf 7A oder 6A runterregeln, damit eben eine minimale Netzeinspeisung übrig bleibt richtig ?

[Sneak-L8]

@qlink Komisch.

Kannst Du das nochmal wiederholen und ein Debug-Log machen? Das Log hier bitte mit der Spoiler-Funktion (Das Icon mit dem Auge) nutzen, damit es defaultmäßig ausgeblendet wird.
UDP-Funktion der Wallbox ist ja aktiviert. Ist es korrekt, dass sie auf 20A abgeregelt ist?

[Qlink]

@sneak-l8

@sneak-l8

done

Kann es sein, dass er eventuell die Werte von meinem Energymeter nicht richtig interpretieren kann, sprich das die im falschen Format sind oder sowas ähnliches ?

Spoiler

2021-03-26 09:49:36.408  - info: host.iob01 stopInstance system.adapter.kecontact.0 (force=false, process=true)
2021-03-26 09:49:36.424  - info: kecontact.0 (1448) Got terminate signal TERMINATE_YOURSELF
2021-03-26 09:49:36.424  - info: kecontact.0 (1448) terminating
2021-03-26 09:49:36.424  - info: kecontact.0 (1448) Terminated (ADAPTER_REQUESTED_TERMINATION): Without reason
2021-03-26 09:49:36.424  - info: host.iob01 stopInstance system.adapter.kecontact.0 send kill signal
2021-03-26 09:49:37.044  - info: host.iob01 instance system.adapter.kecontact.0 terminated with code 11 (ADAPTER_REQUESTED_TERMINATION)
2021-03-26 09:49:39.441  - info: host.iob01 instance system.adapter.kecontact.0 started with pid 2236
2021-03-26 09:49:40.130  - debug: kecontact.0 (2236) Redis Objects: Use Redis connection: 127.0.0.1:9001
2021-03-26 09:49:40.145  - debug: kecontact.0 (2236) Objects client ready ... initialize now
2021-03-26 09:49:40.145  - debug: kecontact.0 (2236) Objects create System PubSub Client
2021-03-26 09:49:40.161  - debug: kecontact.0 (2236) Objects create User PubSub Client
2021-03-26 09:49:40.161  - debug: kecontact.0 (2236) Objects client initialize lua scripts
2021-03-26 09:49:40.161  - debug: kecontact.0 (2236) Objects connected to redis: 127.0.0.1:9001
2021-03-26 09:49:40.177  - debug: kecontact.0 (2236) objectDB connected
2021-03-26 09:49:40.177  - debug: kecontact.0 (2236) Redis States: Use Redis connection: 127.0.0.1:9000
2021-03-26 09:49:40.177  - debug: kecontact.0 (2236) States create System PubSub Client
2021-03-26 09:49:40.177  - debug: kecontact.0 (2236) States create User PubSub Client
2021-03-26 09:49:40.192  - debug: kecontact.0 (2236) States connected to redis: 127.0.0.1:9000
2021-03-26 09:49:40.192  - debug: kecontact.0 (2236) statesDB connected
2021-03-26 09:49:40.458  - info: kecontact.0 (2236) starting. Version 1.1.1 in C:/iobroker/iob01/node_modules/iobroker.kecontact, node: v10.17.0, js-controller: 3.2.16
2021-03-26 09:49:45.483  - info: kecontact.0 (2236) starting charging station in active mode
2021-03-26 09:49:45.483  - info: kecontact.0 (2236) minimum amperage not speficied or too low, using default value of 6000
2021-03-26 09:49:45.483  - debug: kecontact.0 (2236) UDP server listening on 0.0.0.0:7090
2021-03-26 09:49:45.483  - debug: kecontact.0 (2236) UDP broadcast server listening on 0.0.0.0:7092
2021-03-26 09:49:45.483  - debug: kecontact.0 (2236) subscribe state sma-em.0.1901701237.pregard - current value: 0
2021-03-26 09:49:45.483  - debug: kecontact.0 (2236) update state kecontact.0.sma-em.0.1901701237.pregard with value:0
2021-03-26 09:49:45.483  - debug: kecontact.0 (2236) subscribe state sma-em.0.1901701237.psurplus - current value: 5270.200000000001
2021-03-26 09:49:45.483  - debug: kecontact.0 (2236) update state kecontact.0.sma-em.0.1901701237.psurplus with value:5270.200000000001
2021-03-26 09:49:45.702  - debug: kecontact.0 (2236) Sent "i" to 192.168.30.15:7090
2021-03-26 09:49:45.702  - debug: kecontact.0 (2236) UDP datagram from 192.168.30.15:7090: ""Firmware":"P30 v 3.10.16 (200708-201734)""
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.eTotal with value:66878.1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.ePres with value:1378
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.pf with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.p with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.i3 with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.i2 with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.i1 with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.u3 with value:235
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.u2 with value:238
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.u1 with value:236
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.uptime with value:1466410
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.input with value:false
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.output with value:false
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.timeoutFailsafe with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.currentFailsafe with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.currentUser with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.maxCurrentPercent with value:33.3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.maxCurrent with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.enableUser with value:true
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.enableSys with value:true
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.plug with value:7
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.error2 with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.error1 with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.state with value:2
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.firmware with value:P30 v 3.10.16 (200708-201734)
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.product with value:KC-P30-ES2400B2-M0R
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.display with value:volle Ladeleistung
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.automatic.pauseWallbox with value:false
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.automatic.photovoltaics with value:false
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.statistics.plugTimestamp with value:2021-03-26T08:33:36.975Z
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.statistics.chargeTimestamp with value:2021-03-26T08:34:08.222Z
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.statistics.lastChargeStart with value:2021-03-25T11:37:39.198Z
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.statistics.lastChargeFinish with value:2021-03-25T14:47:01.716Z
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.statistics.lastChargeAmount with value:15.0547
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.COM-module with value:true
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.backend with value:false
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.DIP-Sw1 with value:0x26
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.DIP-Sw2 with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.currentTimer with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.timeoutCurrentTimer with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.setenergy with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.authON with value:false
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.authreq with value:false
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.automatic.addPower with value:500
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.statistics.surplus with value:null
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.statistics.maxPower with value:false
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.statistics.chargingPhases with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.json with value:[{"ID":"100","Session ID":9,"Curr HW":20000,"E start":655001,"E pres":13780,"started[s]":1616747606,"ended[s]":0,"started":"2021-03-26 08:33:26.000","ended":"0","reason":0,"timeQ":0,"RFID tag":"0000000000000000","RFID class":"f4d82c69000000000000","Serial":"20296767","Sec":1466411}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.sessionid with value:9
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.eStart with value:65500.1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.ePres with value:1378
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.started_s with value:1616747606
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.ended_s with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.started with value:2021-03-26 08:33:26.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.ended with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.reason with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.timeQ with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.rfid_class with value:f4d82c69000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_00.sec with value:1466411
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.json with value:[{"ID":"101","Session ID":8,"Curr HW":20000,"E start":504454,"E pres":150547,"started[s]":1616672249,"ended[s]":1616683611,"started":"2021-03-25 11:37:29.000","ended":"2021-03-25 14:46:51.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"9b07e84a000000000000","Serial":"20296767","Sec":1466411}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.sessionid with value:8
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.eStart with value:50445.4
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.ePres with value:15054.7
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.started_s with value:1616672249
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.ended_s with value:1616683611
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.started with value:2021-03-25 11:37:29.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.ended with value:2021-03-25 14:46:51.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.reason with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.rfid_class with value:9b07e84a000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_01.sec with value:1466411
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.json with value:[{"ID":"102","Session ID":7,"Curr HW":20000,"E start":322901,"E pres":181553,"started[s]":1616164422,"ended[s]":1616175449,"started":"2021-03-19 14:33:42.000","ended":"2021-03-19 17:37:29.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"fe1e8b2b000000000000","Serial":"20296767","Sec":1466411}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.sessionid with value:7
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.eStart with value:32290.1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.ePres with value:18155.3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.started_s with value:1616164422
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.ended_s with value:1616175449
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.started with value:2021-03-19 14:33:42.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.ended with value:2021-03-19 17:37:29.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.reason with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.rfid_class with value:fe1e8b2b000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_02.sec with value:1466411
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.json with value:[{"ID":"103","Session ID":6,"Curr HW":20000,"E start":222666,"E pres":100235,"started[s]":1615638239,"ended[s]":1615648318,"started":"2021-03-13 12:23:59.000","ended":"2021-03-13 15:11:58.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"76e4d316000000000000","Serial":"20296767","Sec":1466412}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.sessionid with value:6
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.eStart with value:22266.6
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.ePres with value:10023.5
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.started_s with value:1615638239
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.ended_s with value:1615648318
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.started with value:2021-03-13 12:23:59.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.ended with value:2021-03-13 15:11:58.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.reason with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.rfid_class with value:76e4d316000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_03.sec with value:1466412
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.json with value:[{"ID":"104","Session ID":5,"Curr HW":20000,"E start":181890,"E pres":40776,"started[s]":1615290689,"ended[s]":1615294745,"started":"2021-03-09 11:51:29.000","ended":"2021-03-09 12:59:05.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"76e4d316000000000000","Serial":"20296767","Sec":1466412}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.sessionid with value:5
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.eStart with value:18189
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.ePres with value:4077.6
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.started_s with value:1615290689
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.ended_s with value:1615294745
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.started with value:2021-03-09 11:51:29.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.ended with value:2021-03-09 12:59:05.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.reason with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.rfid_class with value:76e4d316000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_04.sec with value:1466412
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.json with value:[{"ID":"105","Session ID":4,"Curr HW":20000,"E start":133509,"E pres":48381,"started[s]":1615207786,"ended[s]":1615212627,"started":"2021-03-08 12:49:46.000","ended":"2021-03-08 14:10:27.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"b9ca830c000000000000","Serial":"20296767","Sec":1466412}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.sessionid with value:4
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.eStart with value:13350.9
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.ePres with value:4838.1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.started_s with value:1615207786
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.ended_s with value:1615212627
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.started with value:2021-03-08 12:49:46.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.ended with value:2021-03-08 14:10:27.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.reason with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.rfid_class with value:b9ca830c000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_05.sec with value:1466412
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.json with value:[{"ID":"106","Session ID":3,"Curr HW":20000,"E start":32654,"E pres":100855,"started[s]":1615117666,"ended[s]":1615127564,"started":"2021-03-07 11:47:46.000","ended":"2021-03-07 14:32:44.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"82c4800c000000000000","Serial":"20296767","Sec":1466413}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.sessionid with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.eStart with value:3265.4
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.ePres with value:10085.5
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.started_s with value:1615117666
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.ended_s with value:1615127564
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.started with value:2021-03-07 11:47:46.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.ended with value:2021-03-07 14:32:44.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.reason with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.rfid_class with value:82c4800c000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_06.sec with value:1466413
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.json with value:[{"ID":"107","Session ID":2,"Curr HW":20000,"E start":32654,"E pres":0,"started[s]":1615117466,"ended[s]":1615117659,"started":"2021-03-07 11:44:26.000","ended":"2021-03-07 11:47:39.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"fdfe073f000000000000","Serial":"20296767","Sec":1466413}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.sessionid with value:2
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.eStart with value:3265.4
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.ePres with value:0
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.started_s with value:1615117466
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.ended_s with value:1615117659
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.started with value:2021-03-07 11:44:26.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.ended with value:2021-03-07 11:47:39.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.reason with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.rfid_class with value:fdfe073f000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_07.sec with value:1466413
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.json with value:[{"ID":"108","Session ID":1,"Curr HW":20000,"E start":2269,"E pres":30385,"started[s]":1613817709,"ended[s]":1613818767,"started":"2021-02-20 10:41:49.000","ended":"2021-02-20 10:59:27.000","reason":1,"timeQ":3,"RFID tag":"0000000000000000","RFID class":"fdfe073f000000000000","Serial":"20296767","Sec":1466413}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.sessionid with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.currentHardware with value:20000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.eStart with value:226.9
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.ePres with value:3038.5
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.started_s with value:1613817709
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.ended_s with value:1613818767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.started with value:2021-02-20 10:41:49.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.ended with value:2021-02-20 10:59:27.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.reason with value:1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.timeQ with value:3
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.rfid_class with value:fdfe073f000000000000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_08.sec with value:1466413
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.json with value:[{"ID":"109","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466414}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.sessionid with value:-1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.currentHardware with value:-1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.eStart with value:-0.1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.ePres with value:-0.1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.started_s with value:-1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.ended_s with value:-1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.reason with value:255
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.timeQ with value:255
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_09.sec with value:1466414
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.json with value:[{"ID":"110","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466414}]
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.sessionid with value:-1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.currentHardware with value:-1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.eStart with value:-0.1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.ePres with value:-0.1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.started_s with value:-1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.ended_s with value:-1
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.reason with value:255
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.timeQ with value:255
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.serial with value:20296767
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_10.sec with value:1466414
2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.json with value:[{"ID":"111","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466414}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_11.sec with value:1466414
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.json with value:[{"ID":"112","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466414}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_12.sec with value:1466414
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.json with value:[{"ID":"113","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466385}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_13.sec with value:1466385
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.json with value:[{"ID":"114","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466385}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_14.sec with value:1466385
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.json with value:[{"ID":"115","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466385}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_15.sec with value:1466385
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.json with value:[{"ID":"116","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466386}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_16.sec with value:1466386
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.json with value:[{"ID":"117","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466386}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_17.sec with value:1466386
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.json with value:[{"ID":"118","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466386}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_18.sec with value:1466386
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.json with value:[{"ID":"119","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466387}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_19.sec with value:1466387
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.json with value:[{"ID":"120","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466387}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_20.sec with value:1466387
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.json with value:[{"ID":"121","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466387}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_21.sec with value:1466387
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.json with value:[{"ID":"122","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466388}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_22.sec with value:1466388
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.json with value:[{"ID":"123","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466388}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_23.sec with value:1466388
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.json with value:[{"ID":"124","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466388}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_24.sec with value:1466388
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.json with value:[{"ID":"125","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466389}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_25.sec with value:1466389
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.json with value:[{"ID":"126","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466389}]
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.sessionid with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.currentHardware with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.eStart with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.ePres with value:-0.1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.started_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.ended_s with value:-1
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.reason with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.timeQ with value:255
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.serial with value:20296767
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_26.sec with value:1466389
2021-03-26 09:49:45.748  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.json with value:[{"ID":"127","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466389}]
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.sessionid with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.currentHardware with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.eStart with value:-0.1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.ePres with value:-0.1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.started_s with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.ended_s with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.reason with value:255
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.timeQ with value:255
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.serial with value:20296767
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_27.sec with value:1466389
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.json with value:[{"ID":"128","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466389}]
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.sessionid with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.currentHardware with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.eStart with value:-0.1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.ePres with value:-0.1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.started_s with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.ended_s with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.reason with value:255
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.timeQ with value:255
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.serial with value:20296767
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_28.sec with value:1466389
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.json with value:[{"ID":"129","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466390}]
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.sessionid with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.currentHardware with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.eStart with value:-0.1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.ePres with value:-0.1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.started_s with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.ended_s with value:-1
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.started with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.ended with value:2106-02-07 06:28:15.000
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.reason with value:255
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.timeQ with value:255
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.rfid_class with value:ffffffffffffffffffff
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.serial with value:20296767
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_29.sec with value:1466390
2021-03-26 09:49:45.764  - debug: kecontact.0 (2236) update state kecontact.0.Sessions.Session_30.json with value:[{"ID":"130","Session ID":-1,"Curr HW":-1,"E start":-1,"E pres":-1,"started[s]":-1,"ended[s]":-1,"started":"2106-02-07 06:28:15.000","ended":"2106-02-07 06:28:15.000","reason":255,"timeQ":255,"RFID tag":"ffffffffffffffff","RFID class":"ffffffffffffffffffff","Serial":"20296767","Sec":1466390}]

[Sneak-L8]

@qlink Leider hat es den Spoiler etwas durcheinander gebracht. Man muss ihn zigmal öffnen. Evlt. liegt es dara, dass der Output nicht mit "Code" markiert ist. Kannst Du das ändern? Dann kann ich ihn mir ansehen ohne erst 100 mal klicken zu müssen.

[Qlink]

@sneak-l8

habs grad aktualisiert mit code tag ...

[Sneak-L8]

@qlink So, hab's gerade entdeckt. Ganz trivial...

2021-03-26 09:49:45.733  - debug: kecontact.0 (2236) update state kecontact.0.display with value:volle Ladeleistung

Du hast den state kecontact.0.automatic.photovoltaics auf false sitzen, dann liefert die Wallbox immer die volle Leistung. Diesen Schalter auf true setzen und schon sollte es funktionieren.
Um den Zustand leicht zu erkennen, wird der Zustand auch immer am Wallbox-Display angezeigt.

Bei der Gelegenheit habe ich (für eine künftige Version) den Default-Wert auf Automatik = an gestellt.

[Qlink]

@sneak-l8

Vielen Dank für deine Hilfe.
Das war die Ursache!
Jetzt funktionierts genau wie eingestellt.

Genialer Adapter!

Beste Grüße

[Qlink]

@Sneak-L8

Hab mich doch wohl etwas zu früh gefreut, oder verstehe ich die Settings eventuell wieder falsch.

Ich habe bei Mindestladezeit 7200s eingestellt.
Sollte er dann nicht, egal wie die aktuelle PV Situation aussieht, auf jeden Fall mal 2h laden... ?

Ich hab gerade angesteckt und er stoppt von selbst nach kurzer Zeit den Ladevorgang, weil Ladeunterschreitung ...

kecontact.0	2021-03-29 13:59:08.892	info	(4876) stop charging
kecontact.0	2021-03-29 13:58:38.876	info	(4876) dynamic adaption of charging to 6000 mA
kecontact.0	2021-03-29 13:53:08.772	info	(4876) stop charging
kecontact.0	2021-03-29 13:52:38.763	info	(4876) dynamic adaption of charging to 8500 mA
kecontact.0	2021-03-29 13:52:08.762	info	(4876) dynamic adaption of charging to 7000 mA
kecontact.0	2021-03-29 13:51:38.749	info	(4876) stop charging
kecontact.0	2021-03-29 13:50:38.730	info	(4876) dynamic adaption of charging to 6500 mA
kecontact.0	2021-03-29 13:50:08.720	info	(4876) dynamic adaption of charging to 6000 mA
kecontact.0	2021-03-29 13:49:38.711	info	(4876) dynamic adaption of charging to 7000 mA
kecontact.0	2021-03-29 13:48:38.694	info	(4876) dynamic adaption of charging to 6500 mA
kecontact.0	2021-03-29 13:48:08.683	info	(4876) dynamic adaption of charging to 6000 mA
kecontact.0	2021-03-29 13:47:38.670	info	(4876) dynamic adaption of charging to 7500 mA
kecontact.0	2021-03-29 13:47:08.662	info	(4876) dynamic adaption of charging to 7000 mA
kecontact.0	2021-03-29 13:46:38.654	info	(4876) dynamic adaption of charging to 6500 mA
kecontact.0	2021-03-29 13:46:08.649	info	(4876) dynamic adaption of charging to 6000 mA
kecontact.0	2021-03-29 13:45:38.640	info	(4876) dynamic adaption of charging to 6500 mA
kecontact.0	2021-03-29 13:45:08.626	info	(4876) dynamic adaption of charging to 7000 mA
kecontact.0	2021-03-29 13:44:38.613	info	(4876) dynamic adaption of charging to 8000 mA
kecontact.0	2021-03-29 13:44:08.596	info	(4876) dynamic adaption of charging to 7500 mA
kecontact.0	2021-03-29 13:43:38.590	info	(4876) stop charging
kecontact.0	2021-03-29 13:42:38.576	info	(4876) stop charging
kecontact.0	2021-03-29 13:42:08.573	info	(4876) dynamic adaption of charging to 8500 mA
kecontact.0	2021-03-29 13:41:38.564	info	(4876) stop charging
kecontact.0	2021-03-29 13:41:08.551	info	(4876) dynamic adaption of charging to 9500 mA
kecontact.0	2021-03-29 13:40:38.542	info	(4876) stop charging
kecontact.0	2021-03-29 13:40:03.020	info	(4876) dynamic adaption of charging to 8500 mA
kecontact.0	2021-03-29 13:40:03.020	info	(4876) vehicle plugged to wallbox

[Sneak-L8]

@qlink was mich wundert, ist dass bei Dir der Logeintrag "vehicle (re)starts to charge" fehlt. So sieht es bei mir aus:

kecontact.0	2021-03-29 13:31:07.605	info	(11211) dynamic adaption of charging to 9500 mA
kecontact.0	2021-03-29 13:30:37.603	info	(11211) dynamic adaption of charging to 11500 mA
kecontact.0	2021-03-29 13:29:07.600	info	(11211) vehicle (re)starts to charge
kecontact.0	2021-03-29 13:29:07.599	info	(11211) dynamic adaption of charging to 8500 mA
kecontact.0	2021-03-29 13:28:37.596	info	(11211) dynamic adaption of charging to 7500 mA
kecontact.0	2021-03-29 13:28:37.587	info	(11211) vehicle plugged to wallbox

Dadurch wird der Startzeitpunkt fürs Laden nicht initialisiert und liegt weit in der Vergangenheit. Dann sind die 7200 Sekunden immer schon um. Findest Du in einem älteren Log den Eintrag, dass das Laden gestartet wurde? Musst ggfs. auch die Tage davor anschauen. Ist da dann was Auffäligen drumherum zu sehen?

[Qlink]

@sneak-l8 said in Sammlung Informationen Wallbox & ioBroker-Integration:

(re)starts

Hab den Eintrag im Log vor 3 Tagen gefunden:

2021-03-26 09:33:36.970  - info: kecontact.0 (1804) vehicle plugged to wallbox
2021-03-26 09:34:08.222  - info: kecontact.0 (1804) vehicle (re)starts to charge
2021-03-26 09:39:11.134  - info: host.iob01 stopInstance system.adapter.kecontact.0 (force=false, process=true)
2021-03-26 09:39:11.135  - info: kecontact.0 (1804) Got terminate signal TERMINATE_YOURSELF
2021-03-26 09:39:11.135  - info: kecontact.0 (1804) terminating
2021-03-26 09:39:11.135  - info: kecontact.0 (1804) Terminated (ADAPTER_REQUESTED_TERMINATION): Without reason
2021-03-26 09:39:11.134  - info: host.iob01 stopInstance system.adapter.kecontact.0 send kill signal
2021-03-26 09:39:11.810  - info: host.iob01 instance system.adapter.kecontact.0 terminated with code 11 (ADAPTER_REQUESTED_TERMINATION)
2021-03-26 09:39:14.172  - info: host.iob01 instance system.adapter.kecontact.0 started with pid 10068
2021-03-26 09:39:15.174  - info: kecontact.0 (10068) starting. Version 1.1.1 in C:/iobroker/iob01/node_modules/iobroker.kecontact, node: v10.17.0, js-controller: 3.2.16
2021-03-26 09:39:20.206  - info: kecontact.0 (10068) starting charging station in active mode
2021-03-26 09:39:20.206  - info: kecontact.0 (10068) minimum amperage not speficied or too low, using default value of 6000
2021-03-26 09:44:52.430  - info: host.iob01 stopInstance system.adapter.kecontact.0 (force=false, process=true)
2021-03-26 09:44:52.431  - info: kecontact.0 (10068) Got terminate signal TERMINATE_YOURSELF
2021-03-26 09:44:52.431  - info: kecontact.0 (10068) terminating
2021-03-26 09:44:52.431  - info: kecontact.0 (10068) Terminated (ADAPTER_REQUESTED_TERMINATION): Without reason
2021-03-26 09:44:52.430  - info: host.iob01 stopInstance system.adapter.kecontact.0 send kill signal
2021-03-26 09:44:53.086  - info: host.iob01 instance system.adapter.kecontact.0 terminated with code 11 (ADAPTER_REQUESTED_TERMINATION)
2021-03-26 09:44:55.459  - info: host.iob01 instance system.adapter.kecontact.0 started with pid 1448
2021-03-26 09:44:56.117  - debug: kecontact.0 (1448) Redis Objects: Use Redis connection: 127.0.0.1:9001
2021-03-26 09:44:56.133  - debug: kecontact.0 (1448) Objects client ready ... initialize now
2021-03-26 09:44:56.148  - debug: kecontact.0 (1448) Objects create System PubSub Client
2021-03-26 09:44:56.148  - debug: kecontact.0 (1448) Objects create User PubSub Client
2021-03-26 09:44:56.148  - debug: kecontact.0 (1448) Objects client initialize lua scripts
2021-03-26 09:44:56.164  - debug: kecontact.0 (1448) Objects connected to redis: 127.0.0.1:9001
2021-03-26 09:44:56.164  - debug: kecontact.0 (1448) objectDB connected
2021-03-26 09:44:56.164  - debug: kecontact.0 (1448) Redis States: Use Redis connection: 127.0.0.1:9000
2021-03-26 09:44:56.179  - debug: kecontact.0 (1448) States create System PubSub Client
2021-03-26 09:44:56.179  - debug: kecontact.0 (1448) States create User PubSub Client
2021-03-26 09:44:56.179  - debug: kecontact.0 (1448) States connected to redis: 127.0.0.1:9000
2021-03-26 09:44:56.179  - debug: kecontact.0 (1448) statesDB connected
2021-03-26 09:44:56.367  - info: kecontact.0 (1448) starting. Version 1.1.1 in C:/iobroker/iob01/node_modules/iobroker.kecontact, node: v10.17.0, js-controller: 3.2.16