NODEmcu K-Type Temp-Fühler in IObroker !? [gelöst]
-
@qax1 Hast du jetzt meine MQTT genutzt? Und hast du das Semikolon entfernt?
Hier darf nur die IP stehen:
Also http:// weg -
@qax1 Dann entpack jetzt die Datei MQTT.7z und schieb den Ordner MQTT dann in Dokumente/Arduino.
Und danach oben wieder auf MQTT.h ändern.@mcu
Ok... erledigt... jetzt kommt :Arduino: 1.8.13 (Windows 10), Board: "NodeMCU 1.0 (ESP-12E Module), 80 MHz, Flash, Legacy (new can return nullptr), All SSL ciphers (most compatible), 4MB (FS:2MB OTA:~1019KB), 2, v2 Lower Memory, Disabled, WIFI, Only Sketch, 115200"
C:\Users\Stefan\Documents\Arduino\MQTT-TEST-1\MQTT-TEST-1.ino: In function 'void connect()':
MQTT-TEST-1:40:35: error: invalid operands of types 'const char [10]' and 'const char [3]' to binary 'operator+'
client.subscribe(client_name + "/+"); ^MQTT-TEST-1:41:33: error: invalid operands of types 'const char [10]' and 'const char [7]' to binary 'operator+'
client.publish(client_name + "/alive","true"); ^C:\Users\Stefan\Documents\Arduino\MQTT-TEST-1\MQTT-TEST-1.ino: In function 'void loop()':
MQTT-TEST-1:75:34: error: invalid operands of types 'const char [10]' and 'const char [14]' to binary 'operator+'
client.publish(client_name + "/InternalTemp",String(c)); ^MQTT-TEST-1:81:6: error: 'werteCount' was not declared in this scope
werteCount = 0; ^MQTT-TEST-1:86:35: error: invalid operands of types 'const char [10]' and 'const char [16]' to binary 'operator+'
client.publish(client_name + "/connectProblem","Verbindungsproblem gehabt"); ^exit status 1
invalid operands of types 'const char [10]' and 'const char [3]' to binary 'operator+'
Dieser Bericht wäre detaillierter, wenn die Option
"Ausführliche Ausgabe während der Kompilierung"
in Datei -> Voreinstellungen aktiviert wäre. -
@mcu
Ok... erledigt... jetzt kommt :Arduino: 1.8.13 (Windows 10), Board: "NodeMCU 1.0 (ESP-12E Module), 80 MHz, Flash, Legacy (new can return nullptr), All SSL ciphers (most compatible), 4MB (FS:2MB OTA:~1019KB), 2, v2 Lower Memory, Disabled, WIFI, Only Sketch, 115200"
C:\Users\Stefan\Documents\Arduino\MQTT-TEST-1\MQTT-TEST-1.ino: In function 'void connect()':
MQTT-TEST-1:40:35: error: invalid operands of types 'const char [10]' and 'const char [3]' to binary 'operator+'
client.subscribe(client_name + "/+"); ^MQTT-TEST-1:41:33: error: invalid operands of types 'const char [10]' and 'const char [7]' to binary 'operator+'
client.publish(client_name + "/alive","true"); ^C:\Users\Stefan\Documents\Arduino\MQTT-TEST-1\MQTT-TEST-1.ino: In function 'void loop()':
MQTT-TEST-1:75:34: error: invalid operands of types 'const char [10]' and 'const char [14]' to binary 'operator+'
client.publish(client_name + "/InternalTemp",String(c)); ^MQTT-TEST-1:81:6: error: 'werteCount' was not declared in this scope
werteCount = 0; ^MQTT-TEST-1:86:35: error: invalid operands of types 'const char [10]' and 'const char [16]' to binary 'operator+'
client.publish(client_name + "/connectProblem","Verbindungsproblem gehabt"); ^exit status 1
invalid operands of types 'const char [10]' and 'const char [3]' to binary 'operator+'
Dieser Bericht wäre detaillierter, wenn die Option
"Ausführliche Ausgabe während der Kompilierung"
in Datei -> Voreinstellungen aktiviert wäre. -
Ich weiß nicht ob s was zu sagen hat,
aber ich habe in IObroker im MQTT-Adapter
keinen Namen / Passwort vergeben.@mcu Eins nachdem anderen:
- String MCUName = "SensorMax"; einfügen nach #define client_name
- werteCount = 0; Zeile komplett löschen
- bei client.subscribe(client_name : client_name durch MCUName ersetzen
- und bei allen client.publish(client_name : client_name durch MCUName ersetzen
- beim client.connect"MQTTUser","MQTTPassword" -> "",""
-
@mcu Eins nachdem anderen:
- String MCUName = "SensorMax"; einfügen nach #define client_name
- werteCount = 0; Zeile komplett löschen
- bei client.subscribe(client_name : client_name durch MCUName ersetzen
- und bei allen client.publish(client_name : client_name durch MCUName ersetzen
- beim client.connect"MQTTUser","MQTTPassword" -> "",""
-
@mcu ```
#include <Wire.h>
#include <SPI.h>
#include "Adafruit_MAX31855.h"
#include <ESP8266WiFi.h>#include <MQTT.h>
#define CLK 14 //connect CLK to GPIO14
#define CS 5 //connect CS to GPIO5
#define DO 12 //connect DO to GPIO12#define client_name "SensorMAX"
String MCUName = "SensorMax";const char ssid[] = "xyz";
const char pass[] = "xxxxxxxxxxxxxxxxx";
String Nachricht_MQTT = "";
String Topic_MQTT = "";Adafruit_MAX31855 thermocouple(CLK,CS,DO);
WiFiClient net;
MQTTClient client;void connect() {
Serial.print("\nchecking wifi...");
while (WiFi.status() != WL_CONNECTED) {
Serial.print(".");
delay(1000);
}
Serial.print("\nconnecting...");
while (!client.connect(client_name,"MQTTUser","MQTTPassword")) {
Serial.print(".");
delay(1000);
}
Serial.print("\nconnected!");client.subscribe(MCUName + "/+");
client.publish(MCUName + "/alive","true");}
void messageReceived(String &topic, String &payload) {
Serial.println("MQTT incoming: " + topic + " - " + payload);
Topic_MQTT = topic;
Nachricht_MQTT = payload;topic = "";
payload = "";
}void setup() {
Serial.begin(9600);
Serial.println("MAX31855 testing");
delay(500);
WiFi.begin(ssid, pass);
client.begin("192.168.178.30",1883,net); //192.168.178.45
connect(); //alive wird gesendet
client.onMessage(messageReceived);}
void loop() {
Serial.print("Internal Temp = ");
Serial.println(thermocouple.readInternal());
delay(100);
double c = thermocouple.readCelsius();
if (isnan(c)) {
Serial.println("Something wrong with thermocouple!");
} else {
Serial.print("C = ");
Serial.println(c);
client.publish(MCUName + "/InternalTemp",String(c));
}
client.loop();
if (!client.connected()) {
Serial.println("Neustart!");
delay(200);
WiFi.begin(ssid, pass);
client.begin("http://192.168.178.30",1883,net);
connect(); //alive wird gesendet
client.onMessage(messageReceived);
client.publish(MCUName + "/connectProblem","Verbindungsproblem gehabt");
}
delay(1000);
} -
@mcu ```
#include <Wire.h>
#include <SPI.h>
#include "Adafruit_MAX31855.h"
#include <ESP8266WiFi.h>#include <MQTT.h>
#define CLK 14 //connect CLK to GPIO14
#define CS 5 //connect CS to GPIO5
#define DO 12 //connect DO to GPIO12#define client_name "SensorMAX"
String MCUName = "SensorMax";const char ssid[] = "xyz";
const char pass[] = "xxxxxxxxxxxxxxxxx";
String Nachricht_MQTT = "";
String Topic_MQTT = "";Adafruit_MAX31855 thermocouple(CLK,CS,DO);
WiFiClient net;
MQTTClient client;void connect() {
Serial.print("\nchecking wifi...");
while (WiFi.status() != WL_CONNECTED) {
Serial.print(".");
delay(1000);
}
Serial.print("\nconnecting...");
while (!client.connect(client_name,"MQTTUser","MQTTPassword")) {
Serial.print(".");
delay(1000);
}
Serial.print("\nconnected!");client.subscribe(MCUName + "/+");
client.publish(MCUName + "/alive","true");}
void messageReceived(String &topic, String &payload) {
Serial.println("MQTT incoming: " + topic + " - " + payload);
Topic_MQTT = topic;
Nachricht_MQTT = payload;topic = "";
payload = "";
}void setup() {
Serial.begin(9600);
Serial.println("MAX31855 testing");
delay(500);
WiFi.begin(ssid, pass);
client.begin("192.168.178.30",1883,net); //192.168.178.45
connect(); //alive wird gesendet
client.onMessage(messageReceived);}
void loop() {
Serial.print("Internal Temp = ");
Serial.println(thermocouple.readInternal());
delay(100);
double c = thermocouple.readCelsius();
if (isnan(c)) {
Serial.println("Something wrong with thermocouple!");
} else {
Serial.print("C = ");
Serial.println(c);
client.publish(MCUName + "/InternalTemp",String(c));
}
client.loop();
if (!client.connected()) {
Serial.println("Neustart!");
delay(200);
WiFi.begin(ssid, pass);
client.begin("http://192.168.178.30",1883,net);
connect(); //alive wird gesendet
client.onMessage(messageReceived);
client.publish(MCUName + "/connectProblem","Verbindungsproblem gehabt");
}
delay(1000);
}@qax1 sagte in NODEmcu K-Type Temp-Fühler in IObroker !?:
Serial.print("\nconnecting...");
while (!client.connect(client_name,"MQTTUser","MQTTPassword")) {Serial.print("\nconnecting..."); while (!client.connect(client_name,"MQTTUser","MQTTPassword")) {noch ändern -> "",""
Code-tags - erste Zeile frei lassen , sonst versteht er das nicht.
client.begin("http://192.168.178.30",1883,net); ->client.begin("192.168.178.30",1883,net);
das http:// entfernen -
@qax1 sagte in NODEmcu K-Type Temp-Fühler in IObroker !?:
Serial.print("\nconnecting...");
while (!client.connect(client_name,"MQTTUser","MQTTPassword")) {Serial.print("\nconnecting..."); while (!client.connect(client_name,"MQTTUser","MQTTPassword")) {noch ändern -> "",""
Code-tags - erste Zeile frei lassen , sonst versteht er das nicht.
client.begin("http://192.168.178.30",1883,net); ->client.begin("192.168.178.30",1883,net);
das http:// entfernen -
#include <Wire.h> #include <SPI.h> #include "Adafruit_MAX31855.h" #include <ESP8266WiFi.h> #include <MQTT.h> #define CLK 14 //connect CLK to GPIO14 #define CS 5 //connect CS to GPIO5 #define DO 12 //connect DO to GPIO12 #define client_name "SensorMAX" String MCUName = "SensorMax"; const char ssid[] = "xyz"; const char pass[] = "xxxxxxxxxxxxxxxxxxx"; String Nachricht_MQTT = ""; String Topic_MQTT = ""; Adafruit_MAX31855 thermocouple(CLK,CS,DO); WiFiClient net; MQTTClient client; void connect() { Serial.print("\nchecking wifi..."); while (WiFi.status() != WL_CONNECTED) { Serial.print("."); delay(1000); } Serial.print("\nconnecting..."); while (!client.connect(client_name,"MQTTUser","MQTTPassword")) { Serial.print("."); delay(1000); } Serial.print("\nconnected!"); client.subscribe(MCUName + "/+"); client.publish(MCUName + "/alive","true"); } void messageReceived(String &topic, String &payload) { Serial.println("MQTT incoming: " + topic + " - " + payload); Topic_MQTT = topic; Nachricht_MQTT = payload; topic = ""; payload = ""; } void setup() { Serial.begin(9600); Serial.println("MAX31855 testing"); delay(500); WiFi.begin(ssid, pass); client.begin("192.168.178.30",1883,net); //192.168.178.45 connect(); //alive wird gesendet client.onMessage(messageReceived); } void loop() { Serial.print("Internal Temp = "); Serial.println(thermocouple.readInternal()); delay(100); double c = thermocouple.readCelsius(); if (isnan(c)) { Serial.println("Something wrong with thermocouple!"); } else { Serial.print("C = "); Serial.println(c); client.publish(MCUName + "/InternalTemp",String(c)); } client.loop(); if (!client.connected()) { Serial.println("Neustart!"); delay(200); WiFi.begin(ssid, pass); client.begin("192.168.178.30",1883,net); connect(); //alive wird gesendet client.onMessage(messageReceived); client.publish(MCUName + "/connectProblem","Verbindungsproblem gehabt"); } delay(1000); } -
#include <Wire.h> #include <SPI.h> #include "Adafruit_MAX31855.h" #include <ESP8266WiFi.h> #include <MQTT.h> #define CLK 14 //connect CLK to GPIO14 #define CS 5 //connect CS to GPIO5 #define DO 12 //connect DO to GPIO12 #define client_name "SensorMAX" String MCUName = "SensorMax"; const char ssid[] = "xyz"; const char pass[] = "xxxxxxxxxxxxxxxxxxx"; String Nachricht_MQTT = ""; String Topic_MQTT = ""; Adafruit_MAX31855 thermocouple(CLK,CS,DO); WiFiClient net; MQTTClient client; void connect() { Serial.print("\nchecking wifi..."); while (WiFi.status() != WL_CONNECTED) { Serial.print("."); delay(1000); } Serial.print("\nconnecting..."); while (!client.connect(client_name,"MQTTUser","MQTTPassword")) { Serial.print("."); delay(1000); } Serial.print("\nconnected!"); client.subscribe(MCUName + "/+"); client.publish(MCUName + "/alive","true"); } void messageReceived(String &topic, String &payload) { Serial.println("MQTT incoming: " + topic + " - " + payload); Topic_MQTT = topic; Nachricht_MQTT = payload; topic = ""; payload = ""; } void setup() { Serial.begin(9600); Serial.println("MAX31855 testing"); delay(500); WiFi.begin(ssid, pass); client.begin("192.168.178.30",1883,net); //192.168.178.45 connect(); //alive wird gesendet client.onMessage(messageReceived); } void loop() { Serial.print("Internal Temp = "); Serial.println(thermocouple.readInternal()); delay(100); double c = thermocouple.readCelsius(); if (isnan(c)) { Serial.println("Something wrong with thermocouple!"); } else { Serial.print("C = "); Serial.println(c); client.publish(MCUName + "/InternalTemp",String(c)); } client.loop(); if (!client.connected()) { Serial.println("Neustart!"); delay(200); WiFi.begin(ssid, pass); client.begin("192.168.178.30",1883,net); connect(); //alive wird gesendet client.onMessage(messageReceived); client.publish(MCUName + "/connectProblem","Verbindungsproblem gehabt"); } delay(1000); }@qax1 sagte in NODEmcu K-Type Temp-Fühler in IObroker !?:
while (!client.connect(client_name,"MQTTUser","MQTTPassword"))
Immer noch nicht geändert:
while (!client.connect(client_name,"MQTTUser","MQTTPassword")) -> while (!client.connect(client_name,"","")) -
@qax1 sagte in NODEmcu K-Type Temp-Fühler in IObroker !?:
while (!client.connect(client_name,"MQTTUser","MQTTPassword"))
Immer noch nicht geändert:
while (!client.connect(client_name,"MQTTUser","MQTTPassword")) -> while (!client.connect(client_name,"","")) -
@mcu sagte in NODEmcu K-Type Temp-Fühler in IObroker !?:
while (!client.connect(client_name,"",""))
Serial.print("\nconnecting..."); while (!client.connect(MCUName,"","")) { Serial.print("."); delay(1000);so ?
-
@qax1
while (!client.connect(MCUName,"","")) {
dort nicht den client_name ersetzen!while (!client.connect(client_name,"",""))
-
Serial.print("\nconnecting..."); while (!client.connect(client_name,"","")) { Serial.print("."); delay(1000);ok
-
@qax1 Dann lass mal laufen. Kommt im ioBroker MQTT was an?
Sonst zeige die Einstellungen zum MQTT-Adapter.
Meine sind:
-
Sau Geil es läuft....
Ich kann dir gar nicht genug Danken....
Das hätte ich alleine wohl nie hinbekommen
Hey! Du scheinst an dieser Unterhaltung interessiert zu sein, hast aber noch kein Konto.
Hast du es satt, bei jedem Besuch durch die gleichen Beiträge zu scrollen? Wenn du dich für ein Konto anmeldest, kommst du immer genau dorthin zurück, wo du zuvor warst, und kannst dich über neue Antworten benachrichtigen lassen (entweder per E-Mail oder Push-Benachrichtigung). Du kannst auch Lesezeichen speichern und Beiträge positiv bewerten, um anderen Community-Mitgliedern deine Wertschätzung zu zeigen.
Mit deinem Input könnte dieser Beitrag noch besser werden 💗
Registrieren Anmelden556
Online32.9k
Benutzer83.0k
Themen1.3m
Beiträge