Probleme mit Serialport bei zwave2
-
@Esmax666 schau auch mal ob in
/boot/config.txteine Zeileenable_uart=1zu finden ist.
Auf meinem Pi4 ist das der Fall und dort geht der Adapter. -
pi@raspberrypi:/opt/iobroker/node_modules/iobroker.zwave2 $ sudo lsof /dev/ttyACM0 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME node 673 iobroker 26uW CHR 166,0 0t0 427 /dev/ttyACM0 -
@alcalzone said in Probleme mit Serialport bei zwave2:
config.txt
ganz am ende
pi@raspberrypi:/boot $ cat config.txt # For more options and information see # http://rpf.io/configtxt # Some settings may impact device functionality. See link above for details # uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 # uncomment this if your display has a black border of unused pixels visible # and your display can output without overscan #disable_overscan=1 # uncomment the following to adjust overscan. Use positive numbers if console # goes off screen, and negative if there is too much border #overscan_left=16 #overscan_right=16 #overscan_top=16 #overscan_bottom=16 # uncomment to force a console size. By default it will be display's size minus # overscan. #framebuffer_width=1280 #framebuffer_height=720 # uncomment if hdmi display is not detected and composite is being output #hdmi_force_hotplug=1 # uncomment to force a specific HDMI mode (this will force VGA) #hdmi_group=1 #hdmi_mode=1 # uncomment to force a HDMI mode rather than DVI. This can make audio work in # DMT (computer monitor) modes #hdmi_drive=2 # uncomment to increase signal to HDMI, if you have interference, blanking, or # no display #config_hdmi_boost=4 # uncomment for composite PAL #sdtv_mode=2 #uncomment to overclock the arm. 700 MHz is the default. #arm_freq=800 # Uncomment some or all of these to enable the optional hardware interfaces #dtparam=i2c_arm=on #dtparam=i2s=on #dtparam=spi=on # Uncomment this to enable infrared communication. #dtoverlay=gpio-ir,gpio_pin=17 #dtoverlay=gpio-ir-tx,gpio_pin=18 # Additional overlays and parameters are documented /boot/overlays/README # Enable audio (loads snd_bcm2835) dtparam=audio=on [pi4] # Enable DRM VC4 V3D driver on top of the dispmanx display stack dtoverlay=vc4-fkms-v3d max_framebuffers=2 [all] #dtoverlay=vc4-fkms-v3d enable_uart=1 -
@alcalzone ist config.txt ok ?
sonst bei starten habe ich grün und gekomme jetzt das
zwave2.0 2021-05-22 10:49:27.281 info (10672) Node 2 is alive zwave2.0 2021-05-22 10:49:27.257 debug (10672) object zwave2.0.Node_026.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{ zwave2.0 2021-05-22 10:49:27.247 info (10672) Node 2: ready to use zwave2.0 2021-05-22 10:49:27.075 info (10672) Node 25: ready to use zwave2.0 2021-05-22 10:49:27.048 info (10672) Node 24: ready to use zwave2.0 2021-05-22 10:49:26.970 info (10672) Node 23: ready to use zwave2.0 2021-05-22 10:49:26.782 debug (10672) object zwave2.0.Node_022.Multilevel_Switch.down changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Down)"},"native":{ zwave2.0 2021-05-22 10:49:26.639 debug (10672) object zwave2.0.Node_022.Multilevel_Switch.up changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Up)"},"native":{"nod zwave2.0 2021-05-22 10:49:26.520 info (10672) Node 20: ready to use zwave2.0 2021-05-22 10:49:26.454 info (10672) Node 9: ready to use zwave2.0 2021-05-22 10:49:26.412 info (10672) Node 8: ready to use zwave2.0 2021-05-22 10:49:26.382 info (10672) Node 7: ready to use zwave2.0 2021-05-22 10:49:25.971 info (10672) Node 1: ready to use zwave2.0 2021-05-22 10:49:25.717 info (10672) The driver is ready. Found 21 nodes. zwave2.0 2021-05-22 10:49:21.694 info (10672) starting. Version 1.9.3 in /opt/iobroker/node_modules/iobroker.zwave2, node: v12.22.1, js-controller: 3.2.16 zwave2.0 2021-05-22 10:49:21.461 debug (10672) statesDB connected zwave2.0 2021-05-22 10:49:21.460 debug (10672) States connected to redis: 127.0.0.1:9000 zwave2.0 2021-05-22 10:49:21.452 debug (10672) States create User PubSub Client zwave2.0 2021-05-22 10:49:21.451 debug (10672) States create System PubSub Client zwave2.0 2021-05-22 10:49:21.440 debug (10672) Redis States: Use Redis connection: 127.0.0.1:9000 zwave2.0 2021-05-22 10:49:21.437 debug (10672) objectDB connected zwave2.0 2021-05-22 10:49:21.285 debug (10672) Objects connected to redis: 127.0.0.1:9001 zwave2.0 2021-05-22 10:49:21.271 debug (10672) Objects client initialize lua scripts zwave2.0 2021-05-22 10:49:21.270 debug (10672) Objects create User PubSub Client zwave2.0 2021-05-22 10:49:21.268 debug (10672) Objects create System PubSub Client zwave2.0 2021-05-22 10:49:21.265 debug (10672) Objects client ready ... initialize now zwave2.0 2021-05-22 10:49:21.228 debug (10672) Redis Objects: Use Redis connection: 127.0.0.1:9001 host.raspberrypi 2021-05-22 10:49:19.250 info instance system.adapter.zwave2.0 started with pid 10672 host.raspberrypi 2021-05-22 10:49:19.081 info "system.adapter.zwave2.0" enabled host.raspberrypi 2021-05-22 10:48:42.831 info instance system.adapter.zwave2.0 terminated with code 11 (ADAPTER_REQUESTED_TERMINATION) zwave2.0 2021-05-22 10:48:42.176 info (673) Terminated (ADAPTER_REQUESTED_TERMINATION): Without reason zwave2.0 2021-05-22 10:48:42.175 info (673) terminating zwave2.0 2021-05-22 10:48:42.174 info (673) Cleaned everything up! zwave2.0 2021-05-22 10:48:42.006 info (673) Resetting node status... zwave2.0 2021-05-22 10:48:41.974 info (673) Shutting down driver... zwave2.0 2021-05-22 10:48:41.972 info (673) Got terminate signal TERMINATE_YOURSELF host.raspberrypi 2021-05-22 10:48:41.973 info stopInstance system.adapter.zwave2.0 send kill signal host.raspberrypi 2021-05-22 10:48:41.963 info stopInstance system.adapter.zwave2.0 (force=false, process=true) host.raspberrypi 2021-05-22 10:48:41.958 info "system.adapter.zwave2.0" disabledund in console bekomme ich das
pi@raspberrypi:~ $ ls -ls /dev/ | grep serial 0 drwxr-xr-x 4 root root 80 Mai 21 13:46 serial 0 lrwxrwxrwx 1 root root 5 Mai 20 20:56 serial0 -> ttyS0 0 lrwxrwxrwx 1 root root 7 Mai 20 20:56 serial1 -> ttyAMA0 pi@raspberrypi:~ $ cd /opt/iobroker/node_modules/iobroker.zwave2 pi@raspberrypi:/opt/iobroker/node_modules/iobroker.zwave2 $ node build/main.js --force --logs 2021-05-22 10:53:01.219 - error: zwave2.0 (26343) adapter disabled 2021-05-22 10:53:01.229 - info: zwave2.0 (26343) starting. Version 1.9.3 in /opt/iobroker/node_modules/iobroker.zwave2, node: v12.22.1, js-controller: 3.2.16 10:53:01.309 DRIVER ███████╗ ██╗ ██╗ █████╗ ██╗ ██╗ ███████╗ ██╗ ███████╗ ╚══███╔╝ ██║ ██║ ██╔══██╗ ██║ ██║ ██╔════╝ ██║ ██╔════╝ ███╔╝ ██║ █╗ ██║ ███████║ ██║ ██║ █████╗ █████╗ ██║ ███████╗ ███╔╝ ██║███╗██║ ██╔══██║ ╚██╗ ██╔╝ ██╔══╝ ╚════╝ ██ ██║ ╚════██║ ███████╗ ╚███╔███╔╝ ██║ ██║ ╚████╔╝ ███████╗ ╚█████╔╝ ███████║ ╚══════╝ ╚══╝╚══╝ ╚═╝ ╚═╝ ╚═══╝ ╚══════╝ ╚════╝ ╚══════╝ 10:53:01.314 DRIVER version 7.4.0 10:53:01.316 CONFIG version 7.4.0 10:53:01.317 DRIVER 10:53:01.318 DRIVER starting driver... 10:53:01.346 DRIVER opening serial port /dev/ttyACM0 10:53:01.366 DRIVER serial port opened 10:53:01.368 SERIAL » [NAK] (0x15) 10:53:02.875 DRIVER loading configuration... 10:53:04.042 DRIVER beginning interview... 10:53:04.044 DRIVER added request handler for AddNodeToNetwork (0x4a)... 1 registered 10:53:04.045 DRIVER added request handler for RemoveNodeFromNetwork (0x4b)... 1 registered 10:53:04.045 DRIVER added request handler for ReplaceFailedNode (0x63)... 1 registered 10:53:04.047 CNTRLR beginning interview... 10:53:04.048 CNTRLR querying version info... 10:53:04.229 SERIAL » 0x01030015e9 (5 bytes) 10:53:04.232 DRIVER » [REQ] [GetControllerVersion] 10:53:04.238 SERIAL « [ACK] (0x06) 10:53:04.242 SERIAL « 0x011001155a2d5761766520332e3935000199 (18 bytes) 10:53:04.244 SERIAL » [ACK] (0x06) 10:53:04.246 DRIVER « [RES] [GetControllerVersion] payload: 0x5a2d5761766520332e39350001 10:53:04.257 CNTRLR received version info: controller type: Static Controller library version: Z-Wave 3.95 10:53:04.258 CNTRLR querying controller IDs... 10:53:04.266 SERIAL » 0x01030020dc (5 bytes) 10:53:04.267 DRIVER » [REQ] [GetControllerId] 10:53:04.270 SERIAL « [ACK] (0x06) 10:53:04.272 SERIAL « 0x01080120dc3452b301de (10 bytes) 10:53:04.274 SERIAL » [ACK] (0x06) 10:53:04.275 DRIVER « [RES] [GetControllerId] payload: 0xdc3452b301 10:53:04.282 CNTRLR received controller IDs: home ID: 0xdc3452b3 own node ID: 1 10:53:04.283 CNTRLR querying controller capabilities... 10:53:04.290 SERIAL » 0x01030005f9 (5 bytes) 10:53:04.291 DRIVER » [REQ] [GetControllerCapabilities] 10:53:04.294 SERIAL « [ACK] (0x06) 10:53:04.296 SERIAL « 0x010401051ce3 (6 bytes) 10:53:04.297 SERIAL » [ACK] (0x06) 10:53:04.299 DRIVER « [RES] [GetControllerCapabilities] payload: 0x1c 10:53:04.314 CNTRLR received controller capabilities: controller role: primary is in other network: false is SIS present: true was real primary: true is a SUC: true 10:53:04.315 CNTRLR querying API capabilities... 10:53:04.322 SERIAL » 0x01030007fb (5 bytes) 10:53:04.323 DRIVER » [REQ] [GetSerialApiCapabilities] 10:53:04.327 SERIAL « [ACK] (0x06) 10:53:04.329 SERIAL « 0x012b0107010000860001005afe81ff884f1f0000fb9f7da067000080008086000 (45 bytes) 000e87300000e0000600000fb 10:53:04.332 SERIAL » [ACK] (0x06) 10:53:04.334 DRIVER « [RES] [GetSerialApiCapabilities] payload: 0x010000860001005afe81ff884f1f0000fb9f7da067000080008086000000e8730 0000e0000600000 10:53:04.341 CNTRLR received API capabilities: serial API version: 1.0 manufacturer ID: 0x86 product type: 0x01 product ID: 0x5a supported functions: · GetSerialApiInitData (0x02) · FUNC_ID_SERIAL_API_APPL_NODE_INFORMATION (0x03) · ApplicationCommand (0x04) · GetControllerCapabilities (0x05) · SetSerialApiTimeouts (0x06) · GetSerialApiCapabilities (0x07) · FUNC_ID_SERIAL_API_SOFT_RESET (0x08) · UNKNOWN_FUNC_UNKNOWN_0x09 (0x09) · UNKNOWN_FUNC_RF_RECEIVE_MODE (0x10) · UNKNOWN_FUNC_SET_SLEEP_MODE (0x11) · FUNC_ID_ZW_SEND_NODE_INFORMATION (0x12) · SendData (0x13) · SendDataMulticast (0x14) · GetControllerVersion (0x15) · SendDataAbort (0x16) · FUNC_ID_ZW_R_F_POWER_LEVEL_SET (0x17) · UNKNOWN_FUNC_SEND_DATA_META (0x18) · FUNC_ID_ZW_GET_RANDOM (0x1c) · GetControllerId (0x20) · UNKNOWN_FUNC_MEMORY_GET_BYTE (0x21) · UNKNOWN_FUNC_MEMORY_PUT_BYTE (0x22) · UNKNOWN_FUNC_MEMORY_GET_BUFFER (0x23) · UNKNOWN_FUNC_MEMORY_PUT_BUFFER (0x24) · UNKNOWN_FUNC_FlashAutoProgSet (0x27) · UNKNOWN_FUNC_NVMGetId (0x29) · UNKNOWN_FUNC_NVMExtReadLongBuffer (0x2a) · UNKNOWN_FUNC_NVMExtWriteLongBuffer (0x2b) · UNKNOWN_FUNC_NVMExtReadLongByte (0x2c) · UNKNOWN_FUNC_NVMExtWriteLongByte (0x2d) · GetNodeProtocolInfo (0x41) · HardReset (0x42) · FUNC_ID_ZW_REPLICATION_COMMAND_COMPLETE (0x44) · FUNC_ID_ZW_REPLICATION_SEND_DATA (0x45) · AssignReturnRoute (0x46) · DeleteReturnRoute (0x47) · RequestNodeNeighborUpdate (0x48) · ApplicationUpdateRequest (0x49) · AddNodeToNetwork (0x4a) · RemoveNodeFromNetwork (0x4b) · FUNC_ID_ZW_CREATE_NEW_PRIMARY (0x4c) · FUNC_ID_ZW_CONTROLLER_CHANGE (0x4d) · FUNC_ID_ZW_SET_LEARN_MODE (0x50) · AssignSUCReturnRoute (0x51) · FUNC_ID_ZW_REQUEST_NETWORK_UPDATE (0x53) · SetSUCNodeId (0x54) · DeleteSUCReturnRoute (0x55) · GetSUCNodeId (0x56) · UNKNOWN_FUNC_SEND_SUC_ID (0x57) · FUNC_ID_ZW_EXPLORE_REQUEST_INCLUSION (0x5e) · RequestNodeInfo (0x60) · RemoveFailedNode (0x61) · IsFailedNode (0x62) · ReplaceFailedNode (0x63) · UNKNOWN_FUNC_UNKNOWN_0x66 (0x66) · UNKNOWN_FUNC_UNKNOWN_0x67 (0x67) · GetRoutingInfo (0x80) · UNKNOWN_FUNC_LOCK_ROUTE_RESPONSE (0x90) · UNKNOWN_FUNC_GET_PRIORITY_ROUTE (0x92) · UNKNOWN_FUNC_SET_PRIORITY_ROUTE (0x93) · UNKNOWN_FUNC_UNKNOWN_0x98 (0x98) · UNKNOWN_FUNC_UNKNOWN_0xB4 (0xb4) · UNKNOWN_FUNC_WATCH_DOG_ENABLE (0xb6) · UNKNOWN_FUNC_WATCH_DOG_DISABLE (0xb7) · UNKNOWN_FUNC_WATCH_DOG_KICK (0xb8) · UNKNOWN_FUNC_UNKNOWN_0xB9 (0xb9) · UNKNOWN_FUNC_RF_POWERLEVEL_GET (0xba) · UNKNOWN_FUNC_GET_LIBRARY_TYPE (0xbd) · UNKNOWN_FUNC_SEND_TEST_FRAME (0xbe) · UNKNOWN_FUNC_GET_PROTOCOL_STATUS (0xbf) · UNKNOWN_FUNC_UNKNOWN_0xD2 (0xd2) · UNKNOWN_FUNC_UNKNOWN_0xD3 (0xd3) · UNKNOWN_FUNC_UNKNOWN_0xD4 (0xd4) · undefined (0xee) · UNKNOWN_FUNC_UNKNOWN_0xEF (0xef) 10:53:04.345 CNTRLR finding SUC... 10:53:04.352 SERIAL » 0x01030056aa (5 bytes) 10:53:04.354 DRIVER » [REQ] [GetSUCNodeId] 10:53:04.357 SERIAL « [ACK] (0x06) 10:53:04.359 SERIAL « 0x0104015601ad (6 bytes) 10:53:04.361 SERIAL » [ACK] (0x06) 10:53:04.362 DRIVER « [RES] [GetSUCNodeId] payload: 0x01 10:53:04.375 CNTRLR This is the SUC 10:53:04.740 CNTRLR querying node information... 10:53:04.748 SERIAL » 0x01030002fe (5 bytes) 10:53:04.749 DRIVER » [REQ] [GetSerialApiInitData] 10:53:04.760 SERIAL « [ACK] (0x06) 10:53:04.852 SERIAL « 0x0125010205081ddf01e8f30700000000000000000000000000000000000000000 (39 bytes) 000000005000e 10:53:04.853 SERIAL » [ACK] (0x06) 10:53:04.854 DRIVER « [RES] [GetSerialApiInitData] payload: 0x05081ddf01e8f3070000000000000000000000000000000000000000000000000 500 10:53:04.860 CNTRLR received node information: controller role: primary controller is a SUC: true controller is a slave: false controller supports timers: false nodes in the network: 1, 2, 3, 4, 5, 7, 8, 9, 20, 22, 23, 24, 25, 26, 29, 30, 31, 32, 33, 34, 35 10:53:04.928 DRIVER Cache file for homeId 0xdc3452b3 found, attempting to restore the network from cache... 10:53:05.024 CNTRLR [Node 001] Embedded device config loaded 10:53:05.042 CNTRLR [Node 002] Embedded device config loaded 10:53:05.051 CNTRLR [Node 003] Embedded device config loaded 10:53:05.060 CNTRLR [Node 004] Embedded device config loaded 10:53:05.069 CNTRLR [Node 005] Embedded device config loaded 10:53:05.076 CNTRLR [Node 007] Embedded device config loaded 10:53:05.085 CNTRLR [Node 008] Embedded device config loaded 10:53:05.093 CNTRLR [Node 009] Embedded device config loaded 10:53:05.110 CNTRLR [Node 020] Embedded device config loaded 10:53:05.118 CNTRLR [Node 022] Embedded device config loaded 10:53:05.128 CNTRLR [Node 023] Embedded device config loaded 10:53:05.136 CNTRLR [Node 024] Embedded device config loaded 10:53:05.148 CNTRLR [Node 025] Embedded device config loaded 10:53:05.156 CNTRLR [Node 026] Embedded device config loaded 10:53:05.166 CNTRLR [Node 029] Embedded device config loaded 10:53:05.176 CNTRLR [Node 030] Embedded device config loaded 10:53:05.187 CNTRLR [Node 031] Embedded device config loaded 10:53:05.196 CNTRLR [Node 032] Embedded device config loaded 10:53:05.208 CNTRLR [Node 033] Embedded device config loaded 10:53:05.217 CNTRLR [Node 034] Embedded device config loaded 10:53:05.225 CNTRLR [Node 035] Embedded device config loaded 10:53:05.226 DRIVER Restoring the network from cache was successful! 10:53:05.232 CNTRLR [Node 001] [Manufacturer Specific] manufacturerId: metadata updated 10:53:05.233 CNTRLR [Node 001] [Manufacturer Specific] productType: metadata updated 10:53:05.234 CNTRLR [Node 001] [Manufacturer Specific] productId: metadata updated 10:53:05.236 CNTRLR [Node 001] [~] [Manufacturer Specific] manufacturerId: 134 => 134 10:53:05.238 CNTRLR [Node 001] [~] [Manufacturer Specific] productType: 1 => 1 10:53:05.239 CNTRLR [Node 001] [~] [Manufacturer Specific] productId: 90 => 90 10:53:05.240 CNTRLR setting serial API timeouts: ack = 1000 ms, byte = 150 ms 10:53:05.246 SERIAL » 0x01050006640f97 (7 bytes) 10:53:05.247 DRIVER » [REQ] [SetSerialApiTimeouts] payload: 0x640f 10:53:05.252 SERIAL « [ACK] (0x06) 10:53:05.254 SERIAL « 0x01050106640f96 (7 bytes) 10:53:05.255 SERIAL » [ACK] (0x06) 10:53:05.256 DRIVER « [RES] [SetSerialApiTimeouts] payload: 0x640f 10:53:05.262 CNTRLR serial API timeouts overwritten. The old values were: ack = 1000 ms, byte = 15 0 ms 10:53:05.262 CNTRLR Interview completed 10:53:05.265 DRIVER driver ready 2021-05-22 10:53:05.266 - info: zwave2.0 (26343) The driver is ready. Found 21 nodes. 10:53:05.271 CNTRLR [Node 001] The node is alive. 10:53:05.272 CNTRLR [Node 001] The node is ready to be used 10:53:05.273 CNTRLR » [Node 002] pinging the node... 10:53:05.444 SERIAL » 0x010800130201002501c3 (10 bytes) 10:53:05.445 DRIVER » [Node 002] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 1 └─[NoOperationCC] 10:53:05.447 CNTRLR » [Node 003] pinging the node... 10:53:05.449 CNTRLR » [Node 004] pinging the node... 10:53:05.461 CNTRLR » [Node 005] pinging the node... 10:53:05.472 CNTRLR [Node 007] The node is asleep. 10:53:05.475 CNTRLR [Node 007] The node is ready to be used 10:53:05.477 CNTRLR [Node 008] The node is asleep. 10:53:05.479 CNTRLR [Node 008] The node is ready to be used 10:53:05.480 CNTRLR » [Node 008] Assigning SUC return route... 10:53:05.484 CNTRLR [Node 009] The node is asleep. 10:53:05.486 CNTRLR [Node 009] The node is ready to be used 10:53:05.487 CNTRLR » [Node 009] Assigning SUC return route... 10:53:05.491 CNTRLR [Node 020] The node is asleep. 10:53:05.492 CNTRLR [Node 020] The node is ready to be used 10:53:05.493 CNTRLR » [Node 020] Assigning SUC return route... 10:53:05.496 CNTRLR » [Node 022] pinging the node... 10:53:05.500 CNTRLR [Node 023] The node is asleep. 10:53:05.502 CNTRLR [Node 023] The node is ready to be used 10:53:05.503 CNTRLR » [Node 023] Assigning SUC return route... 10:53:05.507 CNTRLR [Node 024] The node is asleep. 10:53:05.509 CNTRLR [Node 024] The node is ready to be used 10:53:05.510 CNTRLR [Node 025] The node is asleep. 10:53:05.512 CNTRLR [Node 025] The node is ready to be used 10:53:05.513 CNTRLR » [Node 025] Assigning SUC return route... 10:53:05.517 CNTRLR » [Node 026] pinging the node... 10:53:05.520 CNTRLR » [Node 029] pinging the node... 10:53:05.524 CNTRLR » [Node 030] pinging the node... 10:53:05.527 CNTRLR » [Node 031] pinging the node... 10:53:05.530 CNTRLR » [Node 032] pinging the node... 10:53:05.534 CNTRLR » [Node 033] pinging the node... 10:53:05.537 CNTRLR » [Node 034] pinging the node... 10:53:05.540 CNTRLR » [Node 035] pinging the node... 10:53:05.548 SERIAL « [ACK] (0x06) 10:53:05.552 SERIAL « 0x0104011301e8 (6 bytes) 10:53:05.554 SERIAL » [ACK] (0x06) 10:53:05.556 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:05.574 - info: zwave2.0 (26343) Node 1: ready to use 2021-05-22 10:53:05.863 - info: zwave2.0 (26343) Node 7: ready to use 2021-05-22 10:53:05.890 - info: zwave2.0 (26343) Node 8: ready to use 2021-05-22 10:53:05.913 - info: zwave2.0 (26343) Node 9: ready to use 2021-05-22 10:53:05.960 - info: zwave2.0 (26343) Node 20: ready to use 2021-05-22 10:53:06.287 - debug: zwave2.0 (26343) object zwave2.0.Node_022.Multilevel_Switch.up changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Up)"},"native":{"nodeId":22,"valueId":{"commandClass":38,"endpoint":0,"property":"Up"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673586180,"_id":"zwave2.0.Node_022.Multilevel_Switch.up","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:06.353 - debug: zwave2.0 (26343) object zwave2.0.Node_022.Multilevel_Switch.down changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Down)"},"native":{"nodeId":22,"valueId":{"commandClass":38,"endpoint":0,"property":"Down"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673586319,"_id":"zwave2.0.Node_022.Multilevel_Switch.down","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:06.650 - info: zwave2.0 (26343) Node 23: ready to use 2021-05-22 10:53:06.675 - info: zwave2.0 (26343) Node 24: ready to use 2021-05-22 10:53:06.712 - info: zwave2.0 (26343) Node 25: ready to use 2021-05-22 10:53:06.793 - debug: zwave2.0 (26343) object zwave2.0.Node_026.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":26,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673586786,"_id":"zwave2.0.Node_026.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 10:53:06.804 SERIAL « 0x010700130100007d97 (9 bytes) 10:53:06.805 SERIAL » [ACK] (0x06) 10:53:06.808 DRIVER « [REQ] [SendData] callback id: 1 transmit status: OK 10:53:06.818 SERIAL » 0x010800130301002502c1 (10 bytes) 10:53:06.819 DRIVER » [Node 003] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 2 └─[NoOperationCC] 10:53:06.820 CNTRLR [Node 002] The node is alive. 10:53:06.821 CNTRLR [Node 002] The node is ready to be used 2021-05-22 10:53:06.822 - info: zwave2.0 (26343) Node 2: ready to use 10:53:06.823 CNTRLR « [Node 002] ping successful 2021-05-22 10:53:06.827 - debug: zwave2.0 (26343) object zwave2.0.Node_026.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":26,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673586799,"_id":"zwave2.0.Node_026.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 10:53:06.828 SERIAL « [ACK] (0x06) 10:53:06.831 SERIAL « 0x0104011301e8 (6 bytes) 10:53:06.832 SERIAL » [ACK] (0x06) 10:53:06.834 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:06.852 - info: zwave2.0 (26343) Node 2 is alive 2021-05-22 10:53:06.917 - debug: zwave2.0 (26343) object zwave2.0.Node_026.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":26,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673586900,"_id":"zwave2.0.Node_026.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.303 - debug: zwave2.0 (26343) object zwave2.0.Node_029.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":29,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587297,"_id":"zwave2.0.Node_029.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.315 - debug: zwave2.0 (26343) object zwave2.0.Node_029.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":29,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587307,"_id":"zwave2.0.Node_029.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.337 - debug: zwave2.0 (26343) object zwave2.0.Node_029.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":29,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587330,"_id":"zwave2.0.Node_029.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.414 - debug: zwave2.0 (26343) object zwave2.0.Node_030.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":30,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587409,"_id":"zwave2.0.Node_030.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.428 - debug: zwave2.0 (26343) object zwave2.0.Node_030.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":30,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587421,"_id":"zwave2.0.Node_030.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.446 - debug: zwave2.0 (26343) object zwave2.0.Node_030.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":30,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587439,"_id":"zwave2.0.Node_030.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.514 - debug: zwave2.0 (26343) object zwave2.0.Node_031.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":31,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587509,"_id":"zwave2.0.Node_031.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.521 - debug: zwave2.0 (26343) object zwave2.0.Node_031.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":31,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587517,"_id":"zwave2.0.Node_031.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.535 - debug: zwave2.0 (26343) object zwave2.0.Node_031.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":31,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587531,"_id":"zwave2.0.Node_031.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.588 - debug: zwave2.0 (26343) object zwave2.0.Node_032.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":32,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587584,"_id":"zwave2.0.Node_032.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.595 - debug: zwave2.0 (26343) object zwave2.0.Node_032.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":32,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587591,"_id":"zwave2.0.Node_032.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.611 - debug: zwave2.0 (26343) object zwave2.0.Node_032.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":32,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587605,"_id":"zwave2.0.Node_032.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.671 - debug: zwave2.0 (26343) object zwave2.0.Node_033.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":33,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587667,"_id":"zwave2.0.Node_033.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.678 - debug: zwave2.0 (26343) object zwave2.0.Node_033.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":33,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587674,"_id":"zwave2.0.Node_033.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.693 - debug: zwave2.0 (26343) object zwave2.0.Node_033.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":33,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587689,"_id":"zwave2.0.Node_033.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.748 - debug: zwave2.0 (26343) object zwave2.0.Node_034.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":34,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587743,"_id":"zwave2.0.Node_034.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.755 - debug: zwave2.0 (26343) object zwave2.0.Node_034.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":34,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587751,"_id":"zwave2.0.Node_034.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.774 - debug: zwave2.0 (26343) object zwave2.0.Node_034.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":34,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587770,"_id":"zwave2.0.Node_034.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.829 - debug: zwave2.0 (26343) object zwave2.0.Node_035.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":35,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587826,"_id":"zwave2.0.Node_035.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.836 - debug: zwave2.0 (26343) object zwave2.0.Node_035.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":35,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587832,"_id":"zwave2.0.Node_035.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:07.850 - debug: zwave2.0 (26343) object zwave2.0.Node_035.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":35,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673587846,"_id":"zwave2.0.Node_035.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 10:53:08.080 SERIAL « 0x010700130200007d94 (9 bytes) 10:53:08.081 SERIAL » [ACK] (0x06) 10:53:08.082 DRIVER « [REQ] [SendData] callback id: 2 transmit status: OK 10:53:08.090 SERIAL » 0x010800130401002503c7 (10 bytes) 10:53:08.091 DRIVER » [Node 004] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 3 └─[NoOperationCC] 10:53:08.092 CNTRLR [Node 003] The node is alive. 10:53:08.093 CNTRLR [Node 003] The node is ready to be used 2021-05-22 10:53:08.094 - info: zwave2.0 (26343) Node 3: ready to use 10:53:08.095 CNTRLR « [Node 003] ping successful 10:53:08.099 SERIAL « [ACK] (0x06) 10:53:08.104 SERIAL « 0x0104011301e8 (6 bytes) 10:53:08.105 SERIAL » [ACK] (0x06) 10:53:08.107 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:08.115 - info: zwave2.0 (26343) Node 3 is alive 10:53:09.707 SERIAL « 0x01070013030000a149 (9 bytes) 10:53:09.708 SERIAL » [ACK] (0x06) 10:53:09.709 DRIVER « [REQ] [SendData] callback id: 3 transmit status: OK 10:53:09.726 SERIAL » 0x010800130501002504c1 (10 bytes) 10:53:09.727 DRIVER » [Node 005] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 4 └─[NoOperationCC] 10:53:09.730 CNTRLR [Node 004] The node is alive. 10:53:09.737 CNTRLR [Node 004] The node is ready to be used 2021-05-22 10:53:09.738 - info: zwave2.0 (26343) Node 4: ready to use 10:53:09.740 CNTRLR « [Node 004] ping successful 10:53:09.744 SERIAL « [ACK] (0x06) 10:53:09.751 SERIAL « 0x0104011301e8 (6 bytes) 10:53:09.752 SERIAL » [ACK] (0x06) 10:53:09.755 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:09.769 - info: zwave2.0 (26343) Node 4 is alive 10:53:11.274 SERIAL « 0x010700130400009a75 (9 bytes) 10:53:11.275 SERIAL » [ACK] (0x06) 10:53:11.278 DRIVER « [REQ] [SendData] callback id: 4 transmit status: OK 10:53:11.297 SERIAL » 0x010800131601002505d3 (10 bytes) 10:53:11.299 DRIVER » [Node 022] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 5 └─[NoOperationCC] 10:53:11.301 CNTRLR [Node 005] The node is alive. 10:53:11.303 CNTRLR [Node 005] The node is ready to be used 2021-05-22 10:53:11.304 - info: zwave2.0 (26343) Node 5: ready to use 10:53:11.305 CNTRLR « [Node 005] ping successful 10:53:11.310 SERIAL « [ACK] (0x06) 10:53:11.314 SERIAL « 0x0104011301e8 (6 bytes) 10:53:11.315 SERIAL » [ACK] (0x06) 10:53:11.318 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:11.561 - info: zwave2.0 (26343) Node 5 is alive 10:53:12.920 SERIAL « 0x01070013050000a14f (9 bytes) 10:53:12.921 SERIAL » [ACK] (0x06) 10:53:12.923 DRIVER « [REQ] [SendData] callback id: 5 transmit status: OK 10:53:12.937 SERIAL » 0x010800131a01002506dc (10 bytes) 10:53:12.939 DRIVER » [Node 026] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 6 └─[NoOperationCC] 10:53:12.941 CNTRLR [Node 022] The node is alive. 10:53:12.942 CNTRLR [Node 022] The node is ready to be used 2021-05-22 10:53:12.943 - info: zwave2.0 (26343) Node 22: ready to use 10:53:12.945 CNTRLR « [Node 022] ping successful 10:53:12.948 SERIAL « [ACK] (0x06) 10:53:12.953 SERIAL « 0x0104011301e8 (6 bytes) 10:53:12.954 SERIAL » [ACK] (0x06) 10:53:12.955 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:12.965 - info: zwave2.0 (26343) Node 22 is alive 10:53:12.975 SERIAL « 0x0107001306000002ef (9 bytes) 10:53:12.977 SERIAL » [ACK] (0x06) 10:53:12.979 DRIVER « [REQ] [SendData] callback id: 6 transmit status: OK 10:53:12.991 SERIAL » 0x010800131d01002507da (10 bytes) 10:53:12.992 DRIVER » [Node 029] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 7 └─[NoOperationCC] 10:53:12.994 CNTRLR [Node 026] The node is alive. 10:53:12.996 CNTRLR [Node 026] The node is ready to be used 2021-05-22 10:53:12.996 - info: zwave2.0 (26343) Node 26: ready to use 10:53:12.998 CNTRLR « [Node 026] ping successful 10:53:13.015 SERIAL « [ACK] (0x06) 10:53:13.020 SERIAL « 0x0104011301e8 (6 bytes) 10:53:13.021 SERIAL » [ACK] (0x06) 10:53:13.024 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:13.037 - info: zwave2.0 (26343) Node 26 is alive 2021-05-22 10:53:13.050 - debug: zwave2.0 (26343) object zwave2.0.Node_022.Multilevel_Switch.up changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Up)"},"native":{"nodeId":22,"valueId":{"commandClass":38,"endpoint":0,"property":"Up"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593041,"_id":"zwave2.0.Node_022.Multilevel_Switch.up","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 10:53:13.063 SERIAL « 0x0107001307000006ea (9 bytes) 10:53:13.064 SERIAL » [ACK] (0x06) 10:53:13.065 DRIVER « [REQ] [SendData] callback id: 7 transmit status: OK 10:53:13.073 SERIAL » 0x010800131e01002508d6 (10 bytes) 10:53:13.074 DRIVER » [Node 030] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 8 └─[NoOperationCC] 10:53:13.075 CNTRLR [Node 029] The node is alive. 10:53:13.076 CNTRLR [Node 029] The node is ready to be used 2021-05-22 10:53:13.077 - info: zwave2.0 (26343) Node 29: ready to use 10:53:13.078 CNTRLR « [Node 029] ping successful 10:53:13.083 SERIAL « [ACK] (0x06) 10:53:13.088 SERIAL « 0x0104011301e8 (6 bytes) 10:53:13.090 SERIAL » [ACK] (0x06) 10:53:13.092 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:13.100 - debug: zwave2.0 (26343) object zwave2.0.Node_022.Multilevel_Switch.down changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Down)"},"native":{"nodeId":22,"valueId":{"commandClass":38,"endpoint":0,"property":"Down"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593082,"_id":"zwave2.0.Node_022.Multilevel_Switch.down","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.106 - info: zwave2.0 (26343) Node 29 is alive 2021-05-22 10:53:13.125 - debug: zwave2.0 (26343) object zwave2.0.Node_026.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":26,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593111,"_id":"zwave2.0.Node_026.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.137 - debug: zwave2.0 (26343) object zwave2.0.Node_026.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":26,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593130,"_id":"zwave2.0.Node_026.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.148 - debug: zwave2.0 (26343) object zwave2.0.Node_029.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":29,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593142,"_id":"zwave2.0.Node_029.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.158 - debug: zwave2.0 (26343) object zwave2.0.Node_029.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":29,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593152,"_id":"zwave2.0.Node_029.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 10:53:13.168 SERIAL « 0x0107001308000009ea (9 bytes) 10:53:13.169 SERIAL » [ACK] (0x06) 2021-05-22 10:53:13.170 - debug: zwave2.0 (26343) object zwave2.0.Node_026.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":26,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593163,"_id":"zwave2.0.Node_026.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 10:53:13.172 DRIVER « [REQ] [SendData] callback id: 8 transmit status: OK 10:53:13.181 SERIAL » 0x010800131f01002509d6 (10 bytes) 10:53:13.183 DRIVER » [Node 031] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 9 └─[NoOperationCC] 10:53:13.184 CNTRLR [Node 030] The node is alive. 10:53:13.185 CNTRLR [Node 030] The node is ready to be used 2021-05-22 10:53:13.186 - info: zwave2.0 (26343) Node 30: ready to use 10:53:13.187 CNTRLR « [Node 030] ping successful 10:53:13.191 SERIAL « [ACK] (0x06) 10:53:13.198 SERIAL « 0x0104011301e8 (6 bytes) 10:53:13.199 SERIAL » [ACK] (0x06) 10:53:13.201 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:13.209 - info: zwave2.0 (26343) Node 30 is alive 10:53:13.212 SERIAL « 0x0107001309000002e0 (9 bytes) 10:53:13.213 SERIAL » [ACK] (0x06) 10:53:13.214 DRIVER « [REQ] [SendData] callback id: 9 transmit status: OK 10:53:13.229 SERIAL » 0x01080013200100250aea (10 bytes) 10:53:13.230 DRIVER » [Node 032] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 10 └─[NoOperationCC] 10:53:13.231 CNTRLR [Node 031] The node is alive. 10:53:13.233 CNTRLR [Node 031] The node is ready to be used 2021-05-22 10:53:13.234 - info: zwave2.0 (26343) Node 31: ready to use 10:53:13.235 CNTRLR « [Node 031] ping successful 10:53:13.239 SERIAL « [ACK] (0x06) 10:53:13.250 SERIAL « 0x0104011301e8 (6 bytes) 10:53:13.251 SERIAL » [ACK] (0x06) 2021-05-22 10:53:13.253 - debug: zwave2.0 (26343) object zwave2.0.Node_029.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":29,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593238,"_id":"zwave2.0.Node_029.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 10:53:13.255 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:13.260 - info: zwave2.0 (26343) Node 31 is alive 10:53:13.261 SERIAL « 0x010700130a000002e3 (9 bytes) 10:53:13.262 SERIAL » [ACK] (0x06) 10:53:13.263 DRIVER « [REQ] [SendData] callback id: 10 transmit status: OK 10:53:13.270 SERIAL » 0x01080013210100250bea (10 bytes) 10:53:13.271 DRIVER » [Node 033] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 11 └─[NoOperationCC] 10:53:13.272 CNTRLR [Node 032] The node is alive. 10:53:13.273 CNTRLR [Node 032] The node is ready to be used 2021-05-22 10:53:13.273 - info: zwave2.0 (26343) Node 32: ready to use 10:53:13.274 CNTRLR « [Node 032] ping successful 10:53:13.278 SERIAL « [ACK] (0x06) 10:53:13.285 SERIAL « 0x0104011301e8 (6 bytes) 10:53:13.286 SERIAL » [ACK] (0x06) 10:53:13.288 DRIVER « [RES] [SendData] was sent: true 10:53:13.307 SERIAL « 0x010700130b000002e2 (9 bytes) 10:53:13.307 SERIAL » [ACK] (0x06) 2021-05-22 10:53:13.309 - info: zwave2.0 (26343) Node 32 is alive 10:53:13.311 DRIVER « [REQ] [SendData] callback id: 11 transmit status: OK 10:53:13.318 SERIAL » 0x01080013220100250cee (10 bytes) 10:53:13.319 DRIVER » [Node 034] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 12 └─[NoOperationCC] 10:53:13.320 CNTRLR [Node 033] The node is alive. 10:53:13.321 CNTRLR [Node 033] The node is ready to be used 2021-05-22 10:53:13.321 - info: zwave2.0 (26343) Node 33: ready to use 10:53:13.322 CNTRLR « [Node 033] ping successful 10:53:13.329 SERIAL « [ACK] (0x06) 10:53:13.332 SERIAL « 0x0104011301e8 (6 bytes) 10:53:13.334 SERIAL » [ACK] (0x06) 10:53:13.338 DRIVER « [RES] [SendData] was sent: true 10:53:13.357 SERIAL « 0x010700130c000002e5 (9 bytes) 10:53:13.358 SERIAL » [ACK] (0x06) 10:53:13.359 DRIVER « [REQ] [SendData] callback id: 12 transmit status: OK 10:53:13.368 SERIAL » 0x01080013230100250dee (10 bytes) 10:53:13.369 DRIVER » [Node 035] [REQ] [SendData] │ transmit options: 0x25 │ callback id: 13 └─[NoOperationCC] 10:53:13.370 CNTRLR [Node 034] The node is alive. 10:53:13.371 CNTRLR [Node 034] The node is ready to be used 2021-05-22 10:53:13.371 - info: zwave2.0 (26343) Node 34: ready to use 10:53:13.372 CNTRLR « [Node 034] ping successful 10:53:13.384 SERIAL « [ACK] (0x06) 10:53:13.389 SERIAL « 0x0104011301e8 (6 bytes) 10:53:13.390 SERIAL » [ACK] (0x06) 2021-05-22 10:53:13.393 - info: zwave2.0 (26343) Node 33 is alive 10:53:13.395 DRIVER « [RES] [SendData] was sent: true 2021-05-22 10:53:13.419 - info: zwave2.0 (26343) Node 34 is alive 10:53:13.433 SERIAL « 0x010700130d000005e3 (9 bytes) 10:53:13.434 SERIAL » [ACK] (0x06) 10:53:13.435 DRIVER « [REQ] [SendData] callback id: 13 transmit status: OK 10:53:13.447 CNTRLR [Node 035] The node is alive. 10:53:13.448 CNTRLR [Node 035] The node is ready to be used 10:53:13.449 CNTRLR All nodes are ready to be used 2021-05-22 10:53:13.450 - info: zwave2.0 (26343) All nodes are ready to use 2021-05-22 10:53:13.451 - info: zwave2.0 (26343) Node 35: ready to use 10:53:13.514 CNTRLR « [Node 035] ping successful 2021-05-22 10:53:13.562 - info: zwave2.0 (26343) Node 35 is alive 2021-05-22 10:53:13.571 - debug: zwave2.0 (26343) object zwave2.0.Node_030.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":30,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593544,"_id":"zwave2.0.Node_030.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.590 - debug: zwave2.0 (26343) object zwave2.0.Node_031.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":31,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593576,"_id":"zwave2.0.Node_031.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.614 - debug: zwave2.0 (26343) object zwave2.0.Node_032.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":32,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593585,"_id":"zwave2.0.Node_032.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.617 - debug: zwave2.0 (26343) object zwave2.0.Node_030.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":30,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593591,"_id":"zwave2.0.Node_030.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.646 - debug: zwave2.0 (26343) object zwave2.0.Node_033.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":33,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593618,"_id":"zwave2.0.Node_033.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.647 - debug: zwave2.0 (26343) object zwave2.0.Node_031.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":31,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593623,"_id":"zwave2.0.Node_031.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.650 - debug: zwave2.0 (26343) object zwave2.0.Node_034.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":34,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593623,"_id":"zwave2.0.Node_034.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 10:53:13.685 DRIVER Usage statistics sent - next transmission scheduled in 23 hours. 2021-05-22 10:53:13.704 - debug: zwave2.0 (26343) object zwave2.0.Node_032.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":32,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593660,"_id":"zwave2.0.Node_032.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.713 - debug: zwave2.0 (26343) object zwave2.0.Node_033.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":33,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593663,"_id":"zwave2.0.Node_033.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.736 - debug: zwave2.0 (26343) object zwave2.0.Node_035.Multilevel_Switch.open changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Open)"},"native":{"nodeId":35,"valueId":{"commandClass":38,"endpoint":0,"property":"Open"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593707,"_id":"zwave2.0.Node_035.Multilevel_Switch.open","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.780 - debug: zwave2.0 (26343) object zwave2.0.Node_034.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":34,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593707,"_id":"zwave2.0.Node_034.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.807 - debug: zwave2.0 (26343) object zwave2.0.Node_030.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":30,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593792,"_id":"zwave2.0.Node_030.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.838 - debug: zwave2.0 (26343) object zwave2.0.Node_035.Multilevel_Switch.close changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Perform a level change (Close)"},"native":{"nodeId":35,"valueId":{"commandClass":38,"endpoint":0,"property":"Close"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593802,"_id":"zwave2.0.Node_035.Multilevel_Switch.close","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.854 - debug: zwave2.0 (26343) object zwave2.0.Node_031.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":31,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593832,"_id":"zwave2.0.Node_031.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.887 - debug: zwave2.0 (26343) object zwave2.0.Node_032.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":32,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593878,"_id":"zwave2.0.Node_032.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.893 - debug: zwave2.0 (26343) object zwave2.0.Node_033.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":33,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593880,"_id":"zwave2.0.Node_033.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.894 - debug: zwave2.0 (26343) object zwave2.0.Node_034.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":34,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593884,"_id":"zwave2.0.Node_034.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} 2021-05-22 10:53:13.949 - debug: zwave2.0 (26343) object zwave2.0.Node_035.Central_Scene.slowRefresh changed: {"type":"state","common":{"type":"boolean","read":true,"write":true,"role":"switch","name":"Send held down notifications at a slow rate","desc":"When this is true, KeyHeldDown notifications are sent every 55s. When this is false, the notifications are sent every 200ms."},"native":{"nodeId":35,"valueId":{"commandClass":91,"endpoint":0,"property":"slowRefresh"}},"from":"system.adapter.zwave2.0","user":"system.user.admin","ts":1621673593926,"_id":"zwave2.0.Node_035.Central_Scene.slowRefresh","acl":{"object":1636,"state":1636,"owner":"system.user.admin","ownerGroup":"system.group.administrator"}} -
Man kann die Objekte sehen, die aus meiner alten Installation wieder aufgetaucht sind
aber die Kommunikation scheint nicht gut zu sein, die Werte werden nicht aktualisiert. Befehle werden nicht ausgeführt.
-
Ich habe iobrocker und rasbian zurückgesetzt und Backitup gestartet.
Z-Wave ist angeschlossen und hat die Objekte gefunden, aber es zeigt nicht alle aktuellen Werte an.
Es zeigt mir die aktuellen Werte für einige Objekte, aber nicht für andere.also hier fehlt : currentvalue (ist einfach leer)
und hier zeigt er alles
kann man Backitup nehmen mit zwave als backup ?
-
Na das sieht doch schon besser aus.
@esmax666 sagte in Probleme mit Serialport bei zwave2:
aber es zeigt nicht alle aktuellen Werte an.
Dafür mach mir bitte mal eine Logdatei
https://github.com/AlCalzone/ioBroker.zwave2/blob/master/docs/de/bei-problemen.md#notwendige-informationen-für-ein-issue
und lade sie hier hoch.kann man Backitup nehmen mit zwave als backup
Falls du das meinst, zwave2 ist voll ins iobroker-Backup integriert (welches auch von backitup genutzt wird)
-
Ok also die probleme sind bei "TechniSat Shutter-Switch" z.B hier "node 035" -> "Currentvalue" ist leer (aber auch die andere Technisat)
dc3452b3.values.jsonl dc3452b3.json dc3452b3.metadata.jsonl
ich habe auch schon leer cache gemacht und healh network
ohne erfolg
Ich habe in der Dokumentation nicht gefunden, ob es möglich ist, das Gerät zu zwingen, alle Informationen nochmal zu senden
https://www.technisat.com/en_XX/Roller-shutter-flush-mount,-BJ/352-22704-22938/ -
@esmax666 Mindestens Node 35 ist verschlüsselt eingebunden, antwortet aber nicht auf die verschlüsselten Anfragen. Mein Tip ist auf einem falschen Netzwerkschlüssel in den Adapter-Einstellungen.
-
Ich habe den Schlüssel gewechselt. Ich denke, jetzt ist alles in Ordnung.
Es ist nur seltsam, aber der Webserver reagiert nicht sehr schnell.
Nach ein Click muss ich muss 2-3 Sekunden warten, bis meine Datei in "Objekte" geöffnet wird. Die Reaktivität ist sehr langsam
-
Hi @alcalzone
Das Problem ist wieder da
Habe Adapter und iobroker neu gestartet aber bringt nichts
Was kannst ich sonst noch machen ?
-
No such file or directory
Heißt, dass der USB-Stick nicht mehr den Pfad hat oder gar nicht mehr gefunden wird. Hast du den Host schon mal komplett neu gestartet?
-
@alcalzone raspi ist auch neue gestratet leider ohne erfolg
-
@esmax666 Dann bin ich auch ratlos.
