Einstellungen von Shuttercontrol
-
@stealthangel OK gehen wir mal anderes an... Wenn dein Rollladen im Sonnenschutz fährt, wird im autoState sauber sunProtect gesetzt?
Kannst auch mal den Log posten, wenn der Sonnenschutz aktiviert wird -
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel OK gehen wir mal anderes an... Wenn dein Rollladen im Sonnenschutz fährt, wird im autoState sauber sunProtect gesetzt?
So wie ich das sehe, ja.
Kannst auch mal den Log posten, wenn der Sonnenschutz aktiviert wird
2023-04-01 14:50:00.045 - debug: shuttercontrol.0 (131673) Sun Elevation: 39.6° 2023-04-01 14:50:02.061 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 14:50:02.062 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 14:51:06.770 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 14:51:06.772 - debug: shuttercontrol.0 (131673) Brightness sensor value: 4602 2023-04-01 14:51:06.805 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 14:51:07.862 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: up 2023-04-01 14:51:16.773 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 14:53:27.486 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 14:53:27.487 - debug: shuttercontrol.0 (131673) Brightness sensor value: 4591 2023-04-01 14:53:27.489 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 14:53:28.571 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: up 2023-04-01 14:53:37.488 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 14:55:00.014 - debug: shuttercontrol.0 (131673) calculate astrodata ... 2023-04-01 14:55:00.015 - debug: shuttercontrol.0 (131673) Sun Azimut: 208.4° 2023-04-01 14:55:00.016 - debug: shuttercontrol.0 (131673) Sun Elevation: 39.2° 2023-04-01 14:55:02.024 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 14:55:02.025 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 14:55:33.773 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 14:55:33.774 - debug: shuttercontrol.0 (131673) Brightness sensor value: 4519 2023-04-01 14:55:33.817 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 14:55:34.874 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: up 2023-04-01 14:55:43.776 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 14:58:29.519 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 14:58:29.521 - debug: shuttercontrol.0 (131673) Brightness sensor value: 4320 2023-04-01 14:58:29.525 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 14:58:30.637 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: up 2023-04-01 14:58:39.522 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 15:00:00.029 - debug: shuttercontrol.0 (131673) calculate astrodata ... 2023-04-01 15:00:00.030 - debug: shuttercontrol.0 (131673) Sun Azimut: 210° 2023-04-01 15:00:00.031 - debug: shuttercontrol.0 (131673) Sun Elevation: 38.8° 2023-04-01 15:00:02.047 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:00:02.051 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:00:45.882 - info: web.0 (1054) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-01 15:00:45.941 - info: web.0 (1054) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-01 15:00:45.951 - info: web.0 (1054) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-01 15:00:45.983 - info: web.0 (1054) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-01 15:00:46.194 - info: web.0 (1054) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-01 15:00:54.785 - info: web.0 (1054) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-01 15:01:11.007 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:01:11.008 - debug: shuttercontrol.0 (131673) Brightness sensor value: 4080 2023-04-01 15:01:11.042 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:01:12.101 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: up 2023-04-01 15:01:21.010 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 15:03:38.021 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:03:38.022 - debug: shuttercontrol.0 (131673) Brightness sensor value: 3841 2023-04-01 15:03:38.028 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:03:39.097 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: up 2023-04-01 15:03:48.023 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 15:05:00.046 - debug: shuttercontrol.0 (131673) calculate astrodata ... 2023-04-01 15:05:00.048 - debug: shuttercontrol.0 (131673) Sun Azimut: 211.5° 2023-04-01 15:05:00.049 - debug: shuttercontrol.0 (131673) Sun Elevation: 38.4° 2023-04-01 15:05:02.070 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:05:02.072 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:05:02.116 - debug: shuttercontrol.0 (131673) Büro: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-01 15:05:02.118 - info: shuttercontrol.0 (131673) Sunprotect #416 Set ID: Büro value: 30% 2023-04-01 15:05:02.169 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-01 15:05:02.171 - debug: shuttercontrol.0 (131673) #0 wait for shutter check started 2023-04-01 15:05:02.186 - debug: shuttercontrol.0 (131673) Sunprotect for Büro is active 2023-04-01 15:05:02.187 - debug: shuttercontrol.0 (131673) RangeMinus: 210 < 211.5RangePlus: 390 > 211.5 2023-04-01 15:05:02.187 - debug: shuttercontrol.0 (131673) last automatic Action for Büro: down_Sunprotect 2023-04-01 15:05:02.187 - debug: shuttercontrol.0 (131673) Sunprotect Büro old height: 100% new height: 30% 2023-04-01 15:05:22.172 - debug: shuttercontrol.0 (131673) #0 wait for shutter check end 2023-04-01 15:05:22.177 - debug: shuttercontrol.0 (131673) Shutter state changed: Büro old value = 100 new value = 30 2023-04-01 15:05:22.178 - debug: shuttercontrol.0 (131673) Büro Old value = 100. New value = 30. automatic is active 2023-04-01 15:05:50.509 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:05:50.509 - debug: shuttercontrol.0 (131673) Brightness sensor value: 3875 2023-04-01 15:05:50.541 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:05:50.596 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: sunProtect 2023-04-01 15:06:00.510 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 15:08:52.737 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:08:52.738 - debug: shuttercontrol.0 (131673) Brightness sensor value: 4014 2023-04-01 15:08:52.742 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:08:52.913 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: sunProtect 2023-04-01 15:09:02.740 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 15:10:00.012 - debug: shuttercontrol.0 (131673) calculate astrodata ... 2023-04-01 15:10:00.012 - debug: shuttercontrol.0 (131673) Sun Azimut: 213° 2023-04-01 15:10:00.013 - debug: shuttercontrol.0 (131673) Sun Elevation: 38° 2023-04-01 15:10:02.022 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:10:02.026 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:11:40.501 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:11:40.502 - debug: shuttercontrol.0 (131673) Brightness sensor value: 4138 2023-04-01 15:11:40.539 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:11:40.591 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: sunProtect 2023-04-01 15:11:50.503 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 15:14:13.761 - debug: shuttercontrol.0 (131673) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-01 15:14:13.763 - debug: shuttercontrol.0 (131673) Brightness sensor value: 4158 2023-04-01 15:14:13.800 - debug: shuttercontrol.0 (131673) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-01 15:14:13.856 - debug: shuttercontrol.0 (131673) Lightsensor up Büro already up at: 100% - setting current action: sunProtect 2023-04-01 15:14:23.764 - debug: shuttercontrol.0 (131673) Brightness State Down is: false 2023-04-01 15:15:00.024 - debug: shuttercontrol.0 (131673) calculate astrodata ... 2023-04-01 15:15:00.025 - debug: shuttercontrol.0 (131673) Sun Azimut: 214.5° 2023-04-01 15:15:00.026 - debug: shuttercontrol.0 (131673) Sun Elevation: 37.6° -
@stealthangel Habe es jetzt noch einmal nachgestellt...
Deine Werte für Himmelsrichtung und Range können so nicht passen.
Du kannst dir die richtigen Werte für deinen Standort und dein Fensterausrichtung bei https://www.sonnenverlauf.de ermitteln.Wenn ich aber deine Range sehe, dann kann das nicht passen. Du gibst 300 als Himmelsrichtung ein und eine Range von 90.
Das würde bedeuten, dass bei größer 210 der Sonnenschutz aktiviert wird und bei größer 390 deaktiviert wird.
390 ° gibt es nicht.
Hier sollte der maximale Wert bei 360 liegen.
Wenn ich jetzt aber ein Fenster habe, dass Richtung Westen liegt, dann sollte die Einstellung von 290° und einer Range von 50-60 ° ausreichend sein.Des Weiteren würde ich das Ende des Sonneschutzes im Verhältnis zum schließen de Lichtsensors nicht zu knapp machen. Setze lieber das Ende des Sonnenschutzes auf 12 oder 15
-
@simatec Es ist mir ja schon fast peinlich, aber das war nicht die Lösung.
Die Werte für das Fenster habe ich jetzt angepasst und Elevation steht jetzt auf 15°, aber nix passiert:
2023-04-04 18:09:05.857 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3883 2023-04-04 18:09:15.859 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:10:00.010 - debug: shuttercontrol.0 (144217) calculate astrodata ... 2023-04-04 18:10:00.010 - debug: shuttercontrol.0 (144217) Sun Azimut: 258.1° 2023-04-04 18:10:00.011 - debug: shuttercontrol.0 (144217) Sun Elevation: 16.3° 2023-04-04 18:10:02.020 - debug: shuttercontrol.0 (144217) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-04 18:10:02.021 - debug: shuttercontrol.0 (144217) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-04 18:11:20.335 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3852 2023-04-04 18:11:30.336 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:13:20.378 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3830 2023-04-04 18:13:30.379 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:15:00.018 - debug: shuttercontrol.0 (144217) calculate astrodata ... 2023-04-04 18:15:00.019 - debug: shuttercontrol.0 (144217) Sun Azimut: 259.1° 2023-04-04 18:15:00.020 - debug: shuttercontrol.0 (144217) Sun Elevation: 15.5° 2023-04-04 18:15:02.035 - debug: shuttercontrol.0 (144217) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-04 18:15:02.036 - debug: shuttercontrol.0 (144217) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-04 18:16:09.880 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3807 2023-04-04 18:16:19.881 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:18:45.081 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3789 2023-04-04 18:18:55.082 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:20:00.020 - debug: shuttercontrol.0 (144217) calculate astrodata ... 2023-04-04 18:20:00.021 - debug: shuttercontrol.0 (144217) Sun Azimut: 260.1° 2023-04-04 18:20:00.022 - debug: shuttercontrol.0 (144217) Sun Elevation: 14.7° 2023-04-04 18:20:02.039 - debug: shuttercontrol.0 (144217) Buero level conversion is disabled ... 2023-04-04 18:20:02.039 - debug: shuttercontrol.0 (144217) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-04 18:20:02.041 - debug: shuttercontrol.0 (144217) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-04 18:21:05.884 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3767 2023-04-04 18:21:15.884 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:22:02.041 - debug: shuttercontrol.0 (144217) Buero level conversion is disabled ... 2023-04-04 18:22:02.041 - debug: shuttercontrol.0 (144217) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-04 18:22:02.042 - debug: shuttercontrol.0 (144217) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-04 18:23:12.134 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3761 2023-04-04 18:23:22.136 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:25:00.016 - debug: shuttercontrol.0 (144217) calculate astrodata ... 2023-04-04 18:25:00.016 - debug: shuttercontrol.0 (144217) Sun Azimut: 261.1° 2023-04-04 18:25:00.017 - debug: shuttercontrol.0 (144217) Sun Elevation: 14° 2023-04-04 18:25:02.037 - debug: shuttercontrol.0 (144217) Buero level conversion is disabled ... 2023-04-04 18:25:02.037 - debug: shuttercontrol.0 (144217) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-04 18:25:02.040 - debug: shuttercontrol.0 (144217) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-04 18:26:07.826 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3767 2023-04-04 18:26:17.827 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:27:02.046 - debug: shuttercontrol.0 (144217) Buero level conversion is disabled ... 2023-04-04 18:27:02.047 - debug: shuttercontrol.0 (144217) start pendingAlarm to check if an alarm is currently pending (exept frost) 2023-04-04 18:27:02.052 - debug: shuttercontrol.0 (144217) status alarm pending for mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos: false 2023-04-04 18:28:49.380 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3737 2023-04-04 18:28:59.380 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:30:00.009 - debug: shuttercontrol.0 (144217) calculate astrodata ... 2023-04-04 18:30:00.010 - debug: shuttercontrol.0 (144217) Sun Azimut: 262.2° 2023-04-04 18:30:00.010 - debug: shuttercontrol.0 (144217) Sun Elevation: 13.2° 2023-04-04 18:31:16.376 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3700 2023-04-04 18:31:26.377 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:33:28.866 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3678 2023-04-04 18:33:38.869 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:35:00.009 - debug: shuttercontrol.0 (144217) calculate astrodata ... 2023-04-04 18:35:00.009 - debug: shuttercontrol.0 (144217) Sun Azimut: 263.2° 2023-04-04 18:35:00.010 - debug: shuttercontrol.0 (144217) Sun Elevation: 12.5° 2023-04-04 18:36:31.161 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3602 2023-04-04 18:36:41.163 - debug: shuttercontrol.0 (144217) Brightness State Down is: false 2023-04-04 18:39:18.867 - debug: shuttercontrol.0 (144217) Brightness sensor value: 3590 2023-04-04 18:39:28.868 - debug: shuttercontrol.0 (144217) Brightness State Down is: falseKannst Du bitte noch mal schauen? Welche Daten brauchst Du?
Vielen Dank..... -
@stealthangel Stelle mal in den Rollladen Einstellungen die Automatik auch bei geöffneten Fenster ein.
Passt der Wert 0 für den Fensterkontakt?
-
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel Stelle mal in den Rollladen Einstellungen die Automatik auch bei geöffneten Fenster ein.
Passt der Wert 0 für den Fensterkontakt?
Ich denke, das passt.
Ich habe jetzt in den Sourcecode mal ein paar Debugs eingebaut.
In die if Bedingung
if ((currentValue === mustValue || currentValue === mustValueTilted) && shutterSettings[s].tempSensor != '' || (currentValue != mustValue && currentValue != mustValueTilted && shutterSettings[s].autoDrive != 'onlyDown' && shutterSettings[s].autoDrive != 'off') || (shutterSettings[s].triggerID == '')) { .......springt er schon nicht mehr rein.
Die Objekte sind
CurrentValue: 0 mustValue: 0 mustValueTilted: 0 shutterSettungs.temp: shutterSettings[s].autoDrive: upDown shutterSettings[s].triggerID: hm-rpc.1.00155D898A87A1.1.STATE shutterSettings[s].driveAfterClose: falseMit meinen stümperhaften Programmierkenntnissen würde ich sagen es liegt an
shutterSettings[s].tempSensor != ''Aber ich habe keinen Temperatursensor
Was kann ich da tun?
Danke für Eure Hilfe.... -
Mahlzeit und Frohe Ostern zusammen. Da einige Shelly's 2,5 bei mir defekt waren, habe ich heute neue Shelly's 2PM verbaut. Jetzt wollte ich gerade im ShutterControl Adapter die neuen Shellys hinzufügen und sehe, dass es den Reiter Position nicht mehr gibt? Kann mir jemand weiterhelfen und sagen wie ich bei den neuen Shelly's 2PM auf Positon fahren kann?
-
@tolkin said in Einstellungen von Shuttercontrol:
....sagen wie ich bei den neuen Shelly's 2PM auf Positon fahren kann?
Schau mal hier:
Shelly Gen 2 Device APIund hier:
MQTT ControlBei weiteren Fragen besser ein neues Thema aufmachen, das es nix mit den Shuttercontrol Adapter zu tun hat....
-
@stealthangel sagte in Einstellungen von Shuttercontrol:
Aber ich habe keinen Temperatursensor
Trage doch mal zum testen irgendeine ID bei tempSensor ein.
Damit könnte man den Fehler erstmal eingrenzen -
@stealthangel Teste bitte mal die v1.4.24 ... Da sollte es egal sein, ob du einen Temperatursensor hast
-
@simatec said in Einstellungen von Shuttercontrol:
Damit könnte man den Fehler erstmal eingrenzen
Ich habe vermutlich den Fehler gefunden
Mit Temp-Sensor geht es.Das ist aber gar nicht nötig. In der "sunProtect.js" ist in ca. Zeile 1251 steht die if-Bedingung
if ((currentValue === mustValue || currentValue === mustValueTilted) && shutterSettings[s].tempSensor != '' || (currentValue != mustValue && currentValue != mustValueTilted && shutterSettings[s].autoDrive != 'onlyDown' && shutterSettings[s].autoDrive != 'off') || (shutterSettings[s].triggerID == '')) {In der ganzen if-Bedingung wird "shutterSettings[].tempSensor" aber nicht gebraucht.
Aus meiner Sicht müsste&& shutterSettings[].tempSensor != ''ersatzlos gelöscht werden. Habe ich auch ausprobiert. Damit klappt es.
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel Teste bitte mal die v1.4.24 ... Da sollte es egal sein, ob du einen Temperatursensor hast
Lade ich gleich mal und Teste....
Danke für Eure Hilfe
-
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel Teste bitte mal die v1.4.24 ... Da sollte es egal sein, ob du einen Temperatursensor hast
Jau, damit klappt es. Super, danke.
Allerdings war es jetzt so, dass als sunProtect bei 210° Azimut gestartet wurde ist der Rollladen 3x innerhalb von wenigen Minuten runter und rauf gefahren
2023-04-11 14:55:02.018 - info: shuttercontrol.0 (175760) Sunprotect #416 Set ID: Buero value: 30% 2023-04-11 14:55:02.037 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-11 14:55:29.544 - info: shuttercontrol.0 (175760) Lightsensor #5 Set ID: Buero value: 100% 2023-04-11 14:55:29.552 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-11 14:55:31.535 - info: shuttercontrol.0 (175760) Sunprotect #416 Set ID: Buero value: 30% 2023-04-11 14:55:31.542 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-11 14:57:59.509 - info: shuttercontrol.0 (175760) Lightsensor #5 Set ID: Buero value: 100% 2023-04-11 14:57:59.519 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-11 14:58:01.499 - info: shuttercontrol.0 (175760) Sunprotect #416 Set ID: Buero value: 30% 2023-04-11 14:58:01.505 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos]Das war mit der Version davor nicht. (Obwohl ich gestehen muss, das heute noch zusätzlich "autoDown auf false gesetzt war).
Eine Idee dazu?....
-
@stealthangel was sagt der Debuglog?
-
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel was sagt der Debuglog?
2023-04-12 14:50:00.010 - debug: shuttercontrol.0 (179737) calculate astrodata ... 2023-04-12 14:50:00.010 - debug: shuttercontrol.0 (179737) Sun Azimut: 209.5° 2023-04-12 14:50:00.011 - debug: shuttercontrol.0 (179737) Sun Elevation: 43.3° 2023-04-12 14:50:09.334 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 14:52:53.560 - debug: shuttercontrol.0 (179737) Brightness sensor value: 4125 2023-04-12 14:52:53.608 - debug: shuttercontrol.0 (179737) Lightsensor up Buero already up at: 100% - setting current action: up 2023-04-12 14:53:03.561 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 14:55:00.007 - debug: shuttercontrol.0 (179737) calculate astrodata ... 2023-04-12 14:55:00.008 - debug: shuttercontrol.0 (179737) Sun Azimut: 211.1° 2023-04-12 14:55:00.008 - debug: shuttercontrol.0 (179737) Sun Elevation: 42.9° 2023-04-12 14:55:02.018 - debug: shuttercontrol.0 (179737) Buero: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-12 14:55:02.019 - info: shuttercontrol.0 (179737) Sunprotect #416 Set ID: Buero value: 30% 2023-04-12 14:55:02.070 - debug: shuttercontrol.0 (179737) #0 wait for shutter check started 2023-04-12 14:55:02.069 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-12 14:55:02.099 - debug: shuttercontrol.0 (179737) Sunprotect for Buero is active 2023-04-12 14:55:02.100 - debug: shuttercontrol.0 (179737) RangeMinus: 210 < 211.1RangePlus: 320 > 211.1 2023-04-12 14:55:02.100 - debug: shuttercontrol.0 (179737) last automatic Action for Buero: down_Sunprotect 2023-04-12 14:55:02.101 - debug: shuttercontrol.0 (179737) Sunprotect Buero old height: 100% new height: 30% 2023-04-12 14:55:22.072 - debug: shuttercontrol.0 (179737) #0 wait for shutter check end 2023-04-12 14:55:22.074 - debug: shuttercontrol.0 (179737) Shutter state changed: Buero old value = 100 new value = 30 2023-04-12 14:55:22.074 - debug: shuttercontrol.0 (179737) #1 shutterName: Buero 2023-04-12 14:55:22.074 - debug: shuttercontrol.0 (179737) #1 shutterState: 30 % 2023-04-12 14:55:22.074 - debug: shuttercontrol.0 (179737) #1 currentAction: Manu_Mode 2023-04-12 14:55:22.075 - debug: shuttercontrol.0 (179737) #1 triggerAction: Manu_Mode 2023-04-12 14:55:22.075 - debug: shuttercontrol.0 (179737) #1 currentHeight: 30 % 2023-04-12 14:55:22.075 - debug: shuttercontrol.0 (179737) #1 oldHeight: 100 % 2023-04-12 14:55:22.075 - debug: shuttercontrol.0 (179737) #1 currentShutterState: activated 2023-04-12 14:55:22.076 - debug: shuttercontrol.0 (179737) #1 currentShutterStateTime: 20 seconds 2023-04-12 14:55:22.127 - debug: shuttercontrol.0 (179737) Buero drived manually to 30. Old value = 100. New value = 30 2023-04-12 14:55:22.127 - debug: shuttercontrol.0 (179737) Buero Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-12 14:55:33.323 - debug: shuttercontrol.0 (179737) Brightness sensor value: 4104 2023-04-12 14:55:33.354 - info: shuttercontrol.0 (179737) Lightsensor #5 Set ID: Buero value: 100% 2023-04-12 14:55:33.361 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-12 14:55:33.362 - debug: shuttercontrol.0 (179737) #0 wait for shutter check started 2023-04-12 14:55:33.419 - debug: shuttercontrol.0 (179737) last automatic Action for Buero: up_Brightness 2023-04-12 14:55:33.420 - debug: shuttercontrol.0 (179737) save current height: 100% from Buero 2023-04-12 14:55:43.325 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 14:55:53.364 - debug: shuttercontrol.0 (179737) #0 wait for shutter check end 2023-04-12 14:55:53.365 - debug: shuttercontrol.0 (179737) Buero Old value = 100. New value = 100. automatic is active 2023-04-12 14:57:58.575 - debug: shuttercontrol.0 (179737) Brightness sensor value: 3967 2023-04-12 14:57:58.629 - debug: shuttercontrol.0 (179737) Lightsensor up Buero already up at: 100% - setting current action: up 2023-04-12 14:58:08.577 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 15:00:00.008 - debug: shuttercontrol.0 (179737) calculate astrodata ... 2023-04-12 15:00:00.008 - debug: shuttercontrol.0 (179737) Sun Azimut: 212.7° 2023-04-12 15:00:00.009 - debug: shuttercontrol.0 (179737) Sun Elevation: 42.5° 2023-04-12 15:00:02.020 - debug: shuttercontrol.0 (179737) Buero: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-12 15:00:02.020 - info: shuttercontrol.0 (179737) Sunprotect #416 Set ID: Buero value: 30% 2023-04-12 15:00:02.065 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-12 15:00:02.066 - debug: shuttercontrol.0 (179737) #0 wait for shutter check started 2023-04-12 15:00:02.121 - debug: shuttercontrol.0 (179737) Sunprotect for Buero is active 2023-04-12 15:00:02.121 - debug: shuttercontrol.0 (179737) RangeMinus: 210 < 212.7RangePlus: 320 > 212.7 2023-04-12 15:00:02.121 - debug: shuttercontrol.0 (179737) last automatic Action for Buero: down_Sunprotect 2023-04-12 15:00:02.121 - debug: shuttercontrol.0 (179737) Sunprotect Buero old height: 100% new height: 30% 2023-04-12 15:00:09.576 - debug: shuttercontrol.0 (179737) Brightness sensor value: 3856 2023-04-12 15:00:09.606 - debug: shuttercontrol.0 (179737) outsidetemperature changed: hm-rpc.1.00181D89B4E7B4.1.ACTUAL_TEMPERATURE Value: 10.6 2023-04-12 15:00:09.672 - debug: shuttercontrol.0 (179737) Lightsensor up Buero already up at: 100% - setting current action: sunProtect 2023-04-12 15:00:19.577 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 15:00:22.067 - debug: shuttercontrol.0 (179737) #0 wait for shutter check end 2023-04-12 15:00:22.068 - debug: shuttercontrol.0 (179737) Shutter state changed: Buero old value = 100 new value = 30 2023-04-12 15:00:22.069 - debug: shuttercontrol.0 (179737) Buero Old value = 100. New value = 30. automatic is active 2023-04-12 15:03:10.046 - debug: shuttercontrol.0 (179737) Brightness sensor value: 4257 2023-04-12 15:03:10.068 - debug: shuttercontrol.0 (179737) outsidetemperature changed: hm-rpc.1.00181D89B4E7B4.1.ACTUAL_TEMPERATURE Value: 10.5 2023-04-12 15:03:10.130 - debug: shuttercontrol.0 (179737) Lightsensor up Buero already up at: 100% - setting current action: sunProtect 2023-04-12 15:03:20.047 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 15:05:00.008 - debug: shuttercontrol.0 (179737) calculate astrodata ... 2023-04-12 15:05:00.009 - debug: shuttercontrol.0 (179737) Sun Azimut: 214.3° 2023-04-12 15:05:00.009 - debug: shuttercontrol.0 (179737) Sun Elevation: 42.1° 2023-04-12 15:05:56.040 - debug: shuttercontrol.0 (179737) Brightness sensor value: 4471 2023-04-12 15:05:56.083 - debug: shuttercontrol.0 (179737) Lightsensor up Buero already up at: 100% - setting current action: sunProtect 2023-04-12 15:06:06.041 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 15:08:27.812 - debug: shuttercontrol.0 (179737) Brightness sensor value: 4399 2023-04-12 15:08:27.839 - debug: shuttercontrol.0 (179737) outsidetemperature changed: hm-rpc.1.00181D89B4E7B4.1.ACTUAL_TEMPERATURE Value: 10.6 2023-04-12 15:08:27.898 - debug: shuttercontrol.0 (179737) Lightsensor up Buero already up at: 100% - setting current action: sunProtect 2023-04-12 15:08:37.813 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 15:10:00.014 - debug: shuttercontrol.0 (179737) calculate astrodata ... 2023-04-12 15:10:00.014 - debug: shuttercontrol.0 (179737) Sun Azimut: 215.8° 2023-04-12 15:10:00.015 - debug: shuttercontrol.0 (179737) Sun Elevation: 41.6° 2023-04-12 15:10:45.049 - debug: shuttercontrol.0 (179737) Brightness sensor value: 4524 2023-04-12 15:10:45.135 - debug: shuttercontrol.0 (179737) Lightsensor up Buero already up at: 100% - setting current action: sunProtect 2023-04-12 15:10:55.050 - debug: shuttercontrol.0 (179737) Brightness State Down is: false 2023-04-12 15:12:47.794 - debug: shuttercontrol.0 (179737) Brightness sensor value: 4369 2023-04-12 15:12:47.834 - debug: shuttercontrol.0 (179737) Lightsensor up Buero already up at: 100% - setting current action: sunProtect 2023-04-12 15:12:57.795 - debug: shuttercontrol.0 (179737) Brightness State Down is: falseDanke für Deine Hilfe...
-
@stealthangel Deine Überprüfung der Rollläden nach 20 Sekunden löst hier die Aktion aus.
Entweder deine Rollläden liefern einen sauberen State, dann schalte die Überprüfung aus oder setze der Wert höher.
Z.B. auf 60 oder 100 Sekunden -
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel Deine Überprüfung der Rollläden nach 20 Sekunden löst hier die Aktion aus.
Entweder deine Rollläden liefern einen sauberen State, dann schalte die Überprüfung aus oder setze der Wert höher.
Z.B. auf 60 oder 100 SekundenHallo, die Überprüfung ist auf 60 Sekunden eingestellt
Jetzt war ich zwar nicht zuhause, aber als ich nach Hause kam war der Rollladen hochgefahren (und nicht auf 30%).
2023-04-13 14:50:00.007 - debug: shuttercontrol.0 (184934) calculate astrodata ... 2023-04-13 14:50:00.008 - debug: shuttercontrol.0 (184934) Sun Azimut: 209.7° 2023-04-13 14:50:00.008 - debug: shuttercontrol.0 (184934) Sun Elevation: 43.6° 2023-04-13 14:50:04.184 - debug: shuttercontrol.0 (184934) Brightness sensor value: 7487 2023-04-13 14:50:04.208 - debug: shuttercontrol.0 (184934) outsidetemperature changed: hm-rpc.1.00181D89B4E7B4.1.ACTUAL_TEMPERATURE Value: 12 2023-04-13 14:50:04.274 - debug: shuttercontrol.0 (184934) Lightsensor up Buero already up at: 100% - setting current action: up 2023-04-13 14:50:14.184 - debug: shuttercontrol.0 (184934) Brightness State Down is: false 2023-04-13 14:52:53.676 - debug: shuttercontrol.0 (184934) Brightness sensor value: 7333 2023-04-13 14:52:53.718 - debug: shuttercontrol.0 (184934) Lightsensor up Buero already up at: 100% - setting current action: up 2023-04-13 14:53:03.677 - debug: shuttercontrol.0 (184934) Brightness State Down is: false 2023-04-13 14:55:00.009 - debug: shuttercontrol.0 (184934) calculate astrodata ... 2023-04-13 14:55:00.009 - debug: shuttercontrol.0 (184934) Sun Azimut: 211.4° 2023-04-13 14:55:00.010 - debug: shuttercontrol.0 (184934) Sun Elevation: 43.2° 2023-04-13 14:55:02.023 - debug: shuttercontrol.0 (184934) Buero: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-13 14:55:02.024 - info: shuttercontrol.0 (184934) Sunprotect #416 Set ID: Buero value: 30% 2023-04-13 14:55:02.075 - debug: shuttercontrol.0 (184934) #0 wait for shutter check started 2023-04-13 14:55:02.073 - info: mqtt.0 (955) send2Server mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos[shellies/Buero/Rolladen/roller/0/command/pos] 2023-04-13 14:55:02.126 - debug: shuttercontrol.0 (184934) Sunprotect for Buero is active 2023-04-13 14:55:02.127 - debug: shuttercontrol.0 (184934) RangeMinus: 210 < 211.4RangePlus: 320 > 211.4 2023-04-13 14:55:02.127 - debug: shuttercontrol.0 (184934) last automatic Action for Buero: down_Sunprotect 2023-04-13 14:55:02.127 - debug: shuttercontrol.0 (184934) Sunprotect Buero old height: 100% new height: 30% 2023-04-13 14:55:28.929 - debug: shuttercontrol.0 (184934) Brightness sensor value: 7345 2023-04-13 14:55:28.952 - debug: shuttercontrol.0 (184934) outsidetemperature changed: hm-rpc.1.00181D89B4E7B4.1.ACTUAL_TEMPERATURE Value: 12.1 2023-04-13 14:55:29.030 - debug: shuttercontrol.0 (184934) Lightsensor up Buero already up at: 100% - setting current action: sunProtect 2023-04-13 14:55:38.930 - debug: shuttercontrol.0 (184934) Brightness State Down is: false 2023-04-13 14:56:02.076 - debug: shuttercontrol.0 (184934) #0 wait for shutter check end 2023-04-13 14:56:02.078 - debug: shuttercontrol.0 (184934) Shutter state changed: Buero old value = 100 new value = 30 2023-04-13 14:56:02.078 - debug: shuttercontrol.0 (184934) Buero Old value = 100. New value = 30. automatic is active 2023-04-13 14:57:49.676 - debug: shuttercontrol.0 (184934) Brightness sensor value: 7125 2023-04-13 14:57:49.724 - debug: shuttercontrol.0 (184934) Lightsensor up Buero already up at: 100% - setting current action: sunProtect 2023-04-13 14:57:59.677 - debug: shuttercontrol.0 (184934) Brightness State Down is: false 2023-04-13 14:59:55.972 - debug: shuttercontrol.0 (184934) Brightness sensor value: 6848 2023-04-13 14:59:56.003 - debug: shuttercontrol.0 (184934) outsidetemperature changed: hm-rpc.1.00181D89B4E7B4.1.ACTUAL_TEMPERATURE Value: 12.2 2023-04-13 14:59:56.029 - debug: shuttercontrol.0 (184934) Lightsensor up Buero already up at: 100% - setting current action: sunProtectDie Objects sind der Meinung, dass der Rollladen auf 30% steht
In Wirklichkeit ist der Rollladen aber auf 100%
Also ist er scheinbar runter und gleich wieder hochgefahren.
Kast Du bitte nochmal schauen, was hier schief gegangen ist?..... -
Halt Stop, ich habe noch einen Fehler bei mir gefunden. Wenn ich die "Objekt-ID Rollladen" einstelle wird vermutlich die Sollposition dort hin gesendet und die Position davon auch abgefragt, oder?
Bei meinen Shellys muss ich aber auf
mqtt.0.shellies.Buero.Rolladen.roller.0.command.posschreiben und von
mqtt.0.shellies.Buero.Rolladen.roller.0.poslesen. Ich hatte als Object-ID "mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos". Das könnte der Fehler sein. Ich arbeite jetzt mit einen Alias.
"alias": { "id": { "read": "mqtt.0.shellies.Buero.Rolladen.roller.0.pos", "write": "mqtt.0.shellies.Buero.Rolladen.roller.0.command.pos" } },Ich hoffe, dass es jetzt morgen funktioniert.
Erstmal Sorry und vielen Dank....
-
@stealthangel Laut dem Log hat Shuttercontrol mit dem Überprüfen nach 60 Sekunden alles richtig gemacht.
Automatik wurde erkannt und er wurde in den Sonnenschutz gefahren.Ich gehe mal davon aus, dass da bei deinen States der Rollläden was krum ist.
Hast du da noch irgendwelche Scripte laufen?Wann wurde denn der State des Rollladens geändert?
-
@stealthangel Warum nutzt du nicht den Shelly Adapter??? Würde sicher einiges erleichtern
-
@simatec said in Einstellungen von Shuttercontrol:
@stealthangel Warum nutzt du nicht den Shelly Adapter??? Würde sicher einiges erleichtern
Ich habe jetzt auch auf den Shelly Adapter umgestellt. Das Problem ist aber immer noch das Gleiche
Der Rollladen ist wieder 3 mal runter und rauf gefahren. So langsam verzweifele ich ....
2023-04-17 14:45:00.014 - debug: shuttercontrol.0 (207218) calculate astrodata ... 2023-04-17 14:45:00.014 - debug: shuttercontrol.0 (207218) Sun Azimut: 209° 2023-04-17 14:45:00.015 - debug: shuttercontrol.0 (207218) Sun Elevation: 45.3° 2023-04-17 14:46:12.976 - debug: shuttercontrol.0 (207218) Brightness sensor value: 5032 2023-04-17 14:46:14.052 - debug: shuttercontrol.0 (207218) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-17 14:46:22.978 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:48:53.703 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4799 2023-04-17 14:48:54.799 - debug: shuttercontrol.0 (207218) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-17 14:49:03.703 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:50:00.019 - debug: shuttercontrol.0 (207218) calculate astrodata ... 2023-04-17 14:50:00.020 - debug: shuttercontrol.0 (207218) Sun Azimut: 210.7° 2023-04-17 14:50:00.021 - debug: shuttercontrol.0 (207218) Sun Elevation: 44.9° 2023-04-17 14:50:02.035 - debug: shuttercontrol.0 (207218) BueroRollladen: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-17 14:50:02.036 - info: shuttercontrol.0 (207218) Sunprotect #416 Set ID: BueroRollladen value: 30% 2023-04-17 14:50:02.048 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:50:02.059 - debug: shuttercontrol.0 (207218) Sunprotect for BueroRollladen is active 2023-04-17 14:50:02.060 - debug: shuttercontrol.0 (207218) RangeMinus: 210 < 210.7RangePlus: 320 > 210.7 2023-04-17 14:50:02.060 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: down_Sunprotect 2023-04-17 14:50:02.060 - debug: shuttercontrol.0 (207218) Sunprotect BueroRollladen old height: % new height: 30% 2023-04-17 14:50:02.083 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:50:14.335 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:51:02.049 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:51:02.051 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 30 2023-04-17 14:51:02.051 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:51:02.052 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:51:02.052 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:51:02.052 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:51:02.053 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:51:02.053 - debug: shuttercontrol.0 (207218) #1 oldHeight: % 2023-04-17 14:51:02.053 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:51:02.053 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:51:02.084 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:51:02.085 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 30 2023-04-17 14:51:02.086 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:51:02.087 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:51:02.087 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:51:02.087 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:51:02.088 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:51:02.088 - debug: shuttercontrol.0 (207218) #1 oldHeight: % 2023-04-17 14:51:02.089 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:51:02.089 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:51:02.091 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = . New value = 30 2023-04-17 14:51:02.092 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:51:02.142 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = . New value = 30 2023-04-17 14:51:02.143 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:51:14.336 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:51:14.338 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 30 2023-04-17 14:51:14.338 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:51:14.339 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:51:14.339 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:51:14.339 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:51:14.339 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:51:14.340 - debug: shuttercontrol.0 (207218) #1 oldHeight: % 2023-04-17 14:51:14.340 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:51:14.340 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:51:14.390 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = . New value = 30 2023-04-17 14:51:14.391 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:51:19.961 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4622 2023-04-17 14:51:19.995 - info: shuttercontrol.0 (207218) Lightsensor #5 Set ID: BueroRollladen value: 100% 2023-04-17 14:51:20.003 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:51:20.013 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: up_Brightness 2023-04-17 14:51:20.013 - debug: shuttercontrol.0 (207218) save current height: 100% from BueroRollladen 2023-04-17 14:51:20.035 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:51:29.963 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:51:33.042 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:52:20.004 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:52:20.005 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 100 2023-04-17 14:52:20.006 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = . New value = 100. automatic is active 2023-04-17 14:52:20.035 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:52:20.037 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 100 2023-04-17 14:52:20.038 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = . New value = 100. automatic is active 2023-04-17 14:52:33.043 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:52:33.044 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = new value = 100 2023-04-17 14:52:33.045 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = . New value = 100. automatic is active 2023-04-17 14:53:31.713 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4502 2023-04-17 14:53:31.770 - debug: shuttercontrol.0 (207218) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-17 14:53:41.714 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:55:00.017 - debug: shuttercontrol.0 (207218) calculate astrodata ... 2023-04-17 14:55:00.018 - debug: shuttercontrol.0 (207218) Sun Azimut: 212.3° 2023-04-17 14:55:00.018 - debug: shuttercontrol.0 (207218) Sun Elevation: 44.5° 2023-04-17 14:55:02.040 - debug: shuttercontrol.0 (207218) BueroRollladen: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-17 14:55:02.041 - info: shuttercontrol.0 (207218) Sunprotect #416 Set ID: BueroRollladen value: 30% 2023-04-17 14:55:02.093 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:55:02.111 - debug: shuttercontrol.0 (207218) Sunprotect for BueroRollladen is active 2023-04-17 14:55:02.112 - debug: shuttercontrol.0 (207218) RangeMinus: 210 < 212.3RangePlus: 320 > 212.3 2023-04-17 14:55:02.113 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: down_Sunprotect 2023-04-17 14:55:02.113 - debug: shuttercontrol.0 (207218) Sunprotect BueroRollladen old height: 100% new height: 30% 2023-04-17 14:55:02.136 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:55:14.373 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:56:02.095 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:56:02.097 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 14:56:02.098 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:56:02.099 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:56:02.099 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:56:02.100 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:56:02.100 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:56:02.101 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 14:56:02.101 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:56:02.101 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:56:02.137 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:56:02.143 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 14:56:02.144 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:56:02.144 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:56:02.145 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:56:02.146 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:56:02.146 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:56:02.147 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 14:56:02.147 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:56:02.148 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:56:02.152 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 14:56:02.153 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:56:02.208 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 14:56:02.209 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:56:14.374 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:56:14.377 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 14:56:14.377 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 14:56:14.378 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 14:56:14.378 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 14:56:14.378 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 14:56:14.378 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 14:56:14.379 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 14:56:14.379 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 14:56:14.379 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 14:56:14.432 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 14:56:14.432 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 14:56:32.952 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4650 2023-04-17 14:56:32.992 - info: shuttercontrol.0 (207218) Lightsensor #5 Set ID: BueroRollladen value: 100% 2023-04-17 14:56:33.000 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:56:33.010 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: up_Brightness 2023-04-17 14:56:33.011 - debug: shuttercontrol.0 (207218) save current height: 100% from BueroRollladen 2023-04-17 14:56:33.032 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:56:42.953 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 14:56:46.052 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 14:57:26.778 - info: admin.0 (831) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-17 14:57:33.002 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:57:33.003 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = 100. New value = 100. automatic is active 2023-04-17 14:57:33.032 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:57:33.034 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = 100. New value = 100. automatic is active 2023-04-17 14:57:38.475 - info: admin.0 (831) ==> Connected system.user.admin from ::ffff:192.168.2.21 2023-04-17 14:57:46.054 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 14:57:46.055 - debug: shuttercontrol.0 (207218) BueroRollladen Old value = 100. New value = 100. automatic is active 2023-04-17 14:59:19.969 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4804 2023-04-17 14:59:20.020 - debug: shuttercontrol.0 (207218) Lightsensor up BueroRollladen already up at: 100% - setting current action: up 2023-04-17 14:59:29.971 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 15:00:00.012 - debug: shuttercontrol.0 (207218) calculate astrodata ... 2023-04-17 15:00:00.013 - debug: shuttercontrol.0 (207218) Sun Azimut: 213.9° 2023-04-17 15:00:00.013 - debug: shuttercontrol.0 (207218) Sun Elevation: 44.1° 2023-04-17 15:00:02.026 - debug: shuttercontrol.0 (207218) BueroRollladen: Check basis for sunprotect. Height:100 > HeightDownSun: 30 AND Height:100 == currentHeight:100 AND currentHeight:100 == heightUp:100 2023-04-17 15:00:02.026 - info: shuttercontrol.0 (207218) Sunprotect #416 Set ID: BueroRollladen value: 30% 2023-04-17 15:00:02.075 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:00:02.086 - debug: shuttercontrol.0 (207218) Sunprotect for BueroRollladen is active 2023-04-17 15:00:02.086 - debug: shuttercontrol.0 (207218) RangeMinus: 210 < 213.9RangePlus: 320 > 213.9 2023-04-17 15:00:02.086 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: down_Sunprotect 2023-04-17 15:00:02.087 - debug: shuttercontrol.0 (207218) Sunprotect BueroRollladen old height: 100% new height: 30% 2023-04-17 15:00:02.105 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:00:14.359 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:01:02.077 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 15:01:02.078 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 15:01:02.079 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 15:01:02.079 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 15:01:02.080 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 15:01:02.080 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 15:01:02.080 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 15:01:02.080 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 15:01:02.081 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 15:01:02.081 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 15:01:02.106 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 15:01:02.128 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 15:01:02.128 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 15:01:02.129 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 15:01:02.130 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 15:01:02.130 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 15:01:02.132 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 15:01:02.132 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 15:01:02.132 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 15:01:02.133 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 15:01:02.140 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 15:01:02.140 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 15:01:02.188 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 15:01:02.188 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 15:01:14.360 - debug: shuttercontrol.0 (207218) #0 wait for shutter check end 2023-04-17 15:01:14.361 - debug: shuttercontrol.0 (207218) Shutter state changed: BueroRollladen old value = 100 new value = 30 2023-04-17 15:01:14.362 - debug: shuttercontrol.0 (207218) #1 shutterName: BueroRollladen 2023-04-17 15:01:14.362 - debug: shuttercontrol.0 (207218) #1 shutterState: 30 % 2023-04-17 15:01:14.362 - debug: shuttercontrol.0 (207218) #1 currentAction: Manu_Mode 2023-04-17 15:01:14.363 - debug: shuttercontrol.0 (207218) #1 triggerAction: Manu_Mode 2023-04-17 15:01:14.363 - debug: shuttercontrol.0 (207218) #1 currentHeight: 30 % 2023-04-17 15:01:14.363 - debug: shuttercontrol.0 (207218) #1 oldHeight: 100 % 2023-04-17 15:01:14.363 - debug: shuttercontrol.0 (207218) #1 currentShutterState: activated 2023-04-17 15:01:14.364 - debug: shuttercontrol.0 (207218) #1 currentShutterStateTime: 60 seconds 2023-04-17 15:01:14.415 - debug: shuttercontrol.0 (207218) BueroRollladen drived manually to 30. Old value = 100. New value = 30 2023-04-17 15:01:14.415 - debug: shuttercontrol.0 (207218) BueroRollladen Updated trigger action to Manu_Mode to prevent moving after window close 2023-04-17 15:01:52.457 - debug: shuttercontrol.0 (207218) Brightness sensor value: 4873 2023-04-17 15:01:52.494 - info: shuttercontrol.0 (207218) Lightsensor #5 Set ID: BueroRollladen value: 100% 2023-04-17 15:01:52.506 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:01:52.520 - debug: shuttercontrol.0 (207218) last automatic Action for BueroRollladen: up_Brightness 2023-04-17 15:01:52.520 - debug: shuttercontrol.0 (207218) save current height: 100% from BueroRollladen 2023-04-17 15:01:52.537 - debug: shuttercontrol.0 (207218) #0 wait for shutter check started 2023-04-17 15:02:02.459 - debug: shuttercontrol.0 (207218) Brightness State Down is: false 2023-04-17 15:02:05.565 - debug: shuttercontrol.0 (207218) #0 wait for shutter check startedAlso irgendwas läuft noch falsch.
Mich wundert, dass sich der Status ändert. Ist das so richtig?Screenshot ist von einem etwas späteren Zeitpunkt, war aber sonst auch so, allerdings nicht geloggt....
Jetzt wo ich hier schreibe, fährt der Rollladen munter weiter rauf und runter.
Es ist mit dem Shelly-Adapter also massiv schlechter geworden
