Gosund SP111 mit Tasmota 13.2.0 Problem mit DP

Ralla66

was bastelst du da :-)

sp 111 14112023.jpg

RalfTh

@ralla66 So, habe jetzt alles so eingestellt wie du es mir in den Bildern gezeigt hast. Habe vorher den Adapter gestoppt und die Objekte gelöscht.
Das Script ist nicht aktiviert.
Instanz gestartet, die Objekte werden angelegt.
Di DP's welche mit "ENERGY_" beginnen werden,wenn überhaupt nur nach einer Ewigkeit aktualisiert und das obwohl die Message ankam. Hier Auszug aus der Konsole:

B8D3E7/POWER = ON
07:14:16.291 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:14:16","Uptime":"0T00:36:54","UptimeSec":2214,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":58,"Signal":-71,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:14:16.302 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:14:16","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.527,"Yesterday":0.170,"Today":0.026,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.183}}
07:14:46.290 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:14:46","Uptime":"0T00:37:24","UptimeSec":2244,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:14:46.299 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:14:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.528,"Yesterday":0.170,"Today":0.027,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.183}}
07:15:16.280 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:15:16","Uptime":"0T00:37:54","UptimeSec":2274,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:15:16.293 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:15:16","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.528,"Yesterday":0.170,"Today":0.027,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.183}}
07:15:46.251 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:15:46","Uptime":"0T00:38:24","UptimeSec":2304,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":64,"Signal":-68,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:15:46.262 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:15:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.528,"Yesterday":0.170,"Today":0.027,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.186}}
07:16:16.257 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:16:16","Uptime":"0T00:38:54","UptimeSec":2334,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":20,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:16:16.267 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:16:16","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.529,"Yesterday":0.170,"Today":0.028,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.185}}
07:16:46.256 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:16:46","Uptime":"0T00:39:24","UptimeSec":2364,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:16:46.268 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:16:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.529,"Yesterday":0.170,"Today":0.028,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.186}}
07:17:16.261 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:17:16","Uptime":"0T00:39:54","UptimeSec":2394,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":60,"Signal":-70,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:17:16.273 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:17:16","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.530,"Yesterday":0.170,"Today":0.029,"Period":0,"Power":44,"ApparentPower":44,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.188}}
07:17:46.275 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:17:46","Uptime":"0T00:40:24","UptimeSec":2424,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:17:46.285 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:17:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.530,"Yesterday":0.170,"Today":0.029,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.185}}

Derweil im ioBroker:

Und das, obwohl laut LOG auch hier die Informationen eintrudeln:

Ich habe die Steckdose mittlerweile drei mal geflasht und jedesmal eine andere Konfiguration verwendet. Ich denke, ein erneutes flashen bringt da auch nicht die Lösung. Falls keine anderen Ideen mehr da sind werde ich mir einen anderen MQTT-Broker suchen und das JSON aufdröseln.

Ralla66

@ralfth

alle print des Scriptes werden in der Console nicht ausgegeben, bedeutet dein Script läuft nicht.
Topic ist noch Reserve2 und nicht default.
Ob deine .bin überhaupt in Ordnung ist weiß keiner.
Daher das compilieren mit Tasmocompiler. Das ist halt viel einfacher.

Solange die Topic / Full Topic nicht in Ordnung sind und das Script nicht läuft kann
ich auch nicht weiter helfen. Da es ja bei mir läuft liegt das ja an deinem System.

RalfTh

@ralla66 sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

alle print des Scriptes werden in der Console nicht ausgegeben, bedeutet dein Script läuft nicht.

Hatte ich auch geschrieben, dass das Script nicht aktiviert ist.

Meine .bin habe ich mit Gitpod kompiliert (Quelle: https://github.com/arendst/Tasmota) und alle von dir genannten Defines, soweit in my_user_config.h vorhanden, aktiviert. In einem Post weiter oben hatte ich das auch schon erwähnt.
Diese .bin habe ich dann auf den Gosund geflasht.

Das Script habe ich jetzt aktiviert und in der Konsole kommt folgende Fehlermeldung:

17:32:38.869 SCR: performs "websend [192.168.178.164] /cm?cmnd=status 10"
17:32:44.249 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}
17:32:44.257 MQT: stat/tasmota_B8D3E7/RESULT = {"Total":0}
17:32:44.264 MQT: stat/tasmota_B8D3E7/RESULT = {"Yesterday":0}
17:32:44.272 MQT: stat/tasmota_B8D3E7/RESULT = {"Today":0}
17:32:44.279 MQT: stat/tasmota_B8D3E7/RESULT = {"ApparentPower":0}
17:32:44.286 MQT: stat/tasmota_B8D3E7/RESULT = {"ReactivePower":0.00}
17:32:44.293 MQT: stat/tasmota_B8D3E7/RESULT = {"Power":0}
17:32:44.300 MQT: stat/tasmota_B8D3E7/RESULT = {"Voltage":0}
17:32:44.307 MQT: stat/tasmota_B8D3E7/RESULT = {"Current":0}
17:32:48.393 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T17:32:48","Uptime":"0T10:55:26","UptimeSec":39326,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":4,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":96,"Signal":-52,"LinkCount":1,"Downtime":"0T00:00:03"}}
17:32:48.406 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T17:32:48","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.544,"Yesterday":0.170,"Today":0.043,"Period":1,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":230,"Current":0.181}}
17:32:54.371 SCR: performs "websend [192.168.178.164] /cm?cmnd=status 10"
17:32:59.783 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}
17:32:59.792 MQT: stat/tasmota_B8D3E7/RESULT = {"Total":0}
17:32:59.799 MQT: stat/tasmota_B8D3E7/RESULT = {"Yesterday":0}
17:32:59.808 MQT: stat/tasmota_B8D3E7/RESULT = {"Today":0}
17:32:59.815 MQT: stat/tasmota_B8D3E7/RESULT = {"ApparentPower":0}
17:32:59.823 MQT: stat/tasmota_B8D3E7/RESULT = {"ReactivePower":0.00}

Die IP für das websend ist die des ioBroker oder der Gosund?

Hier noch mal mein Script:

>D
 
;a valid script must start with >D in the first line
 
 
Timer=0
 
WEBQ=5
 
VOL=0
CUR=0
POW=0
TOT=0
YES=0
TOD=0
APP=0
RAP=0
 
; Meins
 
; MQT: tasmota_Reserve2 = {"StatusSNS":{"Time":"2023-11-14T12:59:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.424,"Yesterday":0.007,"Today":0.093,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":231,"Current":0.181}}}
 
>BS
 
+>subscribe EA, cmnd/%topic%/Total
+>subscribe EA, cmnd/%topic%/Yesterday
+>subscribe EA, cmnd/%topic%/Today
+>subscribe EA, cmnd/%topic%/Power
+>subscribe EA, cmnd/%topic%/ApparentPower
+>subscribe EA, cmnd/%topic%/ReactivePower
+>subscribe EA, cmnd/%topic%/Power
+>subscribe EA, cmnd/%topic%/Voltage
+>subscribe EA, cmnd/%topic%/Current
 
>S
 
Timer+=1
 
;Executed every second 
 
 
if Timer>10
 
then
=>websend [192.168.178.164] /cm?cmnd=status 10
 
+>publish stat/%topic%/RESULT {"Total":%0TOT%}
+>publish stat/%topic%/RESULT {"Yesterday":%0YES%}
+>publish stat/%topic%/RESULT {"Today":%0TOD%}
+>publish stat/%topic%/RESULT {"ApparentPower":%0APP%}
+>publish stat/%topic%/RESULT {"ReactivePower":%RAP%}
+>publish stat/%topic%/RESULT {"Power":%0POW%}
+>publish stat/%topic%/RESULT {"Voltage":%0VOL%}
+>publish stat/%topic%/RESULT {"Current":%0CUR%}
 
Timer=0
 
endif
 
 
>E
 
;Executed when a Tasmota MQTT RESULT message is received
 
 
VOL=WebQuery#StatusSNS#ENERGY#Voltage
print Wert Volt %VOL%
 
CUR=WebQuery#StatusSNS#ENERGY#Current/1000
print Wert Current %CUR%
 
POW=WebQuery#StatusSNS#ENERGY#Power
print Wert Power %POW%
 
TOT=WebQuery#StatusSNS#ENERGY#Total
print Wert Total %TOT%
 
YES=WebQuery#StatusSNS#ENERGY#Yesterday
print Wert Yesterday %YES%
 
TOD=WebQuery#StatusSNS#ENERGY#Today
print Wert Today %TOD%
 
APP=WebQuery#StatusSNS#ENERGY#ApparentPower
print Wert Apparent Power %APP%
 
RAP=WebQuery#StatusSNS#ENERGY#ReactivePower
print Wert Reaktive Power %RAP%
 
 
>W
 
;The lines in this section are displayed in the web UI main page
 
          
Power{m} %2POW% W
Volt{m} %2VOL% V
Ampere{m} %2CUR% A
Total{m} %2TOT% 
Yesterday{m} %YES% 
Today{m} %2TOD% 
Apparent{m} %2APP% 
Reactive{m} %2RAP% 
 
 
 
#

Ich habe es nochmal verglichen. Ich habe lediglich die Zeilen 21 und 45 angepasst.

Ralla66

@ralfth sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

Die IP für das websend ist die des ioBroker oder der Gosund?

vom Gosund, das sieht doch gut aus :-)

Daten per IP websend kannst du von jedem Tasmota Gerät abfragen der die gleiche
StatusSNS/Energy/xxx............................ hat.

RalfTh

@ralla66 Ok, dann habe ich es richtig gemacht.

Allerdings stimmt der Inhalt nicht und diese Meldung scheint die Ursache zu sein:

18:34:19.588 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}

Steht auch in meinem letzten Post in der Konsolenausgabe.
Gebe ich im Browser http://192.168.178.164/cm?cmnd=status 10 ein erhalte ich folgendes:
{"StatusSNS":{"Time":"2023-11-15T18:37:01","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.556,"Yesterday":0.170,"Today":0.055,"Power":41,"ApparentPower":41,"ReactivePower":0,"Factor":1.00,"Voltage":229,"Current":0.181}}}

In der Konsole sieht es folgend aus:

18:38:48.972 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T18:38:48","Uptime":"0T12:01:26","UptimeSec":43286,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":4,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":82,"Signal":-59,"LinkCount":1,"Downtime":"0T00:00:03"}}
18:38:48.984 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T18:38:48","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.558,"Yesterday":0.170,"Today":0.057,"Period":1,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":229,"Current":0.183}}
18:38:50.972 SCR: performs "websend [192.168.178.164] /cm?cmnd=status 10"
18:38:56.176 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}
18:38:56.184 MQT: stat/tasmota_B8D3E7/RESULT = {"Total":0}
18:38:56.191 MQT: stat/tasmota_B8D3E7/RESULT = {"Yesterday":0}
18:38:56.199 MQT: stat/tasmota_B8D3E7/RESULT = {"Today":0}
18:38:56.206 MQT: stat/tasmota_B8D3E7/RESULT = {"ApparentPower":0}
18:38:56.213 MQT: stat/tasmota_B8D3E7/RESULT = {"ReactivePower":0.00}
18:38:56.221 MQT: stat/tasmota_B8D3E7/RESULT = {"Power":0}
18:38:56.228 MQT: stat/tasmota_B8D3E7/RESULT = {"Voltage":0}
18:38:56.235 MQT: stat/tasmota_B8D3E7/RESULT = {"Current":0}

In den ersten beiden Zeilen siehst du die JSON-Inhalte, aber ab Zeile 5 sind alle Werte 0??!!

Ich vermute das liegt am Connection failed in Zeile 4.

Ralla66

@ralfth

ja richtig, vermute da ist was falsch in Zeile 45 beim send
Hattest du nicht 2 Gosund ? Dann nimm mal die andere IP

RalfTh

@ralla66 ich habe viele. Du meinst ich soll mal die Daten einer anderen abfragen und publishen?!

Ralla66

@ralfth
ja zum testen ob websend rausgeht und ein Done kommt
Nachtrag: lösch mal den Kommentar
; MQT: tasmota_Reserve2 = {"StatusSNS":{"Time":"2023-11-14T12:59:46","ENERGY":{"TotalStart...............................
nicht das die Zeile zu lang ist

sp111 15112023.jpg

RalfTh

@ralla66 OK, hier kommt eine DONE. allerdings werden die Die Werte nich ins Result geschrieben. Oder werden sie nicht richt gelesen?

18:57:45.317 SCR: performs "websend [192.168.178.151] /cm?cmnd=status 10"
18:57:45.391 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Done"}
18:57:45.398 MQT: stat/tasmota_B8D3E7/RESULT = {"Total":0}
18:57:45.404 MQT: stat/tasmota_B8D3E7/RESULT = {"Yesterday":0}
18:57:45.408 MQT: stat/tasmota_B8D3E7/RESULT = {"Today":0}
18:57:45.412 MQT: stat/tasmota_B8D3E7/RESULT = {"ApparentPower":0}
18:57:45.416 MQT: stat/tasmota_B8D3E7/RESULT = {"ReactivePower":0.00}
18:57:45.421 MQT: stat/tasmota_B8D3E7/RESULT = {"Power":0}
18:57:45.425 MQT: stat/tasmota_B8D3E7/RESULT = {"Voltage":0}
18:57:45.429 MQT: stat/tasmota_B8D3E7/RESULT = {"Current":0}

Hier läuft übrigens eine .bin 13.2.0 DE ganz normal von der Tasmota-Seite.

@ralfth sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

Die folgenden defines sind nicht mehr Bestandteil my_user_config.h

#define USE_SCRIPT_GLOBVARS
#define USE_SCRIPT_STATUS
#define USE_SCRIPT_STATUS
#define USE_SCRIPT_FULL_JSON_PARSER
#define USE_SCRIPT_JSON_EXPORT
#define USE_SCRIPT_WEB_DISPLAY
#define USE_SCRIPT_SERIAL
#define USE_SML_M

Damit steht es nicht in Zusammenhang. Hatte ich weiter oben schon geschrieben.

Ralla66

@ralfth sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

192.168.178.151

geprüft im Browser ?
Topic ist default ?

RalfTh

@ralla66 sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

@ralfth sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

192.168.178.151

geprüft im Browser ?
Topic ist default ?

Ja und Ja

Browser-Antwort:
{"StatusSNS":{"Time":"2023-11-15T19:10:25","ENERGY":{"TotalStartTime":"2020-01-10T16:35:26","Total":196.003,"Yesterday":0.483,"Today":0.467,"Power":84,"ApparentPower":104,"ReactivePower":61,"Factor":0.81,"Voltage":226,"Current":0.459}}}

Ralla66

@ralfth

den langen kommentar hast du gelöscht ?
Telemetrie steht bei mir auf 10

RalfTh

@ralla66 Beides Ja, allerdings immer noch:

19:19:27.382 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}

Ich verstehe das nicht, wenn ich das im Webbrowser aufrufe funktioniert es doch!!!!

Das ist allerdings neu:

19:21:50.738 var not found: WebQuery#StatusSNS#ENERGY#Voltage
19:21:50.740 Wert Volt 0.00
19:21:50.742 var not found: WebQuery#StatusSNS#ENERGY#Current/1000
19:21:50.743 Wert Current 0.00
19:21:50.745 var not found: WebQuery#StatusSNS#ENERGY#Power
19:21:50.746 Wert Power 0.00
19:21:50.748 var not found: WebQuery#StatusSNS#ENERGY#Total
19:21:50.750 Wert Total 0.00
19:21:50.751 var not found: WebQuery#StatusSNS#ENERGY#Yesterday
19:21:50.753 Wert Yesterday 0.00
19:21:50.755 var not found: WebQuery#StatusSNS#ENERGY#Today
19:21:50.756 Wert Today 0.00
19:21:50.758 var not found: WebQuery#StatusSNS#ENERGY#ApparentPower
19:21:50.759 Wert Apparent Power 0.00
19:21:50.761 var not found: WebQuery#StatusSNS#ENERGY#ReactivePower
19:21:50.763 Wert Reaktive Power 0.00

Ralla66

@ralfth

Die folgenden defines sind nicht mehr Bestandteil my_user_config.h

#define USE_SCRIPT_GLOBVARS
#define USE_SCRIPT_STATUS
#define USE_SCRIPT_STATUS
#define USE_SCRIPT_FULL_JSON_PARSER

der Parser zerlegt die Antwort vom websend der Anfrage in Today, Voltage usw.
Der Parser wird zwingend benötigt.

RalfTh

@ralla66 OK, dann mach ich mich erst mal da dran un compiliere eine neue .bin

Melde mich dann wieder. Und vielen Dank für Deine Unterstützung.

RalfTh

@ralla66 Dieses define steht in der my_user_config.h ??

Ralla66

@ralfth

und nimm bitte alle define USE_xxxxx
Auf git liefen meine .bin auch nicht,erst die mit Tasmocompiler erstellten
liefen dann. Probiers mal.

RalfTh

@ralla66 Meinst du den GitPod oder ist der Tasmotacompiler noch was anderes. GitPod ist so ne Browsererweiterung auf Basis VSC

@ralla66 sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

#define USE_SCRIPT_GLOBVARS
#define USE_SCRIPT_STATUS
#define USE_SCRIPT_STATUS
#define USE_SCRIPT_FULL_JSON_PARSER

Hier ein Auszug aus der my_user_config.h nach der Suche nach dem Wort Script:

// -- Rules or Script  ----------------------------
// Select none or only one of the below defines USE_RULES or USE_SCRIPT
#define USE_RULES                                // Add support for rules (+8k code)
//  #define USE_EXPRESSION                         // Add support for expression evaluation in rules (+3k2 code, +64 bytes mem)
//    #define SUPPORT_IF_STATEMENT                 // Add support for IF statement in rules (+4k2 code, -332 bytes mem)
//  #define USER_RULE1 "<Any rule1 data>"          // Add rule1 data saved at initial firmware load or when command reset is executed
//  #define USER_RULE2 "<Any rule2 data>"          // Add rule2 data saved at initial firmware load or when command reset is executed
//  #define USER_RULE3 "<Any rule3 data>"          // Add rule3 data saved at initial firmware load or when command reset is executed

//#define USE_SCRIPT                               // Add support for script (+17k code)
//  #define USE_SCRIPT_FATFS 4                     // Script: Add FAT FileSystem Support
//  #define SUPPORT_MQTT_EVENT                     // Support trigger event with MQTT subscriptions (+3k5 code)

Und weiter unten:

#if defined(USE_RULES) && defined(USE_SCRIPT)
  #error "Select either USE_RULES or USE_SCRIPT. They can't both be used at the same time"
#endif

Diese Defines stehen nicht in der aktuellen my_user_config.h . Soll ich die einfach mal in die user_config-override.h eintragen??

Ralla66

@ralfth

keine Ahnung von my_user_config.h

die:

#define USE_TIMERS
#define USE_SCRIPT
#define USE_SCRIPT_GLOBVARS
#define USE_SCRIPT_STATUS
#define USE_WEBSEND_RESPONSE
#define USE_SCRIPT_STATUS
#define USE_SCRIPT_FULL_JSON_PARSER
#define USE_SCRIPT_JSON_EXPORT
#define SUPPORT_MQTT_EVENT
#define USE_SML_M
#define USE_SCRIPT_WEB_DISPLAY
#define USE_SCRIPT_SERIAL

Community Forum

NEWS

Gosund SP111 mit Tasmota 13.2.0 Problem mit DP

Support us

795

32.5k

81.8k

1.3m