Zigbee adapter stopped working FIXED

[ap2017]

@Asgothian Not sure how to check it. I only have three hardware related adapters: zWave which is on ACM0, mySensors on USB0 and zigbee on ACM1. As I mention before, if I disable zigbee, zWave runs fine on ACM1.

[ap2017]

@Asgothian Interesting that if I try to use other port like S1, getting different error message

"Error: Error while opening serialport 'Error: Error: Input/output error setting custom baud rate of 115200' at Znp.<anonymous> (/opt/iobroker/node_modules/iobroker.zigbee/node_modules/zigbe"

[ap2017]

@Asgothian Running ioBroker fixer did not help:

sudo iobroker stop
curl -sL https://iobroker.net/fix.sh | bash -
sudo iobroker start

[ap2017]

@Asgothian During npm rebuild received bunch of errors associated with serial port, see log. Could it be related to my problem?
2020-09-23T02_39_28_639Z-debug.log

[Asgothian]

@ap2017
It should not. You have an old version of the serial port library (6.2.2) still installed. The zigbee-adapter should use serial port 9.x
Can you check NPM List if it is still present ?
You might see a large number of "extraneous" packages listed.
I would suggest to run "npm prune --dry-run" to see what is removed if you prune, and - unless packages are removed you consider needed - follow it up with an "npm prune"

A.

[ap2017]

@Asgothian Pardon my ignorance, how do I check NPM list? In terms of pruning, I have no idea what do I needs. I have very rudimentary knowledge of command line controls, I am one of those users who appreciate very much object level system configuration. That is why I like ioBroker, it seems to me well though through for this purpose. As always, thank you for your time and help.

[Thomas Braun]

@ap2017

cd /opt/iobroker
npm list serialport

Should look similar to

pi@raspberrypi:/opt/iobroker $ npm list serialport
iobroker.inst@2.0.3 /opt/iobroker
└─┬ iobroker.zigbee@1.2.1
  └─┬ zigbee-herdsman@0.12.117
    └── serialport@9.0.1

[ap2017]

@Thomas-Braun said in Zigbee adapter stopped working:

npm list serialport

Here we go:

[Asgothian]

@ap2017 I apologise. I should have put quotes around the "npm list", as that was the command i wanted you to check.

As you can see, there is an extra serialport library installed, but each adapter has (should have) a usable version, so you should be able to remove the extra one.

npm prune should get rid of it.

A.

[ap2017]

@Asgothian No problem. I run the following, but still have same extraneous serial library 6..2.2 when run "npm list serialport"

cd /opt/iobroker
npm prune --dry-run
sudo reboot

[ap2017]

@Asgothian As previously, keep getting these errors:

zigbee.0 2020-09-24 10:39:10.082 error (2461) Error: Error while opening serialport 'Error: Error: Device or resource busy, cannot open /dev/ttyACM1' at Znp.<anonymous> (/opt/iobroker/node_modules/iobroker.zigbee/node_modules/zigbee-he
zigbee.0 2020-09-24 10:39:10.081 error (2461) Failed to start Zigbee
zigbee.0 2020-09-24 10:39:09.975 info (2461) Starting Zigbee...
zigbee.0 2020-09-24 10:39:09.974 info (2461) Try to reconnect. 1 attempts left
zigbee.0 2020-09-24 10:38:59.972 error (2461) Error: Failed to connect to the adapter (Error: Cannot request when znp has not been initialized yet) at ZStackAdapter.<anonymous> (/opt/iobroker/node_modules/iobroker.zigbee/node_modules/z
zigbee.0 2020-09-24 10:38:59.972 error (2461) Failed to start Zigbee

[Asgothian]

@ap2017
Of course.. the "npm prune --dry-run" only lists what it would do. This is to ensure that it doesn't get rid of something you want to keep
once you checked the list, you can do "npm prune" (without the dry run)

a Reboot is not needed..

A.

[ap2017]

@Asgothian The unwanted serial driver 6.2.2 disappeared after pruning, but it did not help to resolve the main issue, see errors below. I rebooted controller after pruning, just in case.

[Asgothian]

@ap2017
Unfortunately, that is what i expected. Now you should no longer get any errors on an npm rebuild, but i have the feeling that is not the error. I am starting to think that the firmware on the Zigbee Board / Stick is not responding correctly.

As long as there is a message that the zigbee library cannot be initialized, the issue is most likely hardware related.

A.

[Thomas Braun]

@ap2017
Please stop the zwave Adapater and reboot. I may happen that the zwo adapters do block the port.
And I see a duplicate entry in the zwave entry. I think that only one entry should show there.

[ap2017]

@Thomas-Braun I stopped both zwave and zigbee and rebooted, here is list of serial ports:

As I mentioned before, when zigbee is off, zwave works fine on both ports ACM0 and ACM1, so it looks like system works properly with ports.

What would be next step, try to uninstall and reinstall zigbee adapter again? Re-flash CC2531 dongle? Thank you.

[Asgothian]

@ap2017
No.

Please verify if the Zigbee Adapter will start when

• no zwave sticks are connected to the system
• no zwave adapter is running.

A.

[ap2017]

@Asgothian Sorry, how do I check if zigbee adapter started?

[Asgothian]

@ap2017 Watch the log for an entry that the zigbee adapter started successfully, alternatively, watch the green light in the instance list.

[ap2017]

@Asgothian Of course, I did not pay attention that you asked to disable zwave, not zigbee. Unplugging zwave dongle and disabling zwave adapter did not help. FYI, zigbee behaves same way for ACM0 and ACM1 ports