Navigation

    Logo
    • Register
    • Login
    • Search
    • Recent
    • Tags
    • Unread
    • Categories
    • Unreplied
    • Popular
    • GitHub
    • Docu
    • Hilfe
    1. Home
    2. Deutsch
    3. Hardware
    4. Gosund SP111 mit Tasmota 13.2.0 Problem mit DP

    NEWS

    • ioBroker@Smart Living Forum Solingen, 14.06. - Agenda added

    • ioBroker goes Matter ... Matter Adapter in Stable

    • Monatsrückblick - April 2025

    Gosund SP111 mit Tasmota 13.2.0 Problem mit DP

    This topic has been deleted. Only users with topic management privileges can see it.
    • Ralla66
      Ralla66 Most Active @RalfTh last edited by

      @ralfth
      der Sonoff Adapter ist ja kein echter Mqtt Broker

      1 Reply Last reply Reply Quote 0
      • Ralla66
        Ralla66 Most Active @RalfTh last edited by Ralla66

        @ralfth

        testen kannste hiermit,
        subcribe, publish der Teledaten nach Sonoff Adapter alle 10 sec,
        einfügen deiner Daten sollte ja klar sein.
        Schwierigkeitsgrad: Anspruchsvoll 🙂

        Pub_Sub.jpg

        >D

;a valid script must start with >D in the first line


Timer=0

WEBQ=5

VOL=0
CUR=0
POW=0
TOT=0
YES=0
TOD=0
APP=0
RAP=0

; Beispiel

;{"StatusSNS":{"Time":"2023-11-12T13:25:55","ENERGY":
;{"TotalStartTime":"2023-07-01T15:59:16","Total":63.255,"Yesterday":0.056,"Today":0.075,
;"Power":4,"ApparentPower":66,"ReactivePower":66,"Factor":0.07,"Voltage":235,"Current":0.283}}}

>BS

+>subscribe EA, cmnd/%topic%/Total
+>subscribe EA, cmnd/%topic%/Yesterday
+>subscribe EA, cmnd/%topic%/Today
+>subscribe EA, cmnd/%topic%/Power
+>subscribe EA, cmnd/%topic%/ApparentPower
+>subscribe EA, cmnd/%topic%/ReactivePower
+>subscribe EA, cmnd/%topic%/Power
+>subscribe EA, cmnd/%topic%/Voltage
+>subscribe EA, cmnd/%topic%/Current

>S

Timer+=1

;Executed every second 


if Timer>10

then
=>websend [192.168.2.85] /cm?cmnd=status 10

+>publish stat/%topic%/RESULT {"Total":%0TOT%}
+>publish stat/%topic%/RESULT {"Yesterday":%0YES%}
+>publish stat/%topic%/RESULT {"Today":%0TOD%}
+>publish stat/%topic%/RESULT {"ApparentPower":%0APP%}
+>publish stat/%topic%/RESULT {"ReactivePower":%RAP%}
+>publish stat/%topic%/RESULT {"Power":%0POW%}
+>publish stat/%topic%/RESULT {"Voltage":%0VOL%}
+>publish stat/%topic%/RESULT {"Current":%0CUR%}

Timer=0

endif


>E

;Executed when a Tasmota MQTT RESULT message is received


VOL=WebQuery#StatusSNS#ENERGY#Voltage
print Wert Volt %VOL%

CUR=WebQuery#StatusSNS#ENERGY#Current/1000
print Wert Current %CUR%

POW=WebQuery#StatusSNS#ENERGY#Power
print Wert Power %POW%

TOT=WebQuery#StatusSNS#ENERGY#Total
print Wert Total %TOT%

YES=WebQuery#StatusSNS#ENERGY#Yesterday
print Wert Yesterday %YES%

TOD=WebQuery#StatusSNS#ENERGY#Today
print Wert Today %TOD%

APP=WebQuery#StatusSNS#ENERGY#ApparentPower
print Wert Apparent Power %APP%

RAP=WebQuery#StatusSNS#ENERGY#ReactivePower
print Wert Reaktive Power %RAP%


>W

;The lines in this section are displayed in the web UI main page

          
Power{m} %2POW% W
Volt{m} %2VOL% V
Ampere{m} %2CUR% A
Total{m} %2TOT% 
Yesterday{m} %YES% 
Today{m} %2TOD% 
Apparent{m} %2APP% 
Reactive{m} %2RAP% 



#
        RalfTh 2 Replies Last reply Reply Quote 0
        • RalfTh
          RalfTh @Ralla66 last edited by RalfTh

          @ralla66 Wie ich sehe hast du als Modul sonoff basic verwendet und wohl auch die tasmota_DE.bin installiert. Bei mir fehlt der Button für das Skripting. Welches Binary hast du installiert?

          Edit: Ok, habe gerade gesehen, dass diese Funktion nicht in den precompiled Binaries enthalten ist und über die Konsole gemacht werden muss. ----- Das funktioniert nicht mit "Edit Skript" bzw. "Edit script"

          Ralla66 1 Reply Last reply Reply Quote 0
          • Ralla66
            Ralla66 Most Active @RalfTh last edited by Ralla66

            @ralfth

            hatte ich mit Tasmocompiler selbst erstellt als Generic,
            eine eigene Test .bin wo das meiste mit drin ist.

            #define USE_TIMERS
            #define USE_SCRIPT
            #define USE_SCRIPT_GLOBVARS
            #define USE_SCRIPT_STATUS
            #define USE_WEBSEND_RESPONSE
            #define USE_SCRIPT_STATUS
            #define USE_SCRIPT_FULL_JSON_PARSER
            #define USE_SCRIPT_JSON_EXPORT
            #define SUPPORT_MQTT_EVENT
            #define USE_SML_M
            #define USE_SCRIPT_WEB_DISPLAY
            #define USE_SCRIPT_SERIAL

            RalfTh 1 Reply Last reply Reply Quote 0
            • RalfTh
              RalfTh @Ralla66 last edited by

              @ralla66 sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

              #define USE_TIMERS
              #define USE_SCRIPT
              #define SUPPORT_MQTT_EVENT
              #define USE_WEBSEND_RESPONSE

              Das oben habe ich gefunden im aktuellen Release. Aktiviere ich USE_SCRIPT muss ich allerdings USE_RULES deaktivieren sofern ich diese Zeile richtig interpretiere:

              #if defined(USE_RULES) && defined(USE_SCRIPT)
  #error "Select either USE_RULES or USE_SCRIPT. They can't both be used at the same time"
#endif

              Die folgenden defines sind nicht mehr Bestandteil my_user_config.h

              #define USE_SCRIPT_GLOBVARS
              #define USE_SCRIPT_STATUS
              #define USE_SCRIPT_STATUS
              #define USE_SCRIPT_FULL_JSON_PARSER
              #define USE_SCRIPT_JSON_EXPORT
              #define USE_SCRIPT_WEB_DISPLAY
              #define USE_SCRIPT_SERIAL
              #define USE_SML_M

              Jetz habe ich das mal compiliert und werde es ausprobieren und berichten.

              Ralla66 1 Reply Last reply Reply Quote 0
              • Ralla66
                Ralla66 Most Active @RalfTh last edited by Ralla66

                @ralfth

                es geht nur Script oder Rules.
                Versuche mal den Tasmocompiler, der Json Parser usw. wird ja gebraucht.
                Zur Not kann man auch auf Git anstatt per my_user_config.h die define per Hand aktivieren.
                Dann muß das // entfernt werden. Da bin ich aber nicht so tief drin.

                Tasmocompiler
                unter custom Parameters die define hinzufügen.

                1 Reply Last reply Reply Quote 0
                • RalfTh
                  RalfTh @Ralla66 last edited by RalfTh

                  @ralla66 sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

                  >E
 
;Executed when a Tasmota MQTT RESULT message is received
 
 
VOL=WebQuery#StatusSNS#ENERGY#Voltage
print Wert Volt %VOL%
 
CUR=WebQuery#StatusSNS#ENERGY#Current/1000
print Wert Current %CUR%
 
POW=WebQuery#StatusSNS#ENERGY#Power
print Wert Power %POW%
 
TOT=WebQuery#StatusSNS#ENERGY#Total
print Wert Total %TOT%
 
YES=WebQuery#StatusSNS#ENERGY#Yesterday
print Wert Yesterday %YES%
 
TOD=WebQuery#StatusSNS#ENERGY#Today
print Wert Today %TOD%
 
APP=WebQuery#StatusSNS#ENERGY#ApparentPower
print Wert Apparent Power %APP%
 
RAP=WebQuery#StatusSNS#ENERGY#ReactivePower
print Wert Reaktive Power %RAP%
 
 
>W
 
;The lines in this section are displayed in the web UI main page
 
          
Power{m} %2POW% W
Volt{m} %2VOL% V
Ampere{m} %2CUR% A
Total{m} %2TOT% 
Yesterday{m} %YES% 
Today{m} %2TOD% 
Apparent{m} %2APP% 
Reactive{m} %2RAP%

                  Das mit der Firmware (bei mir 13.2.0.2 mit GitPod kompiliert) hat jetzt super geklappt.

                  Ich habe dein Skript mal reinkopiert und aktiviert. Die DP's werden angelegt. Allerdings werden die definierten Variablen nicht gefüllt wie es eigentliche in "E" geschehen sollte. habe mal einen Wert anders initialisiert und dieser Wert wurde ausgegeben und nicht etwa durch das Ergebnis der Query ersetzt.

                  Auch das was in >W ausgegeben werden soll erscheint nicht. Wenn ich etwas sehen will muss ich die Vorlage entsprechend aktivieren.

                  Die IP habe ich an meine MQTT-Einstellung angepasst.

                  Habe ich da was vergessen anzupassen?

                  Ralla66 1 Reply Last reply Reply Quote 0
                  • Ralla66
                    Ralla66 Most Active @RalfTh last edited by Ralla66

                    @ralfth sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

                    Habe ich da was vergessen anzupassen?

                    das muß an deinen Teledaten vom SP angepasst werden.

                    08:12:14.187 MQT: tele/tasmota_26536D/SENSOR = {"Time":"2023-11-06T08:12:14","ENERGY":{"TotalStartTime":"2020-01-07T09:52:26","Total":0.890,"Yesterday":0.600,"Today":0.290,"Period":2,"Power":797,"ApparentPower":797,"ReactivePower":0,"Factor":1.00,"Voltage":223,"Current":3.569}}

                    IP nimm die vom SP , =>websend [ deine IP] /cm?cmnd=status 10

                    beim mir ist ja der Pfad -> #StatusSNS#ENERGY#Today
                    bei dir ja nur #ENERGY#Today

                    -> Auch das was in >W ausgegeben werden soll erscheint nicht
                    Reboot gemacht ? Script aktiviert ?
                    sonst fehlt die #define USE_SCRIPT_WEB_DISPLAY

                    Teste mal im Browser gegen mit http:// deine IP /cm?cmnd=status 10
                    dann sollten Daten und Pfade sichtbar sein.

                    RalfTh 1 Reply Last reply Reply Quote 0
                    • RalfTh
                      RalfTh @Ralla66 last edited by RalfTh

                      @ralla66

                      {"StatusSNS":{"Time":"2023-11-14T12:59:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.424,"Yesterday":0.007,"Today":0.093,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":231,"Current":0.181}}}

                      So sieht die Rückmeldung aus , wenn ich im Webbrowser "http://192.xxx.xxx.xxx/cm?cmnd=status 10" eingebe.

                      Mein Script:

                      >D
 
;a valid script must start with >D in the first line
 
 
Timer=0
 
WEBQ=5
 
VOL=0
CUR=0
POW=0
TOT=0
YES=0
TOD=0
APP=0
RAP=0
 
; Meins
 
MQT: tasmota_Reserve2/cmnd = {"StatusSNS":{"Time":"2023-11-14T12:59:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.424,"Yesterday":0.007,"Today":0.093,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":231,"Current":0.181}}}
 
>BS
 
+>subscribe EA, %topic%/cmnd/Total
+>subscribe EA, %topic%/cmnd/Yesterday
+>subscribe EA, %topic%/cmnd/Today
+>subscribe EA, %topic%/cmnd/Power
+>subscribe EA, %topic%/cmnd/ApparentPower
+>subscribe EA, %topic%/cmnd/ReactivePower
+>subscribe EA, %topic%/cmnd/Power
+>subscribe EA, %topic%/cmnd/Voltage
+>subscribe EA, %topic%/cmnd/Current
 
>S
 
Timer+=1
 
;Executed every second 
 
 
if Timer>10
 
then
=>websend 192.168.178:164/cm?cmnd=status 10
 
+>publish %topic%/ENERGY_Total {%0TOT% kWh}
+>publish %topic%/ENERGY_Yesterday {%0YES% kWh}
+>publish %topic%/ENERGY_Today {%0TOD% kWh}
+>publish %topic%/ENERGY_ApparentPower {%0APP% VA}
+>publish %topic%/ENERGY_ReactivePower {%RAP% VAR}
+>publish %topic%/ENERGY_Power {%0POW% W}
+>publish %topic%/ENERGY_Voltage {%0VOL% V}
+>publish %topic%/ENERGY_Current {%0CUR% A}
 
Timer=0
 
endif
 
 
>E
 
;Executed when a Tasmota MQTT RESULT message is received
 
VOL=WebQuery#StatusSNS#ENERGY#Voltage
print Wert Volt %VOL%
 
CUR=WebQuery#StatusSNS#ENERGY#Current/1000
print Wert Current %CUR%
 
POW=WebQuery#StatusSNS#ENERGY#Power
print Wert Power %POW%
 
TOT=WebQuery#StatusSNS#ENERGY#Total
print Wert Total %TOT%
 
YES=WebQuery#StatusSNS#ENERGY#Yesterday
print Wert Yesterday %YES%
 
TOD=WebQuery#StatusSNS#ENERGY#Today
print Wert Today %TOD%
 
APP=WebQuery#StatusSNS#ENERGY#ApparentPower
print Wert Apparent Power %APP%
 
RAP=WebQuery#StatusSNS#ENERGY#ReactivePower
print Wert Reaktive Power %RAP%
 
 
>W
 
;The lines in this section are displayed in the web UI main page
 
          
Power{m} %2POW% W
Volt{m} %2VOL% V
Ampere{m} %2CUR% A
Total{m} %2TOT% 
Yesterday{m} %YES% 
Today{m} %2TOD% 
Apparent{m} %2APP% 
Reactive{m} %2RAP% 

 
#

                      Hier mal ein Auszug was im MQTT-Explorer sieht:
                      d6390e06-63a5-4ad2-86c2-e4a930f6a3bd-image.png

                      Auffällig ist der DP tasmota_Reserve2/stat/RESULT Hier erscheint "Websend":Wrong Parameters

                      52378906-83b0-42aa-b9ef-ce432e619895-image.png

                      Einiges habe ich angepasst, weil ich in MQTT am Topic und Full-Topic was geändert habe. Mein Full-Topic den Eintrag %topic%/%prefix%/ damit in MQTT der Baum anders aufgebaut wird. Das habe ich beim subscribe berücksichtigt. Und das Publish habe ich direkt unter dem Topic vorgenommen.

                      Allerdings habe ich auch schon dein Original (natürlich mit den spez. Anpassungen) ausprobiert mit dem gleichen Ergebnis. Die DP's werden nicht aktualisiert

                      Was mache ich falsch?

                      Ralla66 1 Reply Last reply Reply Quote 0
                      • Ralla66
                        Ralla66 Most Active @RalfTh last edited by Ralla66

                        @ralfth sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

                        weil ich in MQTT am Topic und Full-Topic was geändert habe

                        Erst auf default lassen bis das läuft.
                        Das mag Tasmota gar nicht.
                        Mqtt kannst du später prüfen, das muß erst auf dem ESP laufen.

                        ! hinter dem ; ist Text und wird im Programm nicht Berücksichtigt
                        da fehlt was am Anfang ; MQT: tasmota_Reserve2/cmnd = {"StatusSNS":{"Time":"2023-11-14T...........................

                        Nicht soviel auf einmal ändern , macht nur das Debuggen schwerer.

                        Ralla66 1 Reply Last reply Reply Quote 0
                        • Ralla66
                          Ralla66 Most Active @Ralla66 last edited by Ralla66

                          @ralla66

                          Wrong Parameters kann auch vom publish sein, sowas {%0TOT% kWh}
                          Das subscribe und publish ist auf Sonoff Adapter gemünzt, nicht für Mqtt Adapter.

                          Nachtrag eckige Klammern !

                          if Timer>10

                          then
                          =>websend [192.168.2.85] /cm?cmnd=status 10

                          RalfTh 1 Reply Last reply Reply Quote 0
                          • RalfTh
                            RalfTh @Ralla66 last edited by RalfTh

                            @ralla66 Habe jetzt dein original Script eingebunden:

                            >D
 
;a valid script must start with >D in the first line
 
 
Timer=0
 
WEBQ=5
 
VOL=0
CUR=0
POW=0
TOT=0
YES=0
TOD=0
APP=0
RAP=0
 
; Meins
 
; MQT: tasmota_Reserve2 = {"StatusSNS":{"Time":"2023-11-14T12:59:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.424,"Yesterday":0.007,"Today":0.093,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":231,"Current":0.181}}}
 
>BS
 
+>subscribe EA, cmnd/%topic%/Total
+>subscribe EA, cmnd/%topic%/Yesterday
+>subscribe EA, cmnd/%topic%/Today
+>subscribe EA, cmnd/%topic%/Power
+>subscribe EA, cmnd/%topic%/ApparentPower
+>subscribe EA, cmnd/%topic%/ReactivePower
+>subscribe EA, cmnd/%topic%/Power
+>subscribe EA, cmnd/%topic%/Voltage
+>subscribe EA, cmnd/%topic%/Current
 
>S
 
Timer+=1
 
;Executed every second 
 
 
if Timer>10
 
then
=>websend [192.168.178.164] /cm?cmnd=status 10
 
+>publish stat/%topic%/RESULT {"Total":%0TOT%}
+>publish stat/%topic%/RESULT {"Yesterday":%0YES%}
+>publish stat/%topic%/RESULT {"Today":%0TOD%}
+>publish stat/%topic%/RESULT {"ApparentPower":%0APP%}
+>publish stat/%topic%/RESULT {"ReactivePower":%RAP%}
+>publish stat/%topic%/RESULT {"Power":%0POW%}
+>publish stat/%topic%/RESULT {"Voltage":%0VOL%}
+>publish stat/%topic%/RESULT {"Current":%0CUR%}
 
Timer=0
 
endif
 
 
>E
 
;Executed when a Tasmota MQTT RESULT message is received
 
 
VOL=WebQuery#StatusSNS#ENERGY#Voltage
print Wert Volt %VOL%
 
CUR=WebQuery#StatusSNS#ENERGY#Current/1000
print Wert Current %CUR%
 
POW=WebQuery#StatusSNS#ENERGY#Power
print Wert Power %POW%
 
TOT=WebQuery#StatusSNS#ENERGY#Total
print Wert Total %TOT%
 
YES=WebQuery#StatusSNS#ENERGY#Yesterday
print Wert Yesterday %YES%
 
TOD=WebQuery#StatusSNS#ENERGY#Today
print Wert Today %TOD%
 
APP=WebQuery#StatusSNS#ENERGY#ApparentPower
print Wert Apparent Power %APP%
 
RAP=WebQuery#StatusSNS#ENERGY#ReactivePower
print Wert Reaktive Power %RAP%
 
 
>W
 
;The lines in this section are displayed in the web UI main page
 
          
Power{m} %2POW% W
Volt{m} %2VOL% V
Ampere{m} %2CUR% A
Total{m} %2TOT% 
Yesterday{m} %YES% 
Today{m} %2TOD% 
Apparent{m} %2APP% 
Reactive{m} %2RAP% 
  
#

                            angepasst habe ich Zeile 21 und 45

                            Im Log des ioBroker steht:

                            
sonoff.0
2023-11-14 18:48:06.358	debug	[Reserve2] Received: stat/tasmota_Reserve2/RESULT = {"WebSend":"Connect failed"}

                            Habe keine Ahnung woran das liegen kann.

                            Nachtrag:
                            3322f7f1-a10c-455d-a08c-40e4eacc65db-image.png
                            e66ab1cf-68b5-4c50-9994-0d9f5a8a7566-image.png

                            Ralla66 2 Replies Last reply Reply Quote 0
                            • Ralla66
                              Ralla66 Most Active @RalfTh last edited by Ralla66

                              @ralfth

                              Passwort Rot ? Zum testen einfach 12345 nehmen
                              Topic nicht default

                              was steht in der Console ?
                              websend done ?

                              Nachtrag:

                              Das ist alles verbogen,
                              neu flashen
                              gosund einrichten template
                              nix an Topic / Full Topic basteln, rein gar nix !!
                              im Sonoff Adapter altes löschen
                              Mqtt verbinden
                              das muß erst einmal rennen
                              danach Script einfügen, speichern, rebooten,aktivieren

                              1 Reply Last reply Reply Quote 0
                              • Ralla66
                                Ralla66 Most Active @RalfTh last edited by

                                @ralfth

                                was bastelst du da 🙂

                                sp 111 14112023.jpg

                                RalfTh 1 Reply Last reply Reply Quote 0
                                • RalfTh
                                  RalfTh @Ralla66 last edited by

                                  @ralla66 So, habe jetzt alles so eingestellt wie du es mir in den Bildern gezeigt hast. Habe vorher den Adapter gestoppt und die Objekte gelöscht.
                                  Das Script ist nicht aktiviert.
                                  Instanz gestartet, die Objekte werden angelegt.
                                  Di DP's welche mit "ENERGY_" beginnen werden,wenn überhaupt nur nach einer Ewigkeit aktualisiert und das obwohl die Message ankam. Hier Auszug aus der Konsole:

                                  B8D3E7/POWER = ON
07:14:16.291 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:14:16","Uptime":"0T00:36:54","UptimeSec":2214,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":58,"Signal":-71,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:14:16.302 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:14:16","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.527,"Yesterday":0.170,"Today":0.026,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.183}}
07:14:46.290 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:14:46","Uptime":"0T00:37:24","UptimeSec":2244,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:14:46.299 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:14:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.528,"Yesterday":0.170,"Today":0.027,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.183}}
07:15:16.280 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:15:16","Uptime":"0T00:37:54","UptimeSec":2274,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:15:16.293 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:15:16","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.528,"Yesterday":0.170,"Today":0.027,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.183}}
07:15:46.251 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:15:46","Uptime":"0T00:38:24","UptimeSec":2304,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":64,"Signal":-68,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:15:46.262 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:15:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.528,"Yesterday":0.170,"Today":0.027,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.186}}
07:16:16.257 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:16:16","Uptime":"0T00:38:54","UptimeSec":2334,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":20,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:16:16.267 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:16:16","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.529,"Yesterday":0.170,"Today":0.028,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.185}}
07:16:46.256 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:16:46","Uptime":"0T00:39:24","UptimeSec":2364,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:16:46.268 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:16:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.529,"Yesterday":0.170,"Today":0.028,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.186}}
07:17:16.261 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:17:16","Uptime":"0T00:39:54","UptimeSec":2394,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":60,"Signal":-70,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:17:16.273 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:17:16","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.530,"Yesterday":0.170,"Today":0.029,"Period":0,"Power":44,"ApparentPower":44,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.188}}
07:17:46.275 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T07:17:46","Uptime":"0T00:40:24","UptimeSec":2424,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":3,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":62,"Signal":-69,"LinkCount":1,"Downtime":"0T00:00:03"}}
07:17:46.285 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T07:17:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.530,"Yesterday":0.170,"Today":0.029,"Period":0,"Power":43,"ApparentPower":43,"ReactivePower":0,"Factor":1.00,"Voltage":232,"Current":0.185}}

                                  Derweil im ioBroker:
                                  4ba186da-a727-4d8a-87ea-4a9fed0a30ed-image.png

                                  Und das, obwohl laut LOG auch hier die Informationen eintrudeln:

                                  8298ba6c-3c66-4b07-8f66-7a0042033f63-image.png

                                  Ich habe die Steckdose mittlerweile drei mal geflasht und jedesmal eine andere Konfiguration verwendet. Ich denke, ein erneutes flashen bringt da auch nicht die Lösung. Falls keine anderen Ideen mehr da sind werde ich mir einen anderen MQTT-Broker suchen und das JSON aufdröseln.

                                  Ralla66 1 Reply Last reply Reply Quote 0
                                  • Ralla66
                                    Ralla66 Most Active @RalfTh last edited by

                                    @ralfth

                                    alle print des Scriptes werden in der Console nicht ausgegeben, bedeutet dein Script läuft nicht.
                                    Topic ist noch Reserve2 und nicht default.
                                    Ob deine .bin überhaupt in Ordnung ist weiß keiner.
                                    Daher das compilieren mit Tasmocompiler. Das ist halt viel einfacher.

                                    Solange die Topic / Full Topic nicht in Ordnung sind und das Script nicht läuft kann
                                    ich auch nicht weiter helfen. Da es ja bei mir läuft liegt das ja an deinem System.

                                    RalfTh 1 Reply Last reply Reply Quote 0
                                    • RalfTh
                                      RalfTh @Ralla66 last edited by

                                      @ralla66 sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

                                      alle print des Scriptes werden in der Console nicht ausgegeben, bedeutet dein Script läuft nicht.

                                      Hatte ich auch geschrieben, dass das Script nicht aktiviert ist.

                                      Meine .bin habe ich mit Gitpod kompiliert (Quelle: https://github.com/arendst/Tasmota) und alle von dir genannten Defines, soweit in my_user_config.h vorhanden, aktiviert. In einem Post weiter oben hatte ich das auch schon erwähnt.
                                      Diese .bin habe ich dann auf den Gosund geflasht.

                                      Das Script habe ich jetzt aktiviert und in der Konsole kommt folgende Fehlermeldung:

                                      17:32:38.869 SCR: performs "websend [192.168.178.164] /cm?cmnd=status 10"
17:32:44.249 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}
17:32:44.257 MQT: stat/tasmota_B8D3E7/RESULT = {"Total":0}
17:32:44.264 MQT: stat/tasmota_B8D3E7/RESULT = {"Yesterday":0}
17:32:44.272 MQT: stat/tasmota_B8D3E7/RESULT = {"Today":0}
17:32:44.279 MQT: stat/tasmota_B8D3E7/RESULT = {"ApparentPower":0}
17:32:44.286 MQT: stat/tasmota_B8D3E7/RESULT = {"ReactivePower":0.00}
17:32:44.293 MQT: stat/tasmota_B8D3E7/RESULT = {"Power":0}
17:32:44.300 MQT: stat/tasmota_B8D3E7/RESULT = {"Voltage":0}
17:32:44.307 MQT: stat/tasmota_B8D3E7/RESULT = {"Current":0}
17:32:48.393 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T17:32:48","Uptime":"0T10:55:26","UptimeSec":39326,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":4,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":96,"Signal":-52,"LinkCount":1,"Downtime":"0T00:00:03"}}
17:32:48.406 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T17:32:48","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.544,"Yesterday":0.170,"Today":0.043,"Period":1,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":230,"Current":0.181}}
17:32:54.371 SCR: performs "websend [192.168.178.164] /cm?cmnd=status 10"
17:32:59.783 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}
17:32:59.792 MQT: stat/tasmota_B8D3E7/RESULT = {"Total":0}
17:32:59.799 MQT: stat/tasmota_B8D3E7/RESULT = {"Yesterday":0}
17:32:59.808 MQT: stat/tasmota_B8D3E7/RESULT = {"Today":0}
17:32:59.815 MQT: stat/tasmota_B8D3E7/RESULT = {"ApparentPower":0}
17:32:59.823 MQT: stat/tasmota_B8D3E7/RESULT = {"ReactivePower":0.00}

                                      Die IP für das websend ist die des ioBroker oder der Gosund?

                                      Hier noch mal mein Script:

                                      >D
 
;a valid script must start with >D in the first line
 
 
Timer=0
 
WEBQ=5
 
VOL=0
CUR=0
POW=0
TOT=0
YES=0
TOD=0
APP=0
RAP=0
 
; Meins
 
; MQT: tasmota_Reserve2 = {"StatusSNS":{"Time":"2023-11-14T12:59:46","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.424,"Yesterday":0.007,"Today":0.093,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":231,"Current":0.181}}}
 
>BS
 
+>subscribe EA, cmnd/%topic%/Total
+>subscribe EA, cmnd/%topic%/Yesterday
+>subscribe EA, cmnd/%topic%/Today
+>subscribe EA, cmnd/%topic%/Power
+>subscribe EA, cmnd/%topic%/ApparentPower
+>subscribe EA, cmnd/%topic%/ReactivePower
+>subscribe EA, cmnd/%topic%/Power
+>subscribe EA, cmnd/%topic%/Voltage
+>subscribe EA, cmnd/%topic%/Current
 
>S
 
Timer+=1
 
;Executed every second 
 
 
if Timer>10
 
then
=>websend [192.168.178.164] /cm?cmnd=status 10
 
+>publish stat/%topic%/RESULT {"Total":%0TOT%}
+>publish stat/%topic%/RESULT {"Yesterday":%0YES%}
+>publish stat/%topic%/RESULT {"Today":%0TOD%}
+>publish stat/%topic%/RESULT {"ApparentPower":%0APP%}
+>publish stat/%topic%/RESULT {"ReactivePower":%RAP%}
+>publish stat/%topic%/RESULT {"Power":%0POW%}
+>publish stat/%topic%/RESULT {"Voltage":%0VOL%}
+>publish stat/%topic%/RESULT {"Current":%0CUR%}
 
Timer=0
 
endif
 
 
>E
 
;Executed when a Tasmota MQTT RESULT message is received
 
 
VOL=WebQuery#StatusSNS#ENERGY#Voltage
print Wert Volt %VOL%
 
CUR=WebQuery#StatusSNS#ENERGY#Current/1000
print Wert Current %CUR%
 
POW=WebQuery#StatusSNS#ENERGY#Power
print Wert Power %POW%
 
TOT=WebQuery#StatusSNS#ENERGY#Total
print Wert Total %TOT%
 
YES=WebQuery#StatusSNS#ENERGY#Yesterday
print Wert Yesterday %YES%
 
TOD=WebQuery#StatusSNS#ENERGY#Today
print Wert Today %TOD%
 
APP=WebQuery#StatusSNS#ENERGY#ApparentPower
print Wert Apparent Power %APP%
 
RAP=WebQuery#StatusSNS#ENERGY#ReactivePower
print Wert Reaktive Power %RAP%
 
 
>W
 
;The lines in this section are displayed in the web UI main page
 
          
Power{m} %2POW% W
Volt{m} %2VOL% V
Ampere{m} %2CUR% A
Total{m} %2TOT% 
Yesterday{m} %YES% 
Today{m} %2TOD% 
Apparent{m} %2APP% 
Reactive{m} %2RAP% 
 
 
 
#

                                      Ich habe es nochmal verglichen. Ich habe lediglich die Zeilen 21 und 45 angepasst.

                                      Ralla66 1 Reply Last reply Reply Quote 0
                                      • Ralla66
                                        Ralla66 Most Active @RalfTh last edited by Ralla66

                                        @ralfth sagte in Gosund SP111 mit Tasmota 13.2.0 Problem mit DP:

                                        Die IP für das websend ist die des ioBroker oder der Gosund?

                                        vom Gosund, das sieht doch gut aus 🙂

                                        Daten per IP websend kannst du von jedem Tasmota Gerät abfragen der die gleiche
                                        StatusSNS/Energy/xxx............................ hat.

                                        1 Reply Last reply Reply Quote 0
                                        • RalfTh
                                          RalfTh last edited by RalfTh

                                          @ralla66 Ok, dann habe ich es richtig gemacht.

                                          Allerdings stimmt der Inhalt nicht und diese Meldung scheint die Ursache zu sein:

                                          18:34:19.588 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}

                                          Steht auch in meinem letzten Post in der Konsolenausgabe.
                                          Gebe ich im Browser http://192.168.178.164/cm?cmnd=status 10 ein erhalte ich folgendes:
                                          {"StatusSNS":{"Time":"2023-11-15T18:37:01","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.556,"Yesterday":0.170,"Today":0.055,"Power":41,"ApparentPower":41,"ReactivePower":0,"Factor":1.00,"Voltage":229,"Current":0.181}}}

                                          In der Konsole sieht es folgend aus:

                                          18:38:48.972 MQT: tele/tasmota_B8D3E7/STATE = {"Time":"2023-11-15T18:38:48","Uptime":"0T12:01:26","UptimeSec":43286,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":4,"POWER":"ON","Wifi":{"AP":1,"SSId":"Palatina","BSSId":"5C:49:79:55:9E:DC","Channel":4,"Mode":"11n","RSSI":82,"Signal":-59,"LinkCount":1,"Downtime":"0T00:00:03"}}
18:38:48.984 MQT: tele/tasmota_B8D3E7/SENSOR = {"Time":"2023-11-15T18:38:48","ENERGY":{"TotalStartTime":"2020-06-30T13:38:42","Total":0.558,"Yesterday":0.170,"Today":0.057,"Period":1,"Power":42,"ApparentPower":42,"ReactivePower":0,"Factor":1.00,"Voltage":229,"Current":0.183}}
18:38:50.972 SCR: performs "websend [192.168.178.164] /cm?cmnd=status 10"
18:38:56.176 MQT: stat/tasmota_B8D3E7/RESULT = {"WebSend":"Connect failed"}
18:38:56.184 MQT: stat/tasmota_B8D3E7/RESULT = {"Total":0}
18:38:56.191 MQT: stat/tasmota_B8D3E7/RESULT = {"Yesterday":0}
18:38:56.199 MQT: stat/tasmota_B8D3E7/RESULT = {"Today":0}
18:38:56.206 MQT: stat/tasmota_B8D3E7/RESULT = {"ApparentPower":0}
18:38:56.213 MQT: stat/tasmota_B8D3E7/RESULT = {"ReactivePower":0.00}
18:38:56.221 MQT: stat/tasmota_B8D3E7/RESULT = {"Power":0}
18:38:56.228 MQT: stat/tasmota_B8D3E7/RESULT = {"Voltage":0}
18:38:56.235 MQT: stat/tasmota_B8D3E7/RESULT = {"Current":0}

                                          In den ersten beiden Zeilen siehst du die JSON-Inhalte, aber ab Zeile 5 sind alle Werte 0??!!

                                          Ich vermute das liegt am Connection failed in Zeile 4.

                                          Ralla66 1 Reply Last reply Reply Quote 0
                                          • Ralla66
                                            Ralla66 Most Active @RalfTh last edited by Ralla66

                                            @ralfth

                                            ja richtig, vermute da ist was falsch in Zeile 45 beim send
                                            Hattest du nicht 2 Gosund ? Dann nimm mal die andere IP

                                            RalfTh 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post

                                            Support us

                                            ioBroker
                                            Community Adapters
                                            Donate

                                            727
                                            Online

                                            31.7k
                                            Users

                                            79.8k
                                            Topics

                                            1.3m
                                            Posts

                                            4
                                            88
                                            5950
                                            Loading More Posts
                                            • Oldest to Newest
                                            • Newest to Oldest
                                            • Most Votes
                                            Reply
                                            • Reply as topic
                                            Log in to reply
                                            Community
                                            Impressum | Datenschutz-Bestimmungen | Nutzungsbedingungen
                                            The ioBroker Community 2014-2023
                                            logo