edit:

oh super das wars. Ich danke dir sehr

sudo ldconfig /usr/local/lib64

das kann doch nicht sein.

ich komme einfach nicht weiter. mittlerweile echt wütend

ich hatte z-way drauf. wurde erkennt und auch geräte wurden erkannt.

dann habe ich openhab2 drauf gehabt und auch hier wurde es erkannt. dank des menüs kann man einfach die punkte auswählen.

nur iobroker mist geht nicht. hatte niemand dieses razberry2 drauf laufen ?

ich bin jetzt so vorgegangen.

1. razberry2 platine ist abgesteckt.

2. neue image draufgetan auf die sd

3. in der konsole sudo nano /boot/cmdline.txteingegeben und die````
console=serial0,115200 entfernen

so sieht jetzt die zeile aus:

dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=620e8b20-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait

4.````
sudo nano /boot/config.txt
````aufgerufen

die drei Einträge eingefügt

dtoverlay=pi3-miniuart-bt
enable_uart=1
force_turbo=1

For more options and information see

http://rpf.io/configtxtreadme

Some settings may impact device functionality. See link above for details

uncomment if you get no picture on HDMI for a default "safe" mode

#hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible

and your display can output without overscan

#disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console

goes off screen, and negative if there is too much border

#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

uncomment to force a console size. By default it will be display's size minus

overscan.

#framebuffer_width=1280
#framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1
#hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in

DMT (computer monitor) modes

#hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or

no display

#config_hdmi_boost=4

uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

dtparam=audio=on

dtoverlay=pi3-miniuart-bt
enable_uart=1
force_turbo=1

5\. sudo reboot eingegeben und dabei die platine aufgesteckt.

es wird einfach nicht erkennt.

was mache ich falsch

host.ioBroker-RasPi 2017-11-03 15:17:55.126 error instance system.adapter.zwave.0 terminated with code 0 (OK)
host.ioBroker-RasPi 2017-11-03 15:17:55.126 error Caught by controller[0]: at Object.Module._extensions..js (module.js:579:10)
host.ioBroker-RasPi 2017-11-03 15:17:55.126 error Caught by controller[0]: at Module._compile (module.js:570:32)
host.ioBroker-RasPi 2017-11-03 15:17:55.126 error Caught by controller[0]: at Object. (/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/lib/openzwave-shared.js:26:19)
host.ioBroker-RasPi 2017-11-03 15:17:55.126 error Caught by controller[0]: at require (internal/module.js:20:19)
host.ioBroker-RasPi 2017-11-03 15:17:55.125 error Caught by controller[0]: at Module.require (module.js:497:17)
host.ioBroker-RasPi 2017-11-03 15:17:55.125 error Caught by controller[0]: at Function.Module._load (module.js:438:3)
host.ioBroker-RasPi 2017-11-03 15:17:55.125 error Caught by controller[0]: at tryModuleLoad (module.js:446:12)
host.ioBroker-RasPi 2017-11-03 15:17:55.125 error Caught by controller[0]: at Module.load (module.js:487:32)
host.ioBroker-RasPi 2017-11-03 15:17:55.125 error Caught by controller[0]: at Object.Module._extensions..node (module.js:597:18)
host.ioBroker-RasPi 2017-11-03 15:17:55.124 error Caught by controller[0]: at Error (native)
host.ioBroker-RasPi 2017-11-03 15:17:55.124 error Caught by controller[0]: Error: libopenzwave.so.1.4: cannot open shared object file: No such file or directory

@AlCalzone:

Brauchst nichts installieren, außer dem zwave-Adapter. Die ganze extra-Software belegt nur Netzwerk-Ports und muss wieder manuell entfernt werden.

Lediglich der Serialport muss umkonfiguriert werden:

sudo nano /boot/config.txt
-> folgendes einfügen bzw Auskommentierung entfernen:
dtoverlay=pi3-miniuart-bt
enable_uart=1
force_turbo=1

reboot
```` `  

ist es normal das nichts davon in der config.txt war?

ich habe die drei Einträge eingefügt

was folgt dann ?

gibt es niemanden der hier helfen kann ?

Hallo

ich habe mir jetzt razberry2 bestellt und es müsste morgen ankommen.

jetzt habe ich gelesen das wenn ich die platine aufstecke das Wlan nicht mehr benutzen kann?

stimmt das ? gibts da umwege?

Gibt es außerdem hier eine Anleitung was ich genau machen muss mit der Platine ?

anstecken und es wird erkannt ?

@andre:

@tscheinik:

haben uns überschnitten. darauf bin ich schon gekommen.

es hat jetzt geklappt. `

Du hattest jetzt nur sudo und unzip nachinstalliert, richtig?

Lass es mich bitte wissen ob das Einbinden des USB sticks gelingt, dann würde ich die Pakete mit in das Image aufnehmen.

MfG,

André

Gesendet mit Tapatalk `

ich habe es einmal geschafft bei z-wave einen usb port auszuwhälen. war aber kurz danach weg. ich kann nichtmal einen usb port aussuchen.

bei domoticz wird der stick erkannt.
2877_ashampoo_snap_2017.06.18_21h45m22s_001_.png
2877_ashampoo_snap_2017.06.18_21h45m50s_002_.png

ja sobald ich den stick bekomme werde ich es testen.

habe diesen stick Aeotec AEOEZW090-C Aeon Labs USB Stick

ja genau einmal sudo und einmal unzip

haben uns überschnitten. darauf bin ich schon gekommen.

es hat jetzt geklappt.

hallo

habe es installiert. aber bekomme trotzedem einen fehler. aber wohl was anderes

! ````
$ ./iobroker add zwave
npm install iobroker.zwave --unsafe-perm --production --prefix "/opt/iobroker" (System call)
sudo: unable to send audit message: Operation not permitteddebconf: unable to initialize frontend: Dialog
debconf: (No usable dialog-like program is installed, so the dialog based frontend cannot be used. at /usr/share/perl5/Debconf/FrontEnd/Dialog.pm line 76, <> line 1.)
debconf: falling back to frontend: Readline
debconf: unable to initialize frontend: Readline
debconf: (This frontend requires a controlling tty.)
debconf: falling back to frontend: Teletype
dpkg-preconfigure: unable to re-open stdin:
! % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed
! 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
100 125 0 125 0 0 160 0 --:--:-- --:--:-- --:--:-- 160
! 100 40742 0 40742 0 0 23720 0 --:--:-- 0:00:01 --:--:-- 23720
100 1709k 0 1709k 0 0 678k 0 --:--:-- 0:00:02 --:--:-- 2086k
! /bin/sh: 1: unzip: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15 if (!suppressException) throw e;
^
! Error: Command failed: unzip master.zip && rm master.zip
/bin/sh: 1: unzip: not found
! at checkExecSyncError (child_process.js:481:13)
at Object.execSync (child_process.js:521:13)
at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
at installOpenZwaveFromSource (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:109:3)
at installOpenZwave (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:103:3)
at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:26:7)
at Module._compile (module.js:570:32)
at Object.Module._extensions..js (module.js:579:10)
at Module.load (module.js:487:32)
at tryModuleLoad (module.js:446:12)
! npm
ERR! Linux 3.10.102
npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"npm ERR! node v6.11.0
npm ERR! npm v3.10.10
npm
ERR! code ELIFECYCLE
! npm
ERR! iobroker.zwave@0.6.0 preinstall: node lib/preinstall.js
npm ERR! Exit status 1
npm ERR!
npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR!
Make sure you have the latest version of node.js and npm installed.npm ERR!
If you do, this is most likely a problem with the iobroker.zwave package,npm
ERR! not with npm itself.npm ERR! Tell the author that this fails on your system:
npm ERR! node lib/preinstall.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR! npm bugs iobroker.zwave
npm ERR! Or if that isn't available, you can get their info via:
npm ERR!
npm owner ls iobroker.zwave
npm ERR! There is likely additional logging output above.
! npm ERR! Please include the following file with any support request:npm ERR! /opt/npm-debug.log
! host.DS415 install adapter zwave
npm install iobroker.zwave --unsafe-perm --production --prefix "/opt/iobroker" (System call)
sudo: unable to send audit message: Operation not permitted
% Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed
! 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
100 125 0 125 0 0 259 0 --:--:-- --:--:-- --:--:-- 259
! 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
46 1709k 46 787k 0 0 453k 0 0:00:03 0:00:01 0:00:02 760k
100 1709k 100 1709k 0 0 876k 0 0:00:01 0:00:01 --:--:-- 1369k
! /bin/sh: 1: unzip: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15 if (!suppressException) throw e;
^
! Error: Command failed: unzip master.zip && rm master.zip
/bin/sh: 1: unzip: not found
! at checkExecSyncError (child_process.js:481:13)
at Object.execSync (child_process.js:521:13)
at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
at installOpenZwaveFromSource (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:109:3)
at installOpenZwave (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:103:3)
at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:26:7)
at Module._compile (module.js:570:32)
at Object.Module._extensions..js (module.js:579:10)
at Module.load (module.js:487:32)
at tryModuleLoad (module.js:446:12)
! npm
ERR! Linux 3.10.102npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"
npm ERR! node v6.11.0
npm ERR! npm v3.10.10
npm ERR! code ELIFECYCLE
! npm
ERR! iobroker.zwave@0.6.0 preinstall: node lib/preinstall.jsnpm ERR! Exit status 1
npm ERR!
npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR! Make sure you have the latest version of node.js and npm installed.
npm ERR! If you do, this is most likely a problem with the iobroker.zwave package,
npm ERR!
not with npm itself.npm ERR! Tell the author that this fails on your system:
npm ERR! node lib/preinstall.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR! npm bugs iobroker.zwave
! npm ERR! Or if that isn't available, you can get their info via:npm ERR! npm owner ls iobroker.zwave
npm ERR! There is likely additional logging output above.
! npm ERR! Please include the following file with any support request:npm ERR! /opt/npm-debug.log
! host.DS415 install adapter zwave
npm install iobroker.zwave --unsafe-perm --production --prefix "/opt/iobroker" (System call)
sudo: unable to send audit message: Operation not permitted
% Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed
! 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
100 125 0 125 0 0 268 0 --:--:-- --:--:-- --:--:-- 268
! 8 1709k 8 137k 0 0 104k 0 0:00:16 0:00:01 0:00:15 104k
100 1709k 100 1709k 0 0 865k 0 0:00:01 0:00:01 --:--:-- 2381k
! /bin/sh: 1: unzip: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15 if (!suppressException) throw e;
^
! Error: Command failed: unzip master.zip && rm master.zip
/bin/sh: 1: unzip: not found
! at checkExecSyncError (child_process.js:481:13)
at Object.execSync (child_process.js:521:13)
at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
at installOpenZwaveFromSource (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:109:3)
at installOpenZwave (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:103:3)
at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:26:7)
at Module._compile (module.js:570:32)
at Object.Module._extensions..js (module.js:579:10)
at Module.load (module.js:487:32)
at tryModuleLoad (module.js:446:12)
! npm
ERR! Linux 3.10.102npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"
npm ERR!
node v6.11.0npm ERR! npm v3.10.10
npm ERR! code ELIFECYCLE
! npm ERR! iobroker.zwave@0.6.0 preinstall: node lib/preinstall.jsnpm ERR! Exit status 1
npm ERR!
npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR! Make sure you have the latest version of node.js and npm installed.
npm ERR! If you do, this is most likely a problem with the iobroker.zwave package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR! node lib/preinstall.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR! npm bugs iobroker.zwave
npm ERR! Or if that isn't available, you can get their info via:
npm ERR! npm owner ls iobroker.zwave
npm ERR! There is likely additional logging output above.
! npm ERR! Please include the following file with any support request:npm ERR! /opt/npm-debug.log
! host.DS415 install adapter zwave
ERROR: host.DS415 Cannot install zwave
ERROR: process exited with code 13</anonymous></anonymous></anonymous>

habe jetzt mal apt-get install unzip ins terminal eingegeben. versuche jetzt nochmal

edit:

es hat geklappt

Hallo bin ganz neu hier.

habe auf der 415+ mit docker iobroker zum laufen bekommen. da in den nächsten tagen ein z-wave usb stick kommt wollt eich schon mal den z-wave adapter installieren.

klappt aber nicht.

hat einer ahnung was der fehler ist ?

! ````
$ ./iobroker add zwave
npm install iobroker.zwave --unsafe-perm --production --prefix "/opt/iobroker" (System call)
/bin/sh: 1: sudo: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15 if (!suppressException) throw e;
^
! Error: Command failed: sudo apt-get install libudev-dev -y
/bin/sh: 1: sudo: not found
! at checkExecSyncError (child_process.js:481:13)
at Object.execSync (child_process.js:521:13)
at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:25:7)
at Module._compile (module.js:570:32)
at Object.Module._extensions..js (module.js:579:10)
at Module.load (module.js:487:32)
at tryModuleLoad (module.js:446:12)
at Function.Module._load (module.js:438:3)
at Module.runMain (module.js:604:10)
! npm
ERR! Linux 3.10.102npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"
npm ERR! node v6.11.0
npm ERR! npm v3.10.10
npm ERR! code ELIFECYCLE
! npm ERR! iobroker.zwave@0.6.0 preinstall: node lib/preinstall.jsnpm ERR! Exit status 1
npm ERR!
npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR! Make sure you have the latest version of node.js and npm installed.
npm ERR! If you do, this is most likely a problem with the iobroker.zwave package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR! node lib/preinstall.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR! npm bugs iobroker.zwave
npm ERR! Or if that isn't available, you can get their info via:
npm ERR! npm owner ls iobroker.zwave
npm ERR! There is likely additional logging output above.
! npm ERR! Please include the following file with any support request:npm ERR! /opt/npm-debug.log
! host.DS415 install adapter zwave
npm install iobroker.zwave --unsafe-perm --production --prefix "/opt/iobroker" (System call)
/bin/sh: 1: sudo: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15 if (!suppressException) throw e;
^
! Error: Command failed: sudo apt-get install libudev-dev -y
/bin/sh: 1: sudo: not found
! at checkExecSyncError (child_process.js:481:13)
at Object.execSync (child_process.js:521:13)
at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:25:7)
at Module._compile (module.js:570:32)
at Object.Module._extensions..js (module.js:579:10)
at Module.load (module.js:487:32)
at tryModuleLoad (module.js:446:12)
at Function.Module._load (module.js:438:3)
at Module.runMain (module.js:604:10)
! npm ERR! Linux 3.10.102
npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"npm ERR! node v6.11.0
! npm ERR! npm v3.10.10npm ERR! code ELIFECYCLE
! npm ERR! iobroker.zwave@0.6.0 preinstall: node lib/preinstall.jsnpm ERR! Exit status 1
! npm ERR! npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR! Make sure you have the latest version of node.js and npm installed.
npm
ERR! If you do, this is most likely a problem with the iobroker.zwave package,npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR! node lib/preinstall.js
npm ERR!
You can get information on how to open an issue for this project with:npm ERR!
npm bugs iobroker.zwavenpm ERR! Or if that isn't available, you can get their info via:
npm ERR! npm owner ls iobroker.zwave
npm ERR! There is likely additional logging output above.
! npm ERR!
Please include the following file with any support request:npm ERR! /opt/npm-debug.log
! host.DS415 install adapter zwave
npm install iobroker.zwave --unsafe-perm --production --prefix "/opt/iobroker" (System call)
/bin/sh: 1: sudo: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15 if (!suppressException) throw e;
^
! Error: Command failed: sudo apt-get install libudev-dev -y
/bin/sh: 1: sudo: not found
! at checkExecSyncError (child_process.js:481:13)
at Object.execSync (child_process.js:521:13)
at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:25:7)
at Module._compile (module.js:570:32)
at Object.Module._extensions..js (module.js:579:10)
at Module.load (module.js:487:32)
at tryModuleLoad (module.js:446:12)
at Function.Module._load (module.js:438:3)
at Module.runMain (module.js:604:10)
! npm
ERR! Linux 3.10.102npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"
npm
ERR! node v6.11.0
npm ERR! npm v3.10.10npm ERR! code ELIFECYCLE
! npm ERR! iobroker.zwave@0.6.0 preinstall: node lib/preinstall.jsnpm ERR! Exit status 1
npm ERR!
npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR! Make sure you have the latest version of node.js and npm installed.
npm ERR! If you do, this is most likely a problem with the iobroker.zwave package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR! node lib/preinstall.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR! npm bugs iobroker.zwave
npm ERR! Or if that isn't available, you can get their info via:
npm ERR! npm owner ls iobroker.zwave
npm ERR! There is likely additional logging output above.
! npm ERR! Please include the following file with any support request:
npm ERR! /opt/npm-debug.log
! host.DS415 install adapter zwave
ERROR: host.DS415 Cannot install zwave
ERROR: process exited with code 13</anonymous></anonymous></anonymous>

Hallo

ich habe iobroker auf der Synology 415+ mit docker installiert und schon hue und hanrmony hinzugefügt.

jetzt habe ich mir heute einen Z-Wave USB Stick bestellt. Wollte jetzt den Z-wave Adapter installieren.

Bekomme aber die Fehlermeldung. Könnt ihr mir sagen was da schief gelaufen ist ?

$ ./iobroker add zwave
npm install iobroker.zwave --unsafe-perm  --production --prefix "/opt/iobroker" (System call)
/bin/sh: 1: sudo: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15    if (!suppressException) throw e;
                            ^

Error: Command failed: sudo apt-get install libudev-dev -y
/bin/sh: 1: sudo: not found

    at checkExecSyncError (child_process.js:481:13)
    at Object.execSync (child_process.js:521:13)
    at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
    at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:25:7)
    at Module._compile (module.js:570:32)
    at Object.Module._extensions..js (module.js:579:10)
    at Module.load (module.js:487:32)
    at tryModuleLoad (module.js:446:12)
    at Function.Module._load (module.js:438:3)
    at Module.runMain (module.js:604:10)

npm
 ERR! Linux 3.10.102
npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"npm ERR! node v6.11.0
npm ERR! npm  v3.10.10
npm ERR! code ELIFECYCLE

npm ERR! iobroker.zwave@0.6.0 preinstall: `node lib/preinstall.js`npm ERR! Exit status 1
npm ERR! 
npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR! Make sure you have the latest version of node.js and npm installed.
npm ERR! If you do, this is most likely a problem with the iobroker.zwave package,
npm ERR!
 not with npm itself.npm ERR! Tell the author that this fails on your system:
npm ERR!     node lib/preinstall.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR!     npm bugs iobroker.zwave
npm ERR! Or if that isn't available, you can get their info via:
npm ERR!
     npm owner ls iobroker.zwavenpm 
ERR! There is likely additional logging output above.

npm ERR! Please include the following file with any support request:npm ERR!     /opt/npm-debug.log

host.DS415 install adapter zwave
npm install iobroker.zwave --unsafe-perm  --production --prefix "/opt/iobroker" (System call)
/bin/sh: 1: sudo: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15    if (!suppressException) throw e;
                            ^

Error: Command failed: sudo apt-get install libudev-dev -y
/bin/sh: 1: sudo: not found

    at checkExecSyncError (child_process.js:481:13)
    at Object.execSync (child_process.js:521:13)
    at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
    at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:25:7)
    at Module._compile (module.js:570:32)
    at Object.Module._extensions..js (module.js:579:10)
    at Module.load (module.js:487:32)
    at tryModuleLoad (module.js:446:12)
    at Function.Module._load (module.js:438:3)
    at Module.runMain (module.js:604:10)

npm
 ERR! Linux 3.10.102npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"
npm ERR! 
node v6.11.0npm ERR! npm  v3.10.10
npm ERR! code ELIFECYCLE

npm 
ERR! iobroker.zwave@0.6.0 preinstall: `node lib/preinstall.js`npm ERR! Exit status 1
npm ERR!
 npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR! Make sure you have the latest version of node.js and npm installed.
npm ERR! If you do, this is most likely a problem with the iobroker.zwave package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR!     node lib/preinstall.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR!     npm bugs iobroker.zwave
npm ERR! Or if that isn't available, you can get their info via:
npm ERR!     npm owner ls iobroker.zwave
npm ERR! There is likely additional logging output above.

npm ERR! Please include the following file with any support request:npm ERR!     /opt/npm-debug.log

host.DS415 install adapter zwave
npm install iobroker.zwave --unsafe-perm  --production --prefix "/opt/iobroker" (System call)
/bin/sh: 1: sudo: not found
/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:15    if (!suppressException) throw e;
                            ^

Error: Command failed: sudo apt-get install libudev-dev -y
/bin/sh: 1: sudo: not found

    at checkExecSyncError (child_process.js:481:13)
    at Object.execSync (child_process.js:521:13)
    at doScript (/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:12:15)
    at Object. <anonymous>(/opt/iobroker/node_modules/.staging/iobroker.zwave-936e120a/lib/preinstall.js:25:7)
    at Module._compile (module.js:570:32)
    at Object.Module._extensions..js (module.js:579:10)
    at Module.load (module.js:487:32)
    at tryModuleLoad (module.js:446:12)
    at Function.Module._load (module.js:438:3)
    at Module.runMain (module.js:604:10)

npm ERR! Linux 3.10.102
npm ERR! argv "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--unsafe-perm" "--production" "--prefix" "/opt/iobroker"npm ERR! node v6.11.0
npm ERR! npm  v3.10.10

npm ERR! code ELIFECYCLE

npm ERR! iobroker.zwave@0.6.0 preinstall: `node lib/preinstall.js`npm ERR! Exit status 1
npm ERR! 
npm ERR! Failed at the iobroker.zwave@0.6.0 preinstall script 'node lib/preinstall.js'.
npm ERR! Make sure you have the latest version of node.js and npm installed.
npm ERR! If you do, this is most likely a problem with the iobroker.zwave package,
npm ERR! not with npm itself.

npm ERR! Tell the author that this fails on your system:npm ERR!     node lib/preinstall.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR!     npm bugs iobroker.zwave

npm ERR! Or if that isn't available, you can get their info via:npm ERR!     npm owner ls iobroker.zwave
npm ERR! There is likely additional logging output above.

npm ERR! Please include the following file with any support request:npm ERR!     /opt/npm-debug.log

host.DS415 install adapter zwave
ERROR: host.DS415 Cannot install zwave
ERROR: process exited with code 13</anonymous></anonymous></anonymous>