Скрипт для счётчика

smoker_vvo

А вот тут и возникла проблема… Не заливаются скетчи.... любая попытка заканчивается ошибкой закачки скетча.... И бешеный светодиод......

instalator

~~@smoker_vvo:~~

А вот тут и возникла проблема… Не заливаются скетчи.... любая попытка заканчивается ошибкой закачки скетча.... И бешеный светодиод...... `
Прошей загрузчик оптибут или шей ее через программатор

smoker_vvo

Ну тогда давай рекомендации что и как делать, через что прошивать, у меня голова опухла от обилия информации о прошивке оптибута

instalator

~~@smoker_vvo:~~

Ну тогда давай рекомендации что и как делать, через что прошивать, у меня голова опухла от обилия информации о прошивке оптибута `

http://blog.instalator.ru/archives/798

smoker_vvo

Доброго времени…

Появилось время заниматься проектом дальше. и вот какие проблемы, если с WDT я поступил грубо, просто закоментил его, то с ethernetom вообще ни чего не могу понять. Учитывая что у тебя была другая карта, использую библиотеку для своей.... и ничего не работает....

1. ping - ни чего нет

2. соответсвенно в IOBе то же тишина.

заливал другие скетчи - с сетевой проблем нет.

вот код :

! ```
#include <spi.h> #include <ethernet.h> #include <pubsubclient.h> #include <eeprom.h> //#include <avr wdt.h=""> ! #define PWR_CTRL A2 //Контроль напряжения #define LED 9 //Светодиод #define CHK_ADR 100 #define CNT_ADR 10 #define PWR_ADR 20 #define POLL_ADR 30 #define RATIO_ADR 40 ! const char* topic_err = "myhome/elcounter/error"; const char* topic_cnt = "myhome/elcounter/count"; const char* topic_pwr = "myhome/elcounter/power"; const char* topic_amp = "myhome/elcounter/amp"; const char* topic_save = "myhome/elcounter/save"; const char* topic_correction = "myhome/elcounter/correction"; const char* topic_connection = "myhome/elcounter/connection"; const char* topic_ip = "myhome/elcounter/config/ip"; const char* topic_polling = "myhome/elcounter/config/polling"; const char* topic_bounce = "myhome/elcounter/config/bounce"; const char* topic_num = "myhome/elcounter/config/num"; const char* topic_reset = "myhome/elcounter/config/reset"; const char* topic_raw = "myhome/elcounter/RAW"; const char* subscr = "myhome/elcounter/#"; ! byte mac[] = { 0xDE, 0xAD, 0xBE, 0xE4, 0xDE, 0x35 }; byte ip[] = { 192, 168, 0, 89}; byte server[] = { 192, 168, 0, 15}; ! unsigned long cnt = 0; unsigned long prev_cnt = 2; unsigned long pwr = 0; unsigned long prev_pwr = 2; int amp = 0; int prev_amp = 2; int num = 0; int prev_num; int bounce = 10; int prev_bounce; int chk = 0; int chk_S = 0; unsigned long prevMillis = 0; unsigned long prevMillis_cnt = 0; int poll = 5000; bool error = 0; String cmd = ""; bool strComplete = false; char buf [50]; char buffer[100]; char s[16]; ! //////////////////////////////////////////////////////////////////////////// void callback(char* topic, byte* payload, unsigned int length) { payload[length] = '\0'; String strTopic = String(topic); String strPayload = String((char*)payload); callback_iobroker(strTopic, strPayload); } ! EthernetClient ethClient; PubSubClient client(server, 1883, callback, ethClient); ! void setup() { MCUSR = 0; // wdt_disable(); Serial.println("WDT_disable"); cmd.reserve(100); delay(10000); Serial.begin(57600); Serial.println("Starting......"); ! if (EEPROM.read(1) != 99) { //Если первый запуск EEPROM.write(1, 99); for (int i = 0 ; i < 4; i++) { EEPROM.write(110 + i, ip[i]); } for (int i = 0 ; i < 4; i++) { EEPROM.write(120 + i, server[i]); } } else { chk = EEPROMReadInt(CHK_ADR); cnt = EEPROMReadLong(CNT_ADR); poll = EEPROMReadInt(POLL_ADR); chk_S = poll - 500; if (chk != chk_S) { error = 2; } for (int i = 0; i < 4; i++) { ip[i] = EEPROM.read(110 + i); } for (int i = 0; i < 4; i++) { server[i] = EEPROM.read(120 + i); } } ! pinMode(LED, OUTPUT); ! // client.setServer(server, 1883); // client.setCallback(callback); Ethernet.begin(mac, ip); delay(200); //wdt_enable(WDTO_8S); Serial.println("WDTO_8S"); if (client.connect("elcounter")) { digitalWrite(LED, LOW); Public(); } } ! void serialEvent() { while (Serial.available() > 0) { char inChar = (char)Serial.read(); cmd += inChar; if (inChar == '\n') { strComplete = true; } } } ! void callback_iobroker(String strTopic, String strPayload) { if (strTopic == topic_correction) { cnt = atol((strPayload).c_str()); Serial.print("SC"); Serial.println(cnt); client.publish(topic_correction, "0"); } else if (strTopic == topic_save) { if (strPayload == "true") { Serial.println("SS"); save(); client.publish(topic_save, "false"); } } else if (strTopic == topic_polling) { poll = strPayload.toInt(); if (poll < 1000) { poll = 1000; } else if (poll > 32767) { poll = 32767; } EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации client.publish(topic_polling, IntToChar(poll)); } else if (strTopic == topic_reset) { if (strPayload == "true") { client.publish(topic_reset, "false"); // reboot(); Serial.println("Reboot"); } } else if (strTopic == topic_bounce) { bounce = strPayload.toInt(); if (bounce < 0) { bounce = 0; } else if (bounce > 10000) { bounce = 10000; } Serial.print("SB"); Serial.println(bounce); client.publish(topic_bounce, IntToChar(bounce)); } else if (strTopic == topic_num) { num = strPayload.toInt(); if (num < 0) { num = 0; } else if (num > 32767) { num = 32767; } Serial.print("SN"); Serial.println(num); client.publish(topic_num, IntToChar(num)); } } ! void save() { chk = poll - 500; EEPROMWriteLong(CNT_ADR, cnt); //Пишем показания счетчика в eeprom из переменной EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации EEPROMWriteInt(CHK_ADR, chk); //чек } ! void reboot() { save(); delay(500); // wdt_enable(WDTO_1S); Serial.println("void reboot"); for (;;) {} } ! char* StrToChar (String str) { int length = str.length(); str.toCharArray(buf, length + 1); return buf; } ! void EEPROMWriteLong(int p_address, unsigned long p_value) { byte four = (p_value & 0xFF); byte three = ((p_value >> 8) & 0xFF); byte two = ((p_value >> 16) & 0xFF); byte one = ((p_value >> 24) & 0xFF); EEPROM.write(p_address, four); EEPROM.write(p_address + 1, three); EEPROM.write(p_address + 2, two); EEPROM.write(p_address + 3, one); } ! unsigned long EEPROMReadLong(int p_address) { long four = EEPROM.read(p_address); long three = EEPROM.read(p_address + 1); long two = EEPROM.read(p_address + 2); long one = EEPROM.read(p_address + 3); return ((four << 0) & 0xFF) + ((three << 8) & 0xFFFF) + ((two << 16) & 0xFFFFFF) + ((one << 24) & 0xFFFFFFFF); } ! void EEPROMWriteInt(int p_address, int p_value) { byte lowByte = ((p_value >> 0) & 0xFF); byte highByte = ((p_value >> 8) & 0xFF); EEPROM.write(p_address, lowByte); EEPROM.write(p_address + 1, highByte); } unsigned int EEPROMReadInt(int p_address) { byte lowByte = EEPROM.read(p_address); byte highByte = EEPROM.read(p_address + 1); return ((lowByte << 0) & 0xFF) + ((highByte << 8) & 0xFF00); } ! char* IntToChar (unsigned long a) { sprintf(buf, "%lu", a); return buf; } ! void Public() { sprintf(s, "%d.%d.%d.%d", ip[0], ip[1], ip[2], ip[3]); client.publish(topic_err, " "); client.publish(topic_cnt, IntToChar(cnt)); client.publish(topic_pwr, IntToChar(pwr)); client.publish(topic_amp, IntToChar(amp)); client.publish(topic_save, "false"); client.publish(topic_correction, "0"); client.publish(topic_connection, "true"); client.publish(topic_ip, s); client.publish(topic_polling, IntToChar(poll)); client.publish(topic_bounce, IntToChar(bounce)); client.publish(topic_num, IntToChar(num)); client.publish(topic_reset, "false"); client.subscribe(subscr); } void reconnect() { int a = 0; while (!client.connected()) { a++; digitalWrite(LED, !digitalRead(LED)); //wdt_reset(); Serial.println("WDT reset"); if (client.connect("elcounter")) { digitalWrite(LED, LOW); Public(); } else { delay(10000); } if (a >= 10) { // wdt_enable(WDTO_1S); Serial.println("WDTO_1S"); } } } ! void loop() { // wdt_reset(); Serial.println("WDT_reset"); client.loop(); if (!client.connected()) { reconnect(); } ! if (analogRead(PWR_CTRL) < 1000) { digitalWrite(LED, LOW); save(); delay(10000); } ! if (strComplete) { digitalWrite(LED, !digitalRead(LED)); cmd.toCharArray(buffer, 100); cnt = atoi(strtok(buffer, ";")); pwr = atoi(strtok(NULL, ";")); amp = atoi(strtok(NULL, ";")); bounce = atoi(strtok(NULL, ";")); num = atoi(strtok(NULL, ";")); error = atoi(strtok(NULL, ";")); client.publish(topic_raw, StrToChar(cmd)); cmd = ""; strComplete = false; } ! if (millis() - prevMillis >= poll) { // wdt_reset(); Serial.println("WDT_reset"); prevMillis = millis(); if (cnt != prev_cnt || pwr != prev_pwr || amp != prev_amp) { prev_cnt = cnt; prev_pwr = pwr; prev_amp = amp; client.publish(topic_cnt, IntToChar(cnt)); client.publish(topic_pwr, IntToChar(pwr)); client.publish(topic_amp, IntToChar(amp)); } if (num != prev_num || bounce != prev_bounce) { prev_num = num; prev_bounce = bounce; client.publish(topic_num, IntToChar(num)); client.publish(topic_bounce, IntToChar(bounce)); } if (error > 0) { client.publish(topic_err, "err"); } else { client.publish(topic_err, " "); } } }</avr></eeprom.h></pubsubclient.h></ethernet.h></spi.h>
код с моими правками[/i][/i][/i][/i]

instalator

~~@smoker_vvo:~~

Доброго времени…

Появилось время заниматься проектом дальше. и вот какие проблемы, если с WDT я поступил грубо, просто закоментил его, то с ethernetom вообще ни чего не могу понять. Учитывая что у тебя была другая карта, использую библиотеку для своей.... и ничего не работает....

1. ping - ни чего нет

2. соответсвенно в IOBе то же тишина.

заливал другие скетчи - с сетевой проблем нет.

вот код :

! `#include <spi.h> #include <ethernet.h> #include <pubsubclient.h> #include <eeprom.h> //#include <avr wdt.h=""> ! #define PWR_CTRL A2 //Контроль напряжения #define LED 9 //Светодиод #define CHK_ADR 100 #define CNT_ADR 10 #define PWR_ADR 20 #define POLL_ADR 30 #define RATIO_ADR 40 ! const char* topic_err = "myhome/elcounter/error"; const char* topic_cnt = "myhome/elcounter/count"; const char* topic_pwr = "myhome/elcounter/power"; const char* topic_amp = "myhome/elcounter/amp"; const char* topic_save = "myhome/elcounter/save"; const char* topic_correction = "myhome/elcounter/correction"; const char* topic_connection = "myhome/elcounter/connection"; const char* topic_ip = "myhome/elcounter/config/ip"; const char* topic_polling = "myhome/elcounter/config/polling"; const char* topic_bounce = "myhome/elcounter/config/bounce"; const char* topic_num = "myhome/elcounter/config/num"; const char* topic_reset = "myhome/elcounter/config/reset"; const char* topic_raw = "myhome/elcounter/RAW"; const char* subscr = "myhome/elcounter/#"; ! byte mac[] = { 0xDE, 0xAD, 0xBE, 0xE4, 0xDE, 0x35 }; byte ip[] = { 192, 168, 0, 89}; byte server[] = { 192, 168, 0, 15}; ! unsigned long cnt = 0; unsigned long prev_cnt = 2; unsigned long pwr = 0; unsigned long prev_pwr = 2; int amp = 0; int prev_amp = 2; int num = 0; int prev_num; int bounce = 10; int prev_bounce; int chk = 0; int chk_S = 0; unsigned long prevMillis = 0; unsigned long prevMillis_cnt = 0; int poll = 5000; bool error = 0; String cmd = ""; bool strComplete = false; char buf [50]; char buffer[100]; char s[16]; ! //////////////////////////////////////////////////////////////////////////// void callback(char* topic, byte* payload, unsigned int length) { payload[length] = '\0'; String strTopic = String(topic); String strPayload = String((char*)payload); callback_iobroker(strTopic, strPayload); } ! EthernetClient ethClient; PubSubClient client(server, 1883, callback, ethClient); ! void setup() { MCUSR = 0; // wdt_disable(); Serial.println("WDT_disable"); cmd.reserve(100); delay(10000); Serial.begin(57600); Serial.println("Starting......"); ! if (EEPROM.read(1) != 99) { //Если первый запуск EEPROM.write(1, 99); for (int i = 0 ; i < 4; i++) { EEPROM.write(110 + i, ip[i]); } for (int i = 0 ; i < 4; i++) { EEPROM.write(120 + i, server[i]); } } else { chk = EEPROMReadInt(CHK_ADR); cnt = EEPROMReadLong(CNT_ADR); poll = EEPROMReadInt(POLL_ADR); chk_S = poll - 500; if (chk != chk_S) { error = 2; } for (int i = 0; i < 4; i++) { ip[i] = EEPROM.read(110 + i); } for (int i = 0; i < 4; i++) { server[i] = EEPROM.read(120 + i); } } ! pinMode(LED, OUTPUT); ! // client.setServer(server, 1883); // client.setCallback(callback); Ethernet.begin(mac, ip); delay(200); //wdt_enable(WDTO_8S); Serial.println("WDTO_8S"); if (client.connect("elcounter")) { digitalWrite(LED, LOW); Public(); } } ! void serialEvent() { while (Serial.available() > 0) { char inChar = (char)Serial.read(); cmd += inChar; if (inChar == '\n') { strComplete = true; } } } ! void callback_iobroker(String strTopic, String strPayload) { if (strTopic == topic_correction) { cnt = atol((strPayload).c_str()); Serial.print("SC"); Serial.println(cnt); client.publish(topic_correction, "0"); } else if (strTopic == topic_save) { if (strPayload == "true") { Serial.println("SS"); save(); client.publish(topic_save, "false"); } } else if (strTopic == topic_polling) { poll = strPayload.toInt(); if (poll < 1000) { poll = 1000; } else if (poll > 32767) { poll = 32767; } EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации client.publish(topic_polling, IntToChar(poll)); } else if (strTopic == topic_reset) { if (strPayload == "true") { client.publish(topic_reset, "false"); // reboot(); Serial.println("Reboot"); } } else if (strTopic == topic_bounce) { bounce = strPayload.toInt(); if (bounce < 0) { bounce = 0; } else if (bounce > 10000) { bounce = 10000; } Serial.print("SB"); Serial.println(bounce); client.publish(topic_bounce, IntToChar(bounce)); } else if (strTopic == topic_num) { num = strPayload.toInt(); if (num < 0) { num = 0; } else if (num > 32767) { num = 32767; } Serial.print("SN"); Serial.println(num); client.publish(topic_num, IntToChar(num)); } } ! void save() { chk = poll - 500; EEPROMWriteLong(CNT_ADR, cnt); //Пишем показания счетчика в eeprom из переменной EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации EEPROMWriteInt(CHK_ADR, chk); //чек } ! void reboot() { save(); delay(500); // wdt_enable(WDTO_1S); Serial.println("void reboot"); for (;;) {} } ! char* StrToChar (String str) { int length = str.length(); str.toCharArray(buf, length + 1); return buf; } ! void EEPROMWriteLong(int p_address, unsigned long p_value) { byte four = (p_value & 0xFF); byte three = ((p_value >> 8) & 0xFF); byte two = ((p_value >> 16) & 0xFF); byte one = ((p_value >> 24) & 0xFF); EEPROM.write(p_address, four); EEPROM.write(p_address + 1, three); EEPROM.write(p_address + 2, two); EEPROM.write(p_address + 3, one); } ! unsigned long EEPROMReadLong(int p_address) { long four = EEPROM.read(p_address); long three = EEPROM.read(p_address + 1); long two = EEPROM.read(p_address + 2); long one = EEPROM.read(p_address + 3); return ((four << 0) & 0xFF) + ((three << 8) & 0xFFFF) + ((two << 16) & 0xFFFFFF) + ((one << 24) & 0xFFFFFFFF); } ! void EEPROMWriteInt(int p_address, int p_value) { byte lowByte = ((p_value >> 0) & 0xFF); byte highByte = ((p_value >> 8) & 0xFF); EEPROM.write(p_address, lowByte); EEPROM.write(p_address + 1, highByte); } unsigned int EEPROMReadInt(int p_address) { byte lowByte = EEPROM.read(p_address); byte highByte = EEPROM.read(p_address + 1); return ((lowByte << 0) & 0xFF) + ((highByte << 8) & 0xFF00); } ! char* IntToChar (unsigned long a) { sprintf(buf, "%lu", a); return buf; } ! void Public() { sprintf(s, "%d.%d.%d.%d", ip[0], ip[1], ip[2], ip[3]); client.publish(topic_err, " "); client.publish(topic_cnt, IntToChar(cnt)); client.publish(topic_pwr, IntToChar(pwr)); client.publish(topic_amp, IntToChar(amp)); client.publish(topic_save, "false"); client.publish(topic_correction, "0"); client.publish(topic_connection, "true"); client.publish(topic_ip, s); client.publish(topic_polling, IntToChar(poll)); client.publish(topic_bounce, IntToChar(bounce)); client.publish(topic_num, IntToChar(num)); client.publish(topic_reset, "false"); client.subscribe(subscr); } void reconnect() { int a = 0; while (!client.connected()) { a++; digitalWrite(LED, !digitalRead(LED)); //wdt_reset(); Serial.println("WDT reset"); if (client.connect("elcounter")) { digitalWrite(LED, LOW); Public(); } else { delay(10000); } if (a >= 10) { // wdt_enable(WDTO_1S); Serial.println("WDTO_1S"); } } } ! void loop() { // wdt_reset(); Serial.println("WDT_reset"); client.loop(); if (!client.connected()) { reconnect(); } ! if (analogRead(PWR_CTRL) < 1000) { digitalWrite(LED, LOW); save(); delay(10000); } ! if (strComplete) { digitalWrite(LED, !digitalRead(LED)); cmd.toCharArray(buffer, 100); cnt = atoi(strtok(buffer, ";")); pwr = atoi(strtok(NULL, ";")); amp = atoi(strtok(NULL, ";")); bounce = atoi(strtok(NULL, ";")); num = atoi(strtok(NULL, ";")); error = atoi(strtok(NULL, ";")); client.publish(topic_raw, StrToChar(cmd)); cmd = ""; strComplete = false; } ! if (millis() - prevMillis >= poll) { // wdt_reset(); Serial.println("WDT_reset"); prevMillis = millis(); if (cnt != prev_cnt || pwr != prev_pwr || amp != prev_amp) { prev_cnt = cnt; prev_pwr = pwr; prev_amp = amp; client.publish(topic_cnt, IntToChar(cnt)); client.publish(topic_pwr, IntToChar(pwr)); client.publish(topic_amp, IntToChar(amp)); } if (num != prev_num || bounce != prev_bounce) { prev_num = num; prev_bounce = bounce; client.publish(topic_num, IntToChar(num)); client.publish(topic_bounce, IntToChar(bounce)); } if (error > 0) { client.publish(topic_err, "err"); } else { client.publish(topic_err, " "); } } }</avr></eeprom.h></pubsubclient.h></ethernet.h></spi.h>` код с моими правками Вроде все норм по сети, в логе тишина? ! byte ip[] = { 192, 168, 0, 89}; айпи самой ардуины ! byte server[] = { 192, 168, 0, 15}; айпи mqtt сервера[/i][/i][/i][/i] `

smoker_vvo

А не может быть связанным как то с удаленным конфигом сетевого адреса??

const char* topic_ip = "myhome/elcounter/config/ip";

Заливал этот код в Дуню - все работает…

! ```
`#include <spi.h> // Ethernet shield
#include <ethernet.h> // Ethernet shield
#include <pubsubclient.h> // MQTT
#include <servo.h>
#include <dht.h>
#include <onewire.h>
#include <dallastemperature.h>
Servo servo;
! byte mac[] = { 0xC1, 0x7C, 0x38, 0x41, 0x89, 0x35 };
byte server[] = { 192, 168, 0, 11 }; //IP Брокера
byte ip[] = { 192, 168, 0, 89 }; //IP Клиента (Arduino)
! ////////////////////////////////////////////////////////////////////////////
void callback(char* topic, byte* payload, unsigned int length) {
payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
String strTopic = String(topic);
String strPayload = String((char*)payload);
// Serial.println(strPayload);
callback_iobroker(strTopic, strPayload);
}
! EthernetClient ethClient;
PubSubClient client(server, 1883, callback, ethClient);
#define id_connect "myhome-temp"
#define id_connect "myhome-status"
#define Prefix_subscribe "myhome/Temp/"
#define Prefix_subscribe "myhome/Status/"
! ///////////////Объявляем порты ввода-вывода
#define ServoPin 3 //Порт к которому подключен сервопривод
! const int start_DI_pin []= {2, 4, 5}; // Порты Ввода
int n_DI_pin = sizeof(start_DI_pin) / sizeof(start_DI_pin[0])-1; //Вычисляем длинну массива
! const int start_DO_pin []= {6, 7}; //Порты Вывода
int n_DO_pin = sizeof(start_DO_pin) / sizeof(start_DO_pin[0])-1; //Вычисляем длинну массива
! int DI[] = {0, 0, 0};
int old_DI[] = {0, 0, 0};
! ///////////////////////////Переменные для работы с освещением//////////////////////////////////////
int ServoAngle = 100; //Угол сервопривода при включении
int flag = 0;
int flag2 = 0;
int pause = 0;
! //------------------------------------------- Sensors -------------------------------------------//
const int MQ7_Pin = A0; // Куда подключили MQ7
//int MQ7Value = 0;
int MQ7Value = analogRead(MQ7_Pin);

const int foto_Pin = A1; // устанавливаем входную ногу для Фоторезистора
//unsigned int fotoValue = 0; // цифровое значение фоторезистора
unsigned int fotoValue = analogRead(foto_Pin);

! #define ONE_WIRE_BUS 8
//#define TEMPERATURE_PRECISION 9
OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature DS_sensors(&oneWire);
// 28 80 E9 3A 04 00 00 10
//T0:28 88 AD D7 02 00 00 42
//T1:28 14 A5 D7 02 00 00 B0
//T2:28 72 26 7B 04 00 00 2E
//T3:28 CA 1A 3B 04 00 00 CD
//T4:28 E6 D5 D7 02 00 00 C1
//T5:28 16 B4 7A 04 00 00 8A
//T6:28 2B 86 D7 02 00 00 CF
//T7:28 AB 9D D7 02 00 00 29
DeviceAddress addr_T1 = { 0x28, 0x80, 0xE9, 0x3A, 0x4, 0x0, 0x0, 0x10 };//кладовка
DeviceAddress addr_T2 = { 0x28, 0x88, 0xAD, 0xD7, 0x2, 0x0, 0x0, 0x42 };//кухня
DeviceAddress addr_T3 = { 0x28, 0x14, 0xA5, 0xD7, 0x2, 0x0, 0x0, 0xB0 };//детская
DeviceAddress addr_T4 = { 0x28, 0x72, 0x26, 0x7B, 0x4, 0x0, 0x0, 0x2E };//гараж
DeviceAddress addr_T5 = { 0x28, 0xCA, 0x1A, 0x3B, 0x4, 0x0, 0x0, 0xCD };//ванная
DeviceAddress addr_T6 = { 0x28, 0xE6, 0xD5, 0xD7, 0x2, 0x0, 0x0, 0xC1 };//улица
DeviceAddress addr_T7 = { 0x28, 0x16, 0xB4, 0x7A, 0x4, 0x0, 0x0, 0x8A };//спальня2
DeviceAddress addr_T8 = { 0x28, 0x2B, 0x86, 0xD7, 0x2, 0x0, 0x0, 0xCF };//зал
DeviceAddress addr_T9 = { 0x28, 0xAB, 0x9D, 0xD7, 0x2, 0x0, 0x0, 0x29 };//мансарда
! float T1=0;
float T2=0;
float T3=0;
float T4=0;
float T5=0;
float T6=0;
float T7=0;
float T8=0;
float T9=0;
! //dht DHT;
//#define DHT22_PIN 9
//float Hout = 0;
//float Tout = 0;
! ////////////////////////////////////////////////////////////////////////////
//void callback(char* topic, byte* payload, unsigned int length) {
// payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
// String strTopic = String(topic);
// String strPayload = String((char*)payload);
// Serial.println(strPayload);
// callback_iobroker(strTopic, strPayload);
//}
////////////////////////////////////////////////////////////////////////////
void setup() {
Serial.begin(57600);
Serial.println("start");

Serial.print("Locating devices...");
DS_sensors.begin();
Serial.print("Found ");
Serial.print(DS_sensors.getDeviceCount(), DEC);
Serial.println(" devices.");

! // report parasite power requirements
Serial.print("Parasite power is: ");
if (DS_sensors.isParasitePowerMode()) Serial.println("ON");
else Serial.println("OFF");

//Объявляем порты Digital inputs/outputs

for(int i=0 ;i<=n_DI_pin; i++) { pinMode (start_DI_pin [i], INPUT); }
digitalWrite(5, HIGH); //Насос скважины
digitalWrite(4, HIGH); //Электрика
for(int i=0 ;i<=n_DO_pin; i++) { pinMode (start_DO_pin [i], OUTPUT); }

! Ethernet.begin(mac, ip);
if (client.connect(id_connect)) {
getSensors();
control();
//client.publish("myhome/Kitchen/Change_Counter", "0");
//client.publish("myhome/Kitchen/Temp_room", "0");
//client.publish("myhome/Kitchen/Humidity_room", "0");
client.publish("myhome/Temp/Kladovka", "0");
client.publish("myhome/Temp/Kitchen", "0");
client.publish("myhome/Temp/Detskaya", "0");
client.publish("myhome/Temp/Garage", "0");
client.publish("myhome/Temp/Street", "0");
client.publish("myhome/Temp/Spalnya2", "0");
client.publish("myhome/Temp/Zal", "0");
client.publish("myhome/Temp/Mansarda", "0");
client.publish("myhome/Temp/Vannaya", "0");

//client.publish("myhome/Kitchen/Lux", "0");
//client.publish("myhome/Kitchen/Servo", "0");
client.publish("myhome/Temp/MQ7", "0");

client.publish("myhome/Status/Power", "0");
client.publish("myhome/Status/Pompe", "0");

client.subscribe("myhome/Temp/#");
client.subscribe("myhome/Status/#");

}
}
/////////////////////////////////////////////////////////////////////////
void loop() {
client.loop();
control();
getSensors();
if (!client.connected()) {
if (client.connect(id_connect)) {
control();
getSensors();
client.subscribe("myhome/Temp/#");
}
}
}</dallastemperature.h></onewire.h></dht.h></servo.h></pubsubclient.h></ethernet.h></spi.h>`

! и все пингуется, а вот заливаю счетчик - и фиг-вам.... пинг не проходит....[/i][/i]

smoker_vvo

В свое время натыкался на проблемы с СД картами и W5100

instalator

~~@smoker_vvo:~~

А не может быть связанным как то с удаленным конфигом сетевого адреса??

const char* topic_ip = "myhome/elcounter/config/ip";

Заливал этот код в Дуню - все работает…

! ```
`#include <spi.h> // Ethernet shield
#include <ethernet.h> // Ethernet shield
#include <pubsubclient.h> // MQTT
#include <servo.h>
#include <dht.h>
#include <onewire.h>
#include <dallastemperature.h>
Servo servo;
! byte mac[] = { 0xC1, 0x7C, 0x38, 0x41, 0x89, 0x35 };
byte server[] = { 192, 168, 0, 11 }; //IP Брокера
byte ip[] = { 192, 168, 0, 89 }; //IP Клиента (Arduino)
! ////////////////////////////////////////////////////////////////////////////
void callback(char* topic, byte* payload, unsigned int length) {
payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
String strTopic = String(topic);
String strPayload = String((char*)payload);
// Serial.println(strPayload);
callback_iobroker(strTopic, strPayload);
}
! EthernetClient ethClient;
PubSubClient client(server, 1883, callback, ethClient);
#define id_connect "myhome-temp"
#define id_connect "myhome-status"
#define Prefix_subscribe "myhome/Temp/"
#define Prefix_subscribe "myhome/Status/"
! ///////////////Объявляем порты ввода-вывода
#define ServoPin 3 //Порт к которому подключен сервопривод
! const int start_DI_pin []= {2, 4, 5}; // Порты Ввода
int n_DI_pin = sizeof(start_DI_pin) / sizeof(start_DI_pin[0])-1; //Вычисляем длинну массива
! const int start_DO_pin []= {6, 7}; //Порты Вывода
int n_DO_pin = sizeof(start_DO_pin) / sizeof(start_DO_pin[0])-1; //Вычисляем длинну массива
! int DI[] = {0, 0, 0};
int old_DI[] = {0, 0, 0};
! ///////////////////////////Переменные для работы с освещением//////////////////////////////////////
int ServoAngle = 100; //Угол сервопривода при включении
int flag = 0;
int flag2 = 0;
int pause = 0;
! //------------------------------------------- Sensors -------------------------------------------//
const int MQ7_Pin = A0; // Куда подключили MQ7
//int MQ7Value = 0;
int MQ7Value = analogRead(MQ7_Pin);

const int foto_Pin = A1; // устанавливаем входную ногу для Фоторезистора
//unsigned int fotoValue = 0; // цифровое значение фоторезистора
unsigned int fotoValue = analogRead(foto_Pin);

! #define ONE_WIRE_BUS 8
//#define TEMPERATURE_PRECISION 9
OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature DS_sensors(&oneWire);
// 28 80 E9 3A 04 00 00 10
//T0:28 88 AD D7 02 00 00 42
//T1:28 14 A5 D7 02 00 00 B0
//T2:28 72 26 7B 04 00 00 2E
//T3:28 CA 1A 3B 04 00 00 CD
//T4:28 E6 D5 D7 02 00 00 C1
//T5:28 16 B4 7A 04 00 00 8A
//T6:28 2B 86 D7 02 00 00 CF
//T7:28 AB 9D D7 02 00 00 29
DeviceAddress addr_T1 = { 0x28, 0x80, 0xE9, 0x3A, 0x4, 0x0, 0x0, 0x10 };//кладовка
DeviceAddress addr_T2 = { 0x28, 0x88, 0xAD, 0xD7, 0x2, 0x0, 0x0, 0x42 };//кухня
DeviceAddress addr_T3 = { 0x28, 0x14, 0xA5, 0xD7, 0x2, 0x0, 0x0, 0xB0 };//детская
DeviceAddress addr_T4 = { 0x28, 0x72, 0x26, 0x7B, 0x4, 0x0, 0x0, 0x2E };//гараж
DeviceAddress addr_T5 = { 0x28, 0xCA, 0x1A, 0x3B, 0x4, 0x0, 0x0, 0xCD };//ванная
DeviceAddress addr_T6 = { 0x28, 0xE6, 0xD5, 0xD7, 0x2, 0x0, 0x0, 0xC1 };//улица
DeviceAddress addr_T7 = { 0x28, 0x16, 0xB4, 0x7A, 0x4, 0x0, 0x0, 0x8A };//спальня2
DeviceAddress addr_T8 = { 0x28, 0x2B, 0x86, 0xD7, 0x2, 0x0, 0x0, 0xCF };//зал
DeviceAddress addr_T9 = { 0x28, 0xAB, 0x9D, 0xD7, 0x2, 0x0, 0x0, 0x29 };//мансарда
! float T1=0;
float T2=0;
float T3=0;
float T4=0;
float T5=0;
float T6=0;
float T7=0;
float T8=0;
float T9=0;
! //dht DHT;
//#define DHT22_PIN 9
//float Hout = 0;
//float Tout = 0;
! ////////////////////////////////////////////////////////////////////////////
//void callback(char* topic, byte* payload, unsigned int length) {
// payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
// String strTopic = String(topic);
// String strPayload = String((char*)payload);
// Serial.println(strPayload);
// callback_iobroker(strTopic, strPayload);
//}
////////////////////////////////////////////////////////////////////////////
void setup() {
Serial.begin(57600);
Serial.println("start");

Serial.print("Locating devices...");
DS_sensors.begin();
Serial.print("Found ");
Serial.print(DS_sensors.getDeviceCount(), DEC);
Serial.println(" devices.");

! // report parasite power requirements
Serial.print("Parasite power is: ");
if (DS_sensors.isParasitePowerMode()) Serial.println("ON");
else Serial.println("OFF");
//Объявляем порты Digital inputs/outputs
for(int i=0 ;i<=n_DI_pin; i++) { pinMode (start_DI_pin [i], INPUT); }
digitalWrite(5, HIGH); //Насос скважины
digitalWrite(4, HIGH); //Электрика
for(int i=0 ;i<=n_DO_pin; i++) { pinMode (start_DO_pin [i], OUTPUT); }

! Ethernet.begin(mac, ip);
if (client.connect(id_connect)) {
getSensors();
control();
//client.publish("myhome/Kitchen/Change_Counter", "0");
//client.publish("myhome/Kitchen/Temp_room", "0");
//client.publish("myhome/Kitchen/Humidity_room", "0");
client.publish("myhome/Temp/Kladovka", "0");
client.publish("myhome/Temp/Kitchen", "0");
client.publish("myhome/Temp/Detskaya", "0");
client.publish("myhome/Temp/Garage", "0");
client.publish("myhome/Temp/Street", "0");
client.publish("myhome/Temp/Spalnya2", "0");
client.publish("myhome/Temp/Zal", "0");
client.publish("myhome/Temp/Mansarda", "0");
client.publish("myhome/Temp/Vannaya", "0");
//client.publish("myhome/Kitchen/Lux", "0");
//client.publish("myhome/Kitchen/Servo", "0");
client.publish("myhome/Temp/MQ7", "0");

client.publish("myhome/Status/Power", "0");
client.publish("myhome/Status/Pompe", "0");

client.subscribe("myhome/Temp/#");
client.subscribe("myhome/Status/#");
}
}
/////////////////////////////////////////////////////////////////////////
void loop() {
client.loop();
control();
getSensors();
if (!client.connected()) {
if (client.connect(id_connect)) {
control();
getSensors();
client.subscribe("myhome/Temp/#");
}
}
}</dallastemperature.h></onewire.h></dht.h></servo.h></pubsubclient.h></ethernet.h></spi.h>`

! и все пингуется, а вот заливаю счетчик - и фиг-вам.... пинг не проходит....нет, вечером будет время проверю твой код[/i][/i]
``` `

smoker_vvo

ок.

а я еще с твоим по колдую…..

instalator

~~@smoker_vvo:~~

ок.

а я еще с твоим по колдую….. `

! ```
`#include <spi.h>
#include <ethernet.h>
#include <pubsubclient.h>
#include <eeprom.h>
//#include <avr wdt.h="">
! #define PWR_CTRL A2 //Контроль напряжения
#define LED 9 //Светодиод
#define CHK_ADR 100
#define CNT_ADR 10
#define PWR_ADR 20
#define POLL_ADR 30
#define RATIO_ADR 40
! const char* topic_err = "myhome/test/error";
const char* topic_cnt = "myhome/test/count";
const char* topic_pwr = "myhome/test/power";
const char* topic_amp = "myhome/test/amp";
const char* topic_save = "myhome/test/save";
const char* topic_correction = "myhome/test/correction";
const char* topic_connection = "myhome/test/connection";
const char* topic_ip = "myhome/test/config/ip";
const char* topic_polling = "myhome/test/config/polling";
const char* topic_bounce = "myhome/test/config/bounce";
const char* topic_num = "myhome/test/config/num";
const char* topic_reset = "myhome/test/config/reset";
const char* topic_raw = "myhome/test/RAW";
const char* subscr = "myhome/test/#";
! byte mac[] = { 0xDE, 0xA3, 0xBE, 0xE4, 0xDE, 0x35 };
byte ip[] = { 192, 168, 1, 59};
byte server[] = { 192, 168, 1, 190};
! unsigned long cnt = 0;
unsigned long prev_cnt = 2;
unsigned long pwr = 0;
unsigned long prev_pwr = 2;
int amp = 0;
int prev_amp = 2;
int num = 0;
int prev_num;
int bounce = 10;
int prev_bounce;
int chk = 0;
int chk_S = 0;
unsigned long prevMillis = 0;
unsigned long prevMillis_cnt = 0;
int poll = 5000;
bool error = 0;
String cmd = "";
bool strComplete = false;
char buf [50];
char buffer[100];
char s[16];
! ////////////////////////////////////////////////////////////////////////////
void callback(char* topic, byte* payload, unsigned int length) {
payload[length] = '\0';
String strTopic = String(topic);
String strPayload = String((char*)payload);
callback_iobroker(strTopic, strPayload);
}
! EthernetClient ethClient;
PubSubClient client(ethClient);
! void setup() {
Serial.begin(57600);
//MCUSR = 0;
// wdt_disable();
Serial.println("WDT_disable");
cmd.reserve(100);
delay(10000);

Serial.println("Starting......");

! if (EEPROM.read(1) != 99) { //Если первый запуск
EEPROM.write(1, 99);
for (int i = 0 ; i < 4; i++) {
EEPROM.write(110 + i, ip[i]);
}
for (int i = 0 ; i < 4; i++) {
EEPROM.write(120 + i, server[i]);
}
} else {
chk = EEPROMReadInt(CHK_ADR);
cnt = EEPROMReadLong(CNT_ADR);
poll = EEPROMReadInt(POLL_ADR);
chk_S = poll - 500;
if (chk != chk_S) {
error = 2;
}
for (int i = 0; i < 4; i++) {
ip[i] = EEPROM.read(110 + i);
}
for (int i = 0; i < 4; i++) {
server[i] = EEPROM.read(120 + i);
}
}
! pinMode(LED, OUTPUT);
! client.setServer(server, 1883);
client.setCallback(callback);
Ethernet.begin(mac, ip);

delay(200);
//wdt_enable(WDTO_8S);
Serial.println("WDTO_8S");
if (client.connect("test")){
digitalWrite(LED, LOW);
Public();
}
}

! void serialEvent() {
while (Serial.available() > 0) {
char inChar = (char)Serial.read();
cmd += inChar;
if (inChar == '\n') {
strComplete = true;
}
}
}
! void loop() {
// wdt_reset();
Serial.println("WDT_reset");
client.loop();
if (!client.connected()) {
reconnect();
}
! /if (analogRead(PWR_CTRL) < 1000) {
digitalWrite(LED, LOW);
save();
delay(10000);
}/
! if (strComplete) {
digitalWrite(LED, !digitalRead(LED));
cmd.toCharArray(buffer, 100);
cnt = atoi(strtok(buffer, ";"));
pwr = atoi(strtok(NULL, ";"));
amp = atoi(strtok(NULL, ";"));
bounce = atoi(strtok(NULL, ";"));
num = atoi(strtok(NULL, ";"));
error = atoi(strtok(NULL, ";"));
client.publish(topic_raw, StrToChar(cmd));
cmd = "";
strComplete = false;
}
! if (millis() - prevMillis >= poll) {
// wdt_reset();
Serial.println("WDT_reset-");
prevMillis = millis();
if (cnt != prev_cnt || pwr != prev_pwr || amp != prev_amp) {
prev_cnt = cnt;
prev_pwr = pwr;
prev_amp = amp;
client.publish(topic_cnt, IntToChar(cnt));
client.publish(topic_pwr, IntToChar(pwr));
client.publish(topic_amp, IntToChar(amp));
}
if (num != prev_num || bounce != prev_bounce) {
prev_num = num;
prev_bounce = bounce;
client.publish(topic_num, IntToChar(num));
client.publish(topic_bounce, IntToChar(bounce));
}
if (error > 0) {
client.publish(topic_err, "err");
} else {
client.publish(topic_err, " ");
}
}
}
! void callback_iobroker(String strTopic, String strPayload) {
if (strTopic == topic_correction) {
cnt = atol((strPayload).c_str());
Serial.print("SC");
Serial.println(cnt);
client.publish(topic_correction, "0");
}
else if (strTopic == topic_save) {
if (strPayload == "true") {
Serial.println("SS");
save();
client.publish(topic_save, "false");
}
}
else if (strTopic == topic_polling) {
poll = strPayload.toInt();
if (poll < 1000) {
poll = 1000;
} else if (poll > 32767) {
poll = 32767;
}
EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации
client.publish(topic_polling, IntToChar(poll));
}
else if (strTopic == topic_reset) {
if (strPayload == "true") {
client.publish(topic_reset, "false");
// reboot();
Serial.println("Reboot");
}
}
else if (strTopic == topic_bounce) {
bounce = strPayload.toInt();
if (bounce < 0) {
bounce = 0;
} else if (bounce > 10000) {
bounce = 10000;
}
Serial.print("SB");
Serial.println(bounce);
client.publish(topic_bounce, IntToChar(bounce));
}
else if (strTopic == topic_num) {
num = strPayload.toInt();
if (num < 0) {
num = 0;
} else if (num > 32767) {
num = 32767;
}
Serial.print("SN");
Serial.println(num);
client.publish(topic_num, IntToChar(num));
}
}
! void save() {
chk = poll - 500;
EEPROMWriteLong(CNT_ADR, cnt); //Пишем показания счетчика в eeprom из переменной
EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации
EEPROMWriteInt(CHK_ADR, chk); //чек
}
! void reboot() {
//save();
//delay(500);
// wdt_enable(WDTO_1S);
Serial.println("void reboot");
//for (;;) {}
}
! char* StrToChar (String str) {
int length = str.length();
str.toCharArray(buf, length + 1);
return buf;
}
! void EEPROMWriteLong(int p_address, unsigned long p_value) {
byte four = (p_value & 0xFF);
byte three = ((p_value >> & 0xFF);
byte two = ((p_value >> 16) & 0xFF);
byte one = ((p_value >> 24) & 0xFF);
EEPROM.write(p_address, four);
EEPROM.write(p_address + 1, three);
EEPROM.write(p_address + 2, two);
EEPROM.write(p_address + 3, one);
}
! unsigned long EEPROMReadLong(int p_address) {
long four = EEPROM.read(p_address);
long three = EEPROM.read(p_address + 1);
long two = EEPROM.read(p_address + 2);
long one = EEPROM.read(p_address + 3);
return ((four << 0) & 0xFF) + ((three << & 0xFFFF) + ((two << 16) & 0xFFFFFF) + ((one << 24) & 0xFFFFFFFF);
}
! void EEPROMWriteInt(int p_address, int p_value) {
byte lowByte = ((p_value >> 0) & 0xFF);
byte highByte = ((p_value >> & 0xFF);
EEPROM.write(p_address, lowByte);
EEPROM.write(p_address + 1, highByte);
}
unsigned int EEPROMReadInt(int p_address) {
byte lowByte = EEPROM.read(p_address);
byte highByte = EEPROM.read(p_address + 1);
return ((lowByte << 0) & 0xFF) + ((highByte << & 0xFF00);
}
! char* IntToChar (unsigned long a) {
sprintf(buf, "%lu", a);
return buf;
}
! void Public() {
sprintf(s, "%d.%d.%d.%d", ip[0], ip[1], ip[2], ip[3]);
client.publish(topic_err, " ");
client.publish(topic_cnt, IntToChar(cnt));
client.publish(topic_pwr, IntToChar(pwr));
client.publish(topic_amp, IntToChar(amp));
client.publish(topic_save, "false");
client.publish(topic_correction, "0");
client.publish(topic_connection, "true");
client.publish(topic_ip, s);
client.publish(topic_polling, IntToChar(poll));
client.publish(topic_bounce, IntToChar(bounce));
client.publish(topic_num, IntToChar(num));
client.publish(topic_reset, "false");
client.subscribe(subscr);
}
void reconnect() {
int a = 0;
while (!client.connected()) {
a++;
digitalWrite(LED, !digitalRead(LED));
//wdt_reset();
Serial.println("WDT reset");
if (client.connect("test")) {
digitalWrite(LED, LOW);
Public();
} else {
delay(10000);
}
if (a >= 10) {
// wdt_enable(WDTO_1S);
Serial.println("WDTO_1S");
}
}
}</avr></eeprom.h></pubsubclient.h></ethernet.h></spi.h>`
Работает[/i][/i][/i][/i]

smoker_vvo

Убейте меня!!! ОН НЕ РАБОТАЕТ….. Ну не пингуется этот ip, я поменял на свои......

instalator

~~@smoker_vvo:~~

Убейте меня!!! ОН НЕ РАБОТАЕТ….. Ну не пингуется этот ip, я поменял на свои...... `
библиотеки последних версии?

smoker_vvo

Начнем с простого…. Какая IDE

smoker_vvo

в IDE 1.5.2 гружу вот этот скетч:

! ````
/*
Web Server

A simple web server that shows the value of the analog input pins.
using an Arduino Wiznet Ethernet shield.

Circuit:

Ethernet shield attached to pins 10, 11, 12, 13
Analog inputs attached to pins A0 through A5 (optional)

created 18 Dec 2009
by David A. Mellis
modified 9 Apr 2012
by Tom Igoe

*/

! #include <spi.h>#include <ethernet.h>// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
IPAddress ip(192,168,0, 89);
! // Initialize the Ethernet server library
// with the IP address and port you want to use
// (port 80 is default for HTTP):
EthernetServer server(80);
! void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for Leonardo only
}
! // start the Ethernet connection and the server:
Ethernet.begin(mac, ip);
server.begin();
Serial.print("server is at ");
Serial.println(Ethernet.localIP());
}
! void loop() {
// listen for incoming clients
EthernetClient client = server.available();
if (client) {
Serial.println("new client");
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected()) {
if (client.available()) {
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank) {
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connection: close");
client.println();
client.println("");
client.println("");
// add a meta refresh tag, so the browser pulls again every 5 seconds:
client.println("");
// output the value of each analog input pin
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
int sensorReading = analogRead(analogChannel);
client.print("analog input ");
client.print(analogChannel);
client.print(" is ");
client.print(sensorReading);
client.println("
");
}
client.println("");
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r') {
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
Serial.println("client disonnected");
}
}</ethernet.h></spi.h>


Пинг - отличный, и веб пускает,

smoker_vvo

в 1ю8ю2 - тоже проблем нет…...

smoker_vvo

1ю6ю13 - полет нормальный

и 1.0.6 - работает…...

smoker_vvo

IDE 1.6.13 этот скетч - работает, все пингуется и данные идут

! ```
`#include <spi.h> // Ethernet shield
#include <ethernet.h> // Ethernet shield
#include <pubsubclient.h> // MQTT
#include <servo.h>
#include <dht.h>
#include <onewire.h>
#include <dallastemperature.h>
Servo servo;
! byte mac[] = { 0xC1, 0x7C, 0x38, 0x41, 0x89, 0x35 };
byte server[] = { 192, 168, 0, 11 }; //IP Брокера
byte ip[] = { 192, 168, 0, 89 }; //IP Клиента (Arduino)
! ////////////////////////////////////////////////////////////////////////////
void callback(char* topic, byte* payload, unsigned int length) {
payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
String strTopic = String(topic);
String strPayload = String((char*)payload);
// Serial.println(strPayload);
callback_iobroker(strTopic, strPayload);
}
! EthernetClient ethClient;
PubSubClient client(server, 1883, callback, ethClient);
#define id_connect "myhome-temp"
#define id_connect "myhome-status"
#define Prefix_subscribe "myhome/Temp/"
#define Prefix_subscribe "myhome/Status/"
! ///////////////Объявляем порты ввода-вывода
#define ServoPin 3 //Порт к которому подключен сервопривод
! const int start_DI_pin []= {2, 4, 5}; // Порты Ввода
int n_DI_pin = sizeof(start_DI_pin) / sizeof(start_DI_pin[0])-1; //Вычисляем длинну массива
! const int start_DO_pin []= {6, 7}; //Порты Вывода
int n_DO_pin = sizeof(start_DO_pin) / sizeof(start_DO_pin[0])-1; //Вычисляем длинну массива
! int DI[] = {0, 0, 0};
int old_DI[] = {0, 0, 0};
! ///////////////////////////Переменные для работы с освещением//////////////////////////////////////
int ServoAngle = 100; //Угол сервопривода при включении
int flag = 0;
int flag2 = 0;
int pause = 0;
! //------------------------------------------- Sensors -------------------------------------------//
const int MQ7_Pin = A0; // Куда подключили MQ7
//int MQ7Value = 0;
int MQ7Value = analogRead(MQ7_Pin);

const int foto_Pin = A1; // устанавливаем входную ногу для Фоторезистора
//unsigned int fotoValue = 0; // цифровое значение фоторезистора
unsigned int fotoValue = analogRead(foto_Pin);

! #define ONE_WIRE_BUS 8
//#define TEMPERATURE_PRECISION 9
OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature DS_sensors(&oneWire);
// 28 80 E9 3A 04 00 00 10
//T0:28 88 AD D7 02 00 00 42
//T1:28 14 A5 D7 02 00 00 B0
//T2:28 72 26 7B 04 00 00 2E
//T3:28 CA 1A 3B 04 00 00 CD
//T4:28 E6 D5 D7 02 00 00 C1
//T5:28 16 B4 7A 04 00 00 8A
//T6:28 2B 86 D7 02 00 00 CF
//T7:28 AB 9D D7 02 00 00 29
DeviceAddress addr_T1 = { 0x28, 0x80, 0xE9, 0x3A, 0x4, 0x0, 0x0, 0x10 };//кладовка
DeviceAddress addr_T2 = { 0x28, 0x88, 0xAD, 0xD7, 0x2, 0x0, 0x0, 0x42 };//кухня
DeviceAddress addr_T3 = { 0x28, 0x14, 0xA5, 0xD7, 0x2, 0x0, 0x0, 0xB0 };//детская
DeviceAddress addr_T4 = { 0x28, 0x72, 0x26, 0x7B, 0x4, 0x0, 0x0, 0x2E };//гараж
DeviceAddress addr_T5 = { 0x28, 0xCA, 0x1A, 0x3B, 0x4, 0x0, 0x0, 0xCD };//ванная
DeviceAddress addr_T6 = { 0x28, 0xE6, 0xD5, 0xD7, 0x2, 0x0, 0x0, 0xC1 };//улица
DeviceAddress addr_T7 = { 0x28, 0x16, 0xB4, 0x7A, 0x4, 0x0, 0x0, 0x8A };//спальня2
DeviceAddress addr_T8 = { 0x28, 0x2B, 0x86, 0xD7, 0x2, 0x0, 0x0, 0xCF };//зал
DeviceAddress addr_T9 = { 0x28, 0xAB, 0x9D, 0xD7, 0x2, 0x0, 0x0, 0x29 };//мансарда
! float T1=0;
float T2=0;
float T3=0;
float T4=0;
float T5=0;
float T6=0;
float T7=0;
float T8=0;
float T9=0;
! //dht DHT;
//#define DHT22_PIN 9
//float Hout = 0;
//float Tout = 0;
! ////////////////////////////////////////////////////////////////////////////
//void callback(char* topic, byte* payload, unsigned int length) {
// payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
// String strTopic = String(topic);
// String strPayload = String((char*)payload);
// Serial.println(strPayload);
// callback_iobroker(strTopic, strPayload);
//}
////////////////////////////////////////////////////////////////////////////
void setup() {
Serial.begin(57600);
Serial.println("start");

Serial.print("Locating devices...");
DS_sensors.begin();
Serial.print("Found ");
Serial.print(DS_sensors.getDeviceCount(), DEC);
Serial.println(" devices.");

! // report parasite power requirements
Serial.print("Parasite power is: ");
if (DS_sensors.isParasitePowerMode()) Serial.println("ON");
else Serial.println("OFF");

//Объявляем порты Digital inputs/outputs

for(int i=0 ;i<=n_DI_pin; i++) { pinMode (start_DI_pin [i], INPUT); }
digitalWrite(5, HIGH); //Насос скважины
digitalWrite(4, HIGH); //Электрика
for(int i=0 ;i<=n_DO_pin; i++) { pinMode (start_DO_pin [i], OUTPUT); }

! Ethernet.begin(mac, ip);
if (client.connect(id_connect)) {
getSensors();
control();
//client.publish("myhome/Kitchen/Change_Counter", "0");
//client.publish("myhome/Kitchen/Temp_room", "0");
//client.publish("myhome/Kitchen/Humidity_room", "0");
client.publish("myhome/Temp/Kladovka", "0");
client.publish("myhome/Temp/Kitchen", "0");
client.publish("myhome/Temp/Detskaya", "0");
client.publish("myhome/Temp/Garage", "0");
client.publish("myhome/Temp/Street", "0");
client.publish("myhome/Temp/Spalnya2", "0");
client.publish("myhome/Temp/Zal", "0");
client.publish("myhome/Temp/Mansarda", "0");
client.publish("myhome/Temp/Vannaya", "0");

//client.publish("myhome/Kitchen/Lux", "0");
//client.publish("myhome/Kitchen/Servo", "0");
client.publish("myhome/Temp/MQ7", "0");

client.publish("myhome/Status/Power", "0");
client.publish("myhome/Status/Pompe", "0");

client.subscribe("myhome/Temp/#");
client.subscribe("myhome/Status/#");

}
}
/////////////////////////////////////////////////////////////////////////
void loop() {
client.loop();
control();
getSensors();
if (!client.connected()) {
if (client.connect(id_connect)) {
control();
getSensors();
client.subscribe("myhome/Temp/#");
}
}
}</dallastemperature.h></onewire.h></dht.h></servo.h></pubsubclient.h></ethernet.h></spi.h>`

! А заливаем этот - и ни чего....
! >! ~~[spoiler]~~`~~[code]~~#include <spi.h>
#include <ethernet.h>
#include <pubsubclient.h>
#include <eeprom.h>
//#include <avr wdt.h="">
! #define PWR_CTRL A2 //Контроль напряжения
#define LED 9 //Светодиод
#define CHK_ADR 100
#define CNT_ADR 10
#define PWR_ADR 20
#define POLL_ADR 30
#define RATIO_ADR 40
! const char* topic_err = "myhome/test/error";
const char* topic_cnt = "myhome/test/count";
const char* topic_pwr = "myhome/test/power";
const char* topic_amp = "myhome/test/amp";
const char* topic_save = "myhome/test/save";
const char* topic_correction = "myhome/test/correction";
const char* topic_connection = "myhome/test/connection";
const char* topic_ip = "myhome/test/config/ip";
const char* topic_polling = "myhome/test/config/polling";
const char* topic_bounce = "myhome/test/config/bounce";
const char* topic_num = "myhome/test/config/num";
const char* topic_reset = "myhome/test/config/reset";
const char* topic_raw = "myhome/test/RAW";
const char* subscr = "myhome/test/#";
! byte mac[] = { 0xDE, 0xA3, 0xBE, 0xE4, 0xDE, 0x35 };
byte ip[] = { 192, 168, 0, 89};
byte server[] = { 192, 168, 0, 15};
! unsigned long cnt = 0;
unsigned long prev_cnt = 2;
unsigned long pwr = 0;
unsigned long prev_pwr = 2;
int amp = 0;
int prev_amp = 2;
int num = 0;
int prev_num;
int bounce = 10;
int prev_bounce;
int chk = 0;
int chk_S = 0;
unsigned long prevMillis = 0;
unsigned long prevMillis_cnt = 0;
int poll = 5000;
bool error = 0;
String cmd = "";
bool strComplete = false;
char buf [50];
char buffer[100];
char s[16];
! ////////////////////////////////////////////////////////////////////////////
void callback(char* topic, byte* payload, unsigned int length) {
payload[length] = '\0';
String strTopic = String(topic);
String strPayload = String((char*)payload);
callback_iobroker(strTopic, strPayload);
}
! EthernetClient ethClient;
PubSubClient client(ethClient);
! void setup() {
Serial.begin(57600);
//MCUSR = 0;
// wdt_disable();
Serial.println("WDT_disable");
cmd.reserve(100);
delay(10000);

Serial.println("Starting......");

! if (EEPROM.read(1) != 99) { //Если первый запуск
EEPROM.write(1, 99);
for (int i = 0 ; i < 4; i++) {
EEPROM.write(110 + i, ip[i]);
}
for (int i = 0 ; i < 4; i++) {
EEPROM.write(120 + i, server[i]);
}
} else {
chk = EEPROMReadInt(CHK_ADR);
cnt = EEPROMReadLong(CNT_ADR);
poll = EEPROMReadInt(POLL_ADR);
chk_S = poll - 500;
if (chk != chk_S) {
error = 2;
}
for (int i = 0; i < 4; i++) {
ip[i] = EEPROM.read(110 + i);
}
for (int i = 0; i < 4; i++) {
server[i] = EEPROM.read(120 + i);
}
}
! pinMode(LED, OUTPUT);
! client.setServer(server, 1883);
client.setCallback(callback);
Ethernet.begin(mac, ip);

delay(200);
//wdt_enable(WDTO_8S);
Serial.println("WDTO_8S");
if (client.connect("test")){
digitalWrite(LED, LOW);
Public();
}
}

! void serialEvent() {
while (Serial.available() > 0) {
char inChar = (char)Serial.read();
cmd += inChar;
if (inChar == '\n') {
strComplete = true;
}
}
}
! void loop() {
// wdt_reset();
Serial.println("WDT_reset");
client.loop();
if (!client.connected()) {
reconnect();
}
! /if (analogRead(PWR_CTRL) < 1000) {
digitalWrite(LED, LOW);
save();
delay(10000);
}/
! if (strComplete) {
digitalWrite(LED, !digitalRead(LED));
cmd.toCharArray(buffer, 100);
cnt = atoi(strtok(buffer, ";"));
pwr = atoi(strtok(NULL, ";"));
amp = atoi(strtok(NULL, ";"));
bounce = atoi(strtok(NULL, ";"));
num = atoi(strtok(NULL, ";"));
error = atoi(strtok(NULL, ";"));
client.publish(topic_raw, StrToChar(cmd));
cmd = "";
strComplete = false;
}
! if (millis() - prevMillis >= poll) {
// wdt_reset();
Serial.println("WDT_reset-");
prevMillis = millis();
if (cnt != prev_cnt || pwr != prev_pwr || amp != prev_amp) {
prev_cnt = cnt;
prev_pwr = pwr;
prev_amp = amp;
client.publish(topic_cnt, IntToChar(cnt));
client.publish(topic_pwr, IntToChar(pwr));
client.publish(topic_amp, IntToChar(amp));
}
if (num != prev_num || bounce != prev_bounce) {
prev_num = num;
prev_bounce = bounce;
client.publish(topic_num, IntToChar(num));
client.publish(topic_bounce, IntToChar(bounce));
}
if (error > 0) {
client.publish(topic_err, "err");
} else {
client.publish(topic_err, " ");
}
}
}
! void callback_iobroker(String strTopic, String strPayload) {
if (strTopic == topic_correction) {
cnt = atol((strPayload).c_str());
Serial.print("SC");
Serial.println(cnt);
client.publish(topic_correction, "0");
}
else if (strTopic == topic_save) {
if (strPayload == "true") {
Serial.println("SS");
save();
client.publish(topic_save, "false");
}
}
else if (strTopic == topic_polling) {
poll = strPayload.toInt();
if (poll < 1000) {
poll = 1000;
} else if (poll > 32767) {
poll = 32767;
}
EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации
client.publish(topic_polling, IntToChar(poll));
}
else if (strTopic == topic_reset) {
if (strPayload == "true") {
client.publish(topic_reset, "false");
// reboot();
Serial.println("Reboot");
}
}
else if (strTopic == topic_bounce) {
bounce = strPayload.toInt();
if (bounce < 0) {
bounce = 0;
} else if (bounce > 10000) {
bounce = 10000;
}
Serial.print("SB");
Serial.println(bounce);
client.publish(topic_bounce, IntToChar(bounce));
}
else if (strTopic == topic_num) {
num = strPayload.toInt();
if (num < 0) {
num = 0;
} else if (num > 32767) {
num = 32767;
}
Serial.print("SN");
Serial.println(num);
client.publish(topic_num, IntToChar(num));
}
}
! void save() {
chk = poll - 500;
EEPROMWriteLong(CNT_ADR, cnt); //Пишем показания счетчика в eeprom из переменной
EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации
EEPROMWriteInt(CHK_ADR, chk); //чек
}
! void reboot() {
//save();
//delay(500);
// wdt_enable(WDTO_1S);
Serial.println("void reboot");
//for (;;) {}
}
! char* StrToChar (String str) {
int length = str.length();
str.toCharArray(buf, length + 1);
return buf;
}
! void EEPROMWriteLong(int p_address, unsigned long p_value) {
byte four = (p_value & 0xFF);
byte three = ((p_value >> & 0xFF);
byte two = ((p_value >> 16) & 0xFF);
byte one = ((p_value >> 24) & 0xFF);
EEPROM.write(p_address, four);
EEPROM.write(p_address + 1, three);
EEPROM.write(p_address + 2, two);
EEPROM.write(p_address + 3, one);
}
! unsigned long EEPROMReadLong(int p_address) {
long four = EEPROM.read(p_address);
long three = EEPROM.read(p_address + 1);
long two = EEPROM.read(p_address + 2);
long one = EEPROM.read(p_address + 3);
return ((four << 0) & 0xFF) + ((three << & 0xFFFF) + ((two << 16) & 0xFFFFFF) + ((one << 24) & 0xFFFFFFFF);
}
! void EEPROMWriteInt(int p_address, int p_value) {
byte lowByte = ((p_value >> 0) & 0xFF);
byte highByte = ((p_value >> & 0xFF);
EEPROM.write(p_address, lowByte);
EEPROM.write(p_address + 1, highByte);
}
unsigned int EEPROMReadInt(int p_address) {
byte lowByte = EEPROM.read(p_address);
byte highByte = EEPROM.read(p_address + 1);
return ((lowByte << 0) & 0xFF) + ((highByte << & 0xFF00);
}
! char* IntToChar (unsigned long a) {
sprintf(buf, "%lu", a);
return buf;
}
! void Public() {
sprintf(s, "%d.%d.%d.%d", ip[0], ip[1], ip[2], ip[3]);
client.publish(topic_err, " ");
client.publish(topic_cnt, IntToChar(cnt));
client.publish(topic_pwr, IntToChar(pwr));
client.publish(topic_amp, IntToChar(amp));
client.publish(topic_save, "false");
client.publish(topic_correction, "0");
client.publish(topic_connection, "true");
client.publish(topic_ip, s);
client.publish(topic_polling, IntToChar(poll));
client.publish(topic_bounce, IntToChar(bounce));
client.publish(topic_num, IntToChar(num));
client.publish(topic_reset, "false");
client.subscribe(subscr);
}
void reconnect() {
int a = 0;
while (!client.connected()) {
a++;
digitalWrite(LED, !digitalRead(LED));
//wdt_reset();
Serial.println("WDT reset");
if (client.connect("test")) {
digitalWrite(LED, LOW);
Public();
} else {
delay(10000);
}
if (a >= 10) {
// wdt_enable(WDTO_1S);
Serial.println("WDTO_1S");
}
}
}</avr></eeprom.h></pubsubclient.h></ethernet.h></spi.h>`
! Ни пинга, ни данных....[/i][/i][/i][/i][/code][/spoiler][/i][/i]

instalator

~~@smoker_vvo:~~

Начнем с простого…. Какая IDE `
ide 1.8.3

Ethernet 1.1.2

PubSubCliet 2.6.0

smoker_vvo

IDE 1.8.4, остальное совпадает…...

Хорошо, с программным уровнем разобрались. Теперь аппаратный.... Arduino MEGA 2560+EthernetShield W5100

NEWS

Скрипт для счётчика

Support us

901
Online

31.7k
Users

79.7k
Topics

1.3m
Posts

NEWS

Скрипт для счётчика

Support us

901Online

31.7kUsers

79.7kTopics

1.3mPosts

901
Online

31.7k
Users

79.7k
Topics

1.3m
Posts