Скрипт для счётчика

smoker_vvo

для контроля питания, что то подавать надо, или это аппаратно решено??

smoker_vvo

Сразу скажу, не селен я в программировании, все что делаю сам для ардуины - это просто результат ДООЛГОГО разбирательства чужих кодов, делаю на уровне подсознания…..

instalator

~~@smoker_vvo:~~

Вачдог…

Это

void reboot() {
  save();
  delay(500);
  wdt_enable(WDTO_1S);
  for (;;) {}
}
```` `

Тут тоже. В начале кода еще ищи команду wdt_enable.

Либо прошей загрузчик https://github.com/instalator/optiboot, в котором исправлен баг с ватчдогом.

smoker_vvo

А вот тут и возникла проблема… Не заливаются скетчи.... любая попытка заканчивается ошибкой закачки скетча.... И бешеный светодиод......

instalator

~~@smoker_vvo:~~

А вот тут и возникла проблема… Не заливаются скетчи.... любая попытка заканчивается ошибкой закачки скетча.... И бешеный светодиод...... `
Прошей загрузчик оптибут или шей ее через программатор

smoker_vvo

Ну тогда давай рекомендации что и как делать, через что прошивать, у меня голова опухла от обилия информации о прошивке оптибута

instalator

~~@smoker_vvo:~~

Ну тогда давай рекомендации что и как делать, через что прошивать, у меня голова опухла от обилия информации о прошивке оптибута `

http://blog.instalator.ru/archives/798

smoker_vvo

Доброго времени…

Появилось время заниматься проектом дальше. и вот какие проблемы, если с WDT я поступил грубо, просто закоментил его, то с ethernetom вообще ни чего не могу понять. Учитывая что у тебя была другая карта, использую библиотеку для своей.... и ничего не работает....

1. ping - ни чего нет

2. соответсвенно в IOBе то же тишина.

заливал другие скетчи - с сетевой проблем нет.

вот код :

! ```
#include <spi.h> #include <ethernet.h> #include <pubsubclient.h> #include <eeprom.h> //#include <avr wdt.h=""> ! #define PWR_CTRL A2 //Контроль напряжения #define LED 9 //Светодиод #define CHK_ADR 100 #define CNT_ADR 10 #define PWR_ADR 20 #define POLL_ADR 30 #define RATIO_ADR 40 ! const char* topic_err = "myhome/elcounter/error"; const char* topic_cnt = "myhome/elcounter/count"; const char* topic_pwr = "myhome/elcounter/power"; const char* topic_amp = "myhome/elcounter/amp"; const char* topic_save = "myhome/elcounter/save"; const char* topic_correction = "myhome/elcounter/correction"; const char* topic_connection = "myhome/elcounter/connection"; const char* topic_ip = "myhome/elcounter/config/ip"; const char* topic_polling = "myhome/elcounter/config/polling"; const char* topic_bounce = "myhome/elcounter/config/bounce"; const char* topic_num = "myhome/elcounter/config/num"; const char* topic_reset = "myhome/elcounter/config/reset"; const char* topic_raw = "myhome/elcounter/RAW"; const char* subscr = "myhome/elcounter/#"; ! byte mac[] = { 0xDE, 0xAD, 0xBE, 0xE4, 0xDE, 0x35 }; byte ip[] = { 192, 168, 0, 89}; byte server[] = { 192, 168, 0, 15}; ! unsigned long cnt = 0; unsigned long prev_cnt = 2; unsigned long pwr = 0; unsigned long prev_pwr = 2; int amp = 0; int prev_amp = 2; int num = 0; int prev_num; int bounce = 10; int prev_bounce; int chk = 0; int chk_S = 0; unsigned long prevMillis = 0; unsigned long prevMillis_cnt = 0; int poll = 5000; bool error = 0; String cmd = ""; bool strComplete = false; char buf [50]; char buffer[100]; char s[16]; ! //////////////////////////////////////////////////////////////////////////// void callback(char* topic, byte* payload, unsigned int length) { payload[length] = '\0'; String strTopic = String(topic); String strPayload = String((char*)payload); callback_iobroker(strTopic, strPayload); } ! EthernetClient ethClient; PubSubClient client(server, 1883, callback, ethClient); ! void setup() { MCUSR = 0; // wdt_disable(); Serial.println("WDT_disable"); cmd.reserve(100); delay(10000); Serial.begin(57600); Serial.println("Starting......"); ! if (EEPROM.read(1) != 99) { //Если первый запуск EEPROM.write(1, 99); for (int i = 0 ; i < 4; i++) { EEPROM.write(110 + i, ip[i]); } for (int i = 0 ; i < 4; i++) { EEPROM.write(120 + i, server[i]); } } else { chk = EEPROMReadInt(CHK_ADR); cnt = EEPROMReadLong(CNT_ADR); poll = EEPROMReadInt(POLL_ADR); chk_S = poll - 500; if (chk != chk_S) { error = 2; } for (int i = 0; i < 4; i++) { ip[i] = EEPROM.read(110 + i); } for (int i = 0; i < 4; i++) { server[i] = EEPROM.read(120 + i); } } ! pinMode(LED, OUTPUT); ! // client.setServer(server, 1883); // client.setCallback(callback); Ethernet.begin(mac, ip); delay(200); //wdt_enable(WDTO_8S); Serial.println("WDTO_8S"); if (client.connect("elcounter")) { digitalWrite(LED, LOW); Public(); } } ! void serialEvent() { while (Serial.available() > 0) { char inChar = (char)Serial.read(); cmd += inChar; if (inChar == '\n') { strComplete = true; } } } ! void callback_iobroker(String strTopic, String strPayload) { if (strTopic == topic_correction) { cnt = atol((strPayload).c_str()); Serial.print("SC"); Serial.println(cnt); client.publish(topic_correction, "0"); } else if (strTopic == topic_save) { if (strPayload == "true") { Serial.println("SS"); save(); client.publish(topic_save, "false"); } } else if (strTopic == topic_polling) { poll = strPayload.toInt(); if (poll < 1000) { poll = 1000; } else if (poll > 32767) { poll = 32767; } EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации client.publish(topic_polling, IntToChar(poll)); } else if (strTopic == topic_reset) { if (strPayload == "true") { client.publish(topic_reset, "false"); // reboot(); Serial.println("Reboot"); } } else if (strTopic == topic_bounce) { bounce = strPayload.toInt(); if (bounce < 0) { bounce = 0; } else if (bounce > 10000) { bounce = 10000; } Serial.print("SB"); Serial.println(bounce); client.publish(topic_bounce, IntToChar(bounce)); } else if (strTopic == topic_num) { num = strPayload.toInt(); if (num < 0) { num = 0; } else if (num > 32767) { num = 32767; } Serial.print("SN"); Serial.println(num); client.publish(topic_num, IntToChar(num)); } } ! void save() { chk = poll - 500; EEPROMWriteLong(CNT_ADR, cnt); //Пишем показания счетчика в eeprom из переменной EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации EEPROMWriteInt(CHK_ADR, chk); //чек } ! void reboot() { save(); delay(500); // wdt_enable(WDTO_1S); Serial.println("void reboot"); for (;;) {} } ! char* StrToChar (String str) { int length = str.length(); str.toCharArray(buf, length + 1); return buf; } ! void EEPROMWriteLong(int p_address, unsigned long p_value) { byte four = (p_value & 0xFF); byte three = ((p_value >> 8) & 0xFF); byte two = ((p_value >> 16) & 0xFF); byte one = ((p_value >> 24) & 0xFF); EEPROM.write(p_address, four); EEPROM.write(p_address + 1, three); EEPROM.write(p_address + 2, two); EEPROM.write(p_address + 3, one); } ! unsigned long EEPROMReadLong(int p_address) { long four = EEPROM.read(p_address); long three = EEPROM.read(p_address + 1); long two = EEPROM.read(p_address + 2); long one = EEPROM.read(p_address + 3); return ((four << 0) & 0xFF) + ((three << 8) & 0xFFFF) + ((two << 16) & 0xFFFFFF) + ((one << 24) & 0xFFFFFFFF); } ! void EEPROMWriteInt(int p_address, int p_value) { byte lowByte = ((p_value >> 0) & 0xFF); byte highByte = ((p_value >> 8) & 0xFF); EEPROM.write(p_address, lowByte); EEPROM.write(p_address + 1, highByte); } unsigned int EEPROMReadInt(int p_address) { byte lowByte = EEPROM.read(p_address); byte highByte = EEPROM.read(p_address + 1); return ((lowByte << 0) & 0xFF) + ((highByte << 8) & 0xFF00); } ! char* IntToChar (unsigned long a) { sprintf(buf, "%lu", a); return buf; } ! void Public() { sprintf(s, "%d.%d.%d.%d", ip[0], ip[1], ip[2], ip[3]); client.publish(topic_err, " "); client.publish(topic_cnt, IntToChar(cnt)); client.publish(topic_pwr, IntToChar(pwr)); client.publish(topic_amp, IntToChar(amp)); client.publish(topic_save, "false"); client.publish(topic_correction, "0"); client.publish(topic_connection, "true"); client.publish(topic_ip, s); client.publish(topic_polling, IntToChar(poll)); client.publish(topic_bounce, IntToChar(bounce)); client.publish(topic_num, IntToChar(num)); client.publish(topic_reset, "false"); client.subscribe(subscr); } void reconnect() { int a = 0; while (!client.connected()) { a++; digitalWrite(LED, !digitalRead(LED)); //wdt_reset(); Serial.println("WDT reset"); if (client.connect("elcounter")) { digitalWrite(LED, LOW); Public(); } else { delay(10000); } if (a >= 10) { // wdt_enable(WDTO_1S); Serial.println("WDTO_1S"); } } } ! void loop() { // wdt_reset(); Serial.println("WDT_reset"); client.loop(); if (!client.connected()) { reconnect(); } ! if (analogRead(PWR_CTRL) < 1000) { digitalWrite(LED, LOW); save(); delay(10000); } ! if (strComplete) { digitalWrite(LED, !digitalRead(LED)); cmd.toCharArray(buffer, 100); cnt = atoi(strtok(buffer, ";")); pwr = atoi(strtok(NULL, ";")); amp = atoi(strtok(NULL, ";")); bounce = atoi(strtok(NULL, ";")); num = atoi(strtok(NULL, ";")); error = atoi(strtok(NULL, ";")); client.publish(topic_raw, StrToChar(cmd)); cmd = ""; strComplete = false; } ! if (millis() - prevMillis >= poll) { // wdt_reset(); Serial.println("WDT_reset"); prevMillis = millis(); if (cnt != prev_cnt || pwr != prev_pwr || amp != prev_amp) { prev_cnt = cnt; prev_pwr = pwr; prev_amp = amp; client.publish(topic_cnt, IntToChar(cnt)); client.publish(topic_pwr, IntToChar(pwr)); client.publish(topic_amp, IntToChar(amp)); } if (num != prev_num || bounce != prev_bounce) { prev_num = num; prev_bounce = bounce; client.publish(topic_num, IntToChar(num)); client.publish(topic_bounce, IntToChar(bounce)); } if (error > 0) { client.publish(topic_err, "err"); } else { client.publish(topic_err, " "); } } }</avr></eeprom.h></pubsubclient.h></ethernet.h></spi.h>
код с моими правками[/i][/i][/i][/i]

instalator

~~@smoker_vvo:~~

Доброго времени…

Появилось время заниматься проектом дальше. и вот какие проблемы, если с WDT я поступил грубо, просто закоментил его, то с ethernetom вообще ни чего не могу понять. Учитывая что у тебя была другая карта, использую библиотеку для своей.... и ничего не работает....

1. ping - ни чего нет

2. соответсвенно в IOBе то же тишина.

заливал другие скетчи - с сетевой проблем нет.

вот код :

! `#include <spi.h> #include <ethernet.h> #include <pubsubclient.h> #include <eeprom.h> //#include <avr wdt.h=""> ! #define PWR_CTRL A2 //Контроль напряжения #define LED 9 //Светодиод #define CHK_ADR 100 #define CNT_ADR 10 #define PWR_ADR 20 #define POLL_ADR 30 #define RATIO_ADR 40 ! const char* topic_err = "myhome/elcounter/error"; const char* topic_cnt = "myhome/elcounter/count"; const char* topic_pwr = "myhome/elcounter/power"; const char* topic_amp = "myhome/elcounter/amp"; const char* topic_save = "myhome/elcounter/save"; const char* topic_correction = "myhome/elcounter/correction"; const char* topic_connection = "myhome/elcounter/connection"; const char* topic_ip = "myhome/elcounter/config/ip"; const char* topic_polling = "myhome/elcounter/config/polling"; const char* topic_bounce = "myhome/elcounter/config/bounce"; const char* topic_num = "myhome/elcounter/config/num"; const char* topic_reset = "myhome/elcounter/config/reset"; const char* topic_raw = "myhome/elcounter/RAW"; const char* subscr = "myhome/elcounter/#"; ! byte mac[] = { 0xDE, 0xAD, 0xBE, 0xE4, 0xDE, 0x35 }; byte ip[] = { 192, 168, 0, 89}; byte server[] = { 192, 168, 0, 15}; ! unsigned long cnt = 0; unsigned long prev_cnt = 2; unsigned long pwr = 0; unsigned long prev_pwr = 2; int amp = 0; int prev_amp = 2; int num = 0; int prev_num; int bounce = 10; int prev_bounce; int chk = 0; int chk_S = 0; unsigned long prevMillis = 0; unsigned long prevMillis_cnt = 0; int poll = 5000; bool error = 0; String cmd = ""; bool strComplete = false; char buf [50]; char buffer[100]; char s[16]; ! //////////////////////////////////////////////////////////////////////////// void callback(char* topic, byte* payload, unsigned int length) { payload[length] = '\0'; String strTopic = String(topic); String strPayload = String((char*)payload); callback_iobroker(strTopic, strPayload); } ! EthernetClient ethClient; PubSubClient client(server, 1883, callback, ethClient); ! void setup() { MCUSR = 0; // wdt_disable(); Serial.println("WDT_disable"); cmd.reserve(100); delay(10000); Serial.begin(57600); Serial.println("Starting......"); ! if (EEPROM.read(1) != 99) { //Если первый запуск EEPROM.write(1, 99); for (int i = 0 ; i < 4; i++) { EEPROM.write(110 + i, ip[i]); } for (int i = 0 ; i < 4; i++) { EEPROM.write(120 + i, server[i]); } } else { chk = EEPROMReadInt(CHK_ADR); cnt = EEPROMReadLong(CNT_ADR); poll = EEPROMReadInt(POLL_ADR); chk_S = poll - 500; if (chk != chk_S) { error = 2; } for (int i = 0; i < 4; i++) { ip[i] = EEPROM.read(110 + i); } for (int i = 0; i < 4; i++) { server[i] = EEPROM.read(120 + i); } } ! pinMode(LED, OUTPUT); ! // client.setServer(server, 1883); // client.setCallback(callback); Ethernet.begin(mac, ip); delay(200); //wdt_enable(WDTO_8S); Serial.println("WDTO_8S"); if (client.connect("elcounter")) { digitalWrite(LED, LOW); Public(); } } ! void serialEvent() { while (Serial.available() > 0) { char inChar = (char)Serial.read(); cmd += inChar; if (inChar == '\n') { strComplete = true; } } } ! void callback_iobroker(String strTopic, String strPayload) { if (strTopic == topic_correction) { cnt = atol((strPayload).c_str()); Serial.print("SC"); Serial.println(cnt); client.publish(topic_correction, "0"); } else if (strTopic == topic_save) { if (strPayload == "true") { Serial.println("SS"); save(); client.publish(topic_save, "false"); } } else if (strTopic == topic_polling) { poll = strPayload.toInt(); if (poll < 1000) { poll = 1000; } else if (poll > 32767) { poll = 32767; } EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации client.publish(topic_polling, IntToChar(poll)); } else if (strTopic == topic_reset) { if (strPayload == "true") { client.publish(topic_reset, "false"); // reboot(); Serial.println("Reboot"); } } else if (strTopic == topic_bounce) { bounce = strPayload.toInt(); if (bounce < 0) { bounce = 0; } else if (bounce > 10000) { bounce = 10000; } Serial.print("SB"); Serial.println(bounce); client.publish(topic_bounce, IntToChar(bounce)); } else if (strTopic == topic_num) { num = strPayload.toInt(); if (num < 0) { num = 0; } else if (num > 32767) { num = 32767; } Serial.print("SN"); Serial.println(num); client.publish(topic_num, IntToChar(num)); } } ! void save() { chk = poll - 500; EEPROMWriteLong(CNT_ADR, cnt); //Пишем показания счетчика в eeprom из переменной EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации EEPROMWriteInt(CHK_ADR, chk); //чек } ! void reboot() { save(); delay(500); // wdt_enable(WDTO_1S); Serial.println("void reboot"); for (;;) {} } ! char* StrToChar (String str) { int length = str.length(); str.toCharArray(buf, length + 1); return buf; } ! void EEPROMWriteLong(int p_address, unsigned long p_value) { byte four = (p_value & 0xFF); byte three = ((p_value >> 8) & 0xFF); byte two = ((p_value >> 16) & 0xFF); byte one = ((p_value >> 24) & 0xFF); EEPROM.write(p_address, four); EEPROM.write(p_address + 1, three); EEPROM.write(p_address + 2, two); EEPROM.write(p_address + 3, one); } ! unsigned long EEPROMReadLong(int p_address) { long four = EEPROM.read(p_address); long three = EEPROM.read(p_address + 1); long two = EEPROM.read(p_address + 2); long one = EEPROM.read(p_address + 3); return ((four << 0) & 0xFF) + ((three << 8) & 0xFFFF) + ((two << 16) & 0xFFFFFF) + ((one << 24) & 0xFFFFFFFF); } ! void EEPROMWriteInt(int p_address, int p_value) { byte lowByte = ((p_value >> 0) & 0xFF); byte highByte = ((p_value >> 8) & 0xFF); EEPROM.write(p_address, lowByte); EEPROM.write(p_address + 1, highByte); } unsigned int EEPROMReadInt(int p_address) { byte lowByte = EEPROM.read(p_address); byte highByte = EEPROM.read(p_address + 1); return ((lowByte << 0) & 0xFF) + ((highByte << 8) & 0xFF00); } ! char* IntToChar (unsigned long a) { sprintf(buf, "%lu", a); return buf; } ! void Public() { sprintf(s, "%d.%d.%d.%d", ip[0], ip[1], ip[2], ip[3]); client.publish(topic_err, " "); client.publish(topic_cnt, IntToChar(cnt)); client.publish(topic_pwr, IntToChar(pwr)); client.publish(topic_amp, IntToChar(amp)); client.publish(topic_save, "false"); client.publish(topic_correction, "0"); client.publish(topic_connection, "true"); client.publish(topic_ip, s); client.publish(topic_polling, IntToChar(poll)); client.publish(topic_bounce, IntToChar(bounce)); client.publish(topic_num, IntToChar(num)); client.publish(topic_reset, "false"); client.subscribe(subscr); } void reconnect() { int a = 0; while (!client.connected()) { a++; digitalWrite(LED, !digitalRead(LED)); //wdt_reset(); Serial.println("WDT reset"); if (client.connect("elcounter")) { digitalWrite(LED, LOW); Public(); } else { delay(10000); } if (a >= 10) { // wdt_enable(WDTO_1S); Serial.println("WDTO_1S"); } } } ! void loop() { // wdt_reset(); Serial.println("WDT_reset"); client.loop(); if (!client.connected()) { reconnect(); } ! if (analogRead(PWR_CTRL) < 1000) { digitalWrite(LED, LOW); save(); delay(10000); } ! if (strComplete) { digitalWrite(LED, !digitalRead(LED)); cmd.toCharArray(buffer, 100); cnt = atoi(strtok(buffer, ";")); pwr = atoi(strtok(NULL, ";")); amp = atoi(strtok(NULL, ";")); bounce = atoi(strtok(NULL, ";")); num = atoi(strtok(NULL, ";")); error = atoi(strtok(NULL, ";")); client.publish(topic_raw, StrToChar(cmd)); cmd = ""; strComplete = false; } ! if (millis() - prevMillis >= poll) { // wdt_reset(); Serial.println("WDT_reset"); prevMillis = millis(); if (cnt != prev_cnt || pwr != prev_pwr || amp != prev_amp) { prev_cnt = cnt; prev_pwr = pwr; prev_amp = amp; client.publish(topic_cnt, IntToChar(cnt)); client.publish(topic_pwr, IntToChar(pwr)); client.publish(topic_amp, IntToChar(amp)); } if (num != prev_num || bounce != prev_bounce) { prev_num = num; prev_bounce = bounce; client.publish(topic_num, IntToChar(num)); client.publish(topic_bounce, IntToChar(bounce)); } if (error > 0) { client.publish(topic_err, "err"); } else { client.publish(topic_err, " "); } } }</avr></eeprom.h></pubsubclient.h></ethernet.h></spi.h>` код с моими правками Вроде все норм по сети, в логе тишина? ! byte ip[] = { 192, 168, 0, 89}; айпи самой ардуины ! byte server[] = { 192, 168, 0, 15}; айпи mqtt сервера[/i][/i][/i][/i] `

smoker_vvo

А не может быть связанным как то с удаленным конфигом сетевого адреса??

const char* topic_ip = "myhome/elcounter/config/ip";

Заливал этот код в Дуню - все работает…

! ```
`#include <spi.h> // Ethernet shield
#include <ethernet.h> // Ethernet shield
#include <pubsubclient.h> // MQTT
#include <servo.h>
#include <dht.h>
#include <onewire.h>
#include <dallastemperature.h>
Servo servo;
! byte mac[] = { 0xC1, 0x7C, 0x38, 0x41, 0x89, 0x35 };
byte server[] = { 192, 168, 0, 11 }; //IP Брокера
byte ip[] = { 192, 168, 0, 89 }; //IP Клиента (Arduino)
! ////////////////////////////////////////////////////////////////////////////
void callback(char* topic, byte* payload, unsigned int length) {
payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
String strTopic = String(topic);
String strPayload = String((char*)payload);
// Serial.println(strPayload);
callback_iobroker(strTopic, strPayload);
}
! EthernetClient ethClient;
PubSubClient client(server, 1883, callback, ethClient);
#define id_connect "myhome-temp"
#define id_connect "myhome-status"
#define Prefix_subscribe "myhome/Temp/"
#define Prefix_subscribe "myhome/Status/"
! ///////////////Объявляем порты ввода-вывода
#define ServoPin 3 //Порт к которому подключен сервопривод
! const int start_DI_pin []= {2, 4, 5}; // Порты Ввода
int n_DI_pin = sizeof(start_DI_pin) / sizeof(start_DI_pin[0])-1; //Вычисляем длинну массива
! const int start_DO_pin []= {6, 7}; //Порты Вывода
int n_DO_pin = sizeof(start_DO_pin) / sizeof(start_DO_pin[0])-1; //Вычисляем длинну массива
! int DI[] = {0, 0, 0};
int old_DI[] = {0, 0, 0};
! ///////////////////////////Переменные для работы с освещением//////////////////////////////////////
int ServoAngle = 100; //Угол сервопривода при включении
int flag = 0;
int flag2 = 0;
int pause = 0;
! //------------------------------------------- Sensors -------------------------------------------//
const int MQ7_Pin = A0; // Куда подключили MQ7
//int MQ7Value = 0;
int MQ7Value = analogRead(MQ7_Pin);

const int foto_Pin = A1; // устанавливаем входную ногу для Фоторезистора
//unsigned int fotoValue = 0; // цифровое значение фоторезистора
unsigned int fotoValue = analogRead(foto_Pin);

! #define ONE_WIRE_BUS 8
//#define TEMPERATURE_PRECISION 9
OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature DS_sensors(&oneWire);
// 28 80 E9 3A 04 00 00 10
//T0:28 88 AD D7 02 00 00 42
//T1:28 14 A5 D7 02 00 00 B0
//T2:28 72 26 7B 04 00 00 2E
//T3:28 CA 1A 3B 04 00 00 CD
//T4:28 E6 D5 D7 02 00 00 C1
//T5:28 16 B4 7A 04 00 00 8A
//T6:28 2B 86 D7 02 00 00 CF
//T7:28 AB 9D D7 02 00 00 29
DeviceAddress addr_T1 = { 0x28, 0x80, 0xE9, 0x3A, 0x4, 0x0, 0x0, 0x10 };//кладовка
DeviceAddress addr_T2 = { 0x28, 0x88, 0xAD, 0xD7, 0x2, 0x0, 0x0, 0x42 };//кухня
DeviceAddress addr_T3 = { 0x28, 0x14, 0xA5, 0xD7, 0x2, 0x0, 0x0, 0xB0 };//детская
DeviceAddress addr_T4 = { 0x28, 0x72, 0x26, 0x7B, 0x4, 0x0, 0x0, 0x2E };//гараж
DeviceAddress addr_T5 = { 0x28, 0xCA, 0x1A, 0x3B, 0x4, 0x0, 0x0, 0xCD };//ванная
DeviceAddress addr_T6 = { 0x28, 0xE6, 0xD5, 0xD7, 0x2, 0x0, 0x0, 0xC1 };//улица
DeviceAddress addr_T7 = { 0x28, 0x16, 0xB4, 0x7A, 0x4, 0x0, 0x0, 0x8A };//спальня2
DeviceAddress addr_T8 = { 0x28, 0x2B, 0x86, 0xD7, 0x2, 0x0, 0x0, 0xCF };//зал
DeviceAddress addr_T9 = { 0x28, 0xAB, 0x9D, 0xD7, 0x2, 0x0, 0x0, 0x29 };//мансарда
! float T1=0;
float T2=0;
float T3=0;
float T4=0;
float T5=0;
float T6=0;
float T7=0;
float T8=0;
float T9=0;
! //dht DHT;
//#define DHT22_PIN 9
//float Hout = 0;
//float Tout = 0;
! ////////////////////////////////////////////////////////////////////////////
//void callback(char* topic, byte* payload, unsigned int length) {
// payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
// String strTopic = String(topic);
// String strPayload = String((char*)payload);
// Serial.println(strPayload);
// callback_iobroker(strTopic, strPayload);
//}
////////////////////////////////////////////////////////////////////////////
void setup() {
Serial.begin(57600);
Serial.println("start");

Serial.print("Locating devices...");
DS_sensors.begin();
Serial.print("Found ");
Serial.print(DS_sensors.getDeviceCount(), DEC);
Serial.println(" devices.");

! // report parasite power requirements
Serial.print("Parasite power is: ");
if (DS_sensors.isParasitePowerMode()) Serial.println("ON");
else Serial.println("OFF");

//Объявляем порты Digital inputs/outputs

for(int i=0 ;i<=n_DI_pin; i++) { pinMode (start_DI_pin [i], INPUT); }
digitalWrite(5, HIGH); //Насос скважины
digitalWrite(4, HIGH); //Электрика
for(int i=0 ;i<=n_DO_pin; i++) { pinMode (start_DO_pin [i], OUTPUT); }

! Ethernet.begin(mac, ip);
if (client.connect(id_connect)) {
getSensors();
control();
//client.publish("myhome/Kitchen/Change_Counter", "0");
//client.publish("myhome/Kitchen/Temp_room", "0");
//client.publish("myhome/Kitchen/Humidity_room", "0");
client.publish("myhome/Temp/Kladovka", "0");
client.publish("myhome/Temp/Kitchen", "0");
client.publish("myhome/Temp/Detskaya", "0");
client.publish("myhome/Temp/Garage", "0");
client.publish("myhome/Temp/Street", "0");
client.publish("myhome/Temp/Spalnya2", "0");
client.publish("myhome/Temp/Zal", "0");
client.publish("myhome/Temp/Mansarda", "0");
client.publish("myhome/Temp/Vannaya", "0");

//client.publish("myhome/Kitchen/Lux", "0");
//client.publish("myhome/Kitchen/Servo", "0");
client.publish("myhome/Temp/MQ7", "0");

client.publish("myhome/Status/Power", "0");
client.publish("myhome/Status/Pompe", "0");

client.subscribe("myhome/Temp/#");
client.subscribe("myhome/Status/#");

}
}
/////////////////////////////////////////////////////////////////////////
void loop() {
client.loop();
control();
getSensors();
if (!client.connected()) {
if (client.connect(id_connect)) {
control();
getSensors();
client.subscribe("myhome/Temp/#");
}
}
}</dallastemperature.h></onewire.h></dht.h></servo.h></pubsubclient.h></ethernet.h></spi.h>`

! и все пингуется, а вот заливаю счетчик - и фиг-вам.... пинг не проходит....[/i][/i]

smoker_vvo

В свое время натыкался на проблемы с СД картами и W5100

instalator

~~@smoker_vvo:~~

А не может быть связанным как то с удаленным конфигом сетевого адреса??

const char* topic_ip = "myhome/elcounter/config/ip";

Заливал этот код в Дуню - все работает…

! ```
`#include <spi.h> // Ethernet shield
#include <ethernet.h> // Ethernet shield
#include <pubsubclient.h> // MQTT
#include <servo.h>
#include <dht.h>
#include <onewire.h>
#include <dallastemperature.h>
Servo servo;
! byte mac[] = { 0xC1, 0x7C, 0x38, 0x41, 0x89, 0x35 };
byte server[] = { 192, 168, 0, 11 }; //IP Брокера
byte ip[] = { 192, 168, 0, 89 }; //IP Клиента (Arduino)
! ////////////////////////////////////////////////////////////////////////////
void callback(char* topic, byte* payload, unsigned int length) {
payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
String strTopic = String(topic);
String strPayload = String((char*)payload);
// Serial.println(strPayload);
callback_iobroker(strTopic, strPayload);
}
! EthernetClient ethClient;
PubSubClient client(server, 1883, callback, ethClient);
#define id_connect "myhome-temp"
#define id_connect "myhome-status"
#define Prefix_subscribe "myhome/Temp/"
#define Prefix_subscribe "myhome/Status/"
! ///////////////Объявляем порты ввода-вывода
#define ServoPin 3 //Порт к которому подключен сервопривод
! const int start_DI_pin []= {2, 4, 5}; // Порты Ввода
int n_DI_pin = sizeof(start_DI_pin) / sizeof(start_DI_pin[0])-1; //Вычисляем длинну массива
! const int start_DO_pin []= {6, 7}; //Порты Вывода
int n_DO_pin = sizeof(start_DO_pin) / sizeof(start_DO_pin[0])-1; //Вычисляем длинну массива
! int DI[] = {0, 0, 0};
int old_DI[] = {0, 0, 0};
! ///////////////////////////Переменные для работы с освещением//////////////////////////////////////
int ServoAngle = 100; //Угол сервопривода при включении
int flag = 0;
int flag2 = 0;
int pause = 0;
! //------------------------------------------- Sensors -------------------------------------------//
const int MQ7_Pin = A0; // Куда подключили MQ7
//int MQ7Value = 0;
int MQ7Value = analogRead(MQ7_Pin);

const int foto_Pin = A1; // устанавливаем входную ногу для Фоторезистора
//unsigned int fotoValue = 0; // цифровое значение фоторезистора
unsigned int fotoValue = analogRead(foto_Pin);

! #define ONE_WIRE_BUS 8
//#define TEMPERATURE_PRECISION 9
OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature DS_sensors(&oneWire);
// 28 80 E9 3A 04 00 00 10
//T0:28 88 AD D7 02 00 00 42
//T1:28 14 A5 D7 02 00 00 B0
//T2:28 72 26 7B 04 00 00 2E
//T3:28 CA 1A 3B 04 00 00 CD
//T4:28 E6 D5 D7 02 00 00 C1
//T5:28 16 B4 7A 04 00 00 8A
//T6:28 2B 86 D7 02 00 00 CF
//T7:28 AB 9D D7 02 00 00 29
DeviceAddress addr_T1 = { 0x28, 0x80, 0xE9, 0x3A, 0x4, 0x0, 0x0, 0x10 };//кладовка
DeviceAddress addr_T2 = { 0x28, 0x88, 0xAD, 0xD7, 0x2, 0x0, 0x0, 0x42 };//кухня
DeviceAddress addr_T3 = { 0x28, 0x14, 0xA5, 0xD7, 0x2, 0x0, 0x0, 0xB0 };//детская
DeviceAddress addr_T4 = { 0x28, 0x72, 0x26, 0x7B, 0x4, 0x0, 0x0, 0x2E };//гараж
DeviceAddress addr_T5 = { 0x28, 0xCA, 0x1A, 0x3B, 0x4, 0x0, 0x0, 0xCD };//ванная
DeviceAddress addr_T6 = { 0x28, 0xE6, 0xD5, 0xD7, 0x2, 0x0, 0x0, 0xC1 };//улица
DeviceAddress addr_T7 = { 0x28, 0x16, 0xB4, 0x7A, 0x4, 0x0, 0x0, 0x8A };//спальня2
DeviceAddress addr_T8 = { 0x28, 0x2B, 0x86, 0xD7, 0x2, 0x0, 0x0, 0xCF };//зал
DeviceAddress addr_T9 = { 0x28, 0xAB, 0x9D, 0xD7, 0x2, 0x0, 0x0, 0x29 };//мансарда
! float T1=0;
float T2=0;
float T3=0;
float T4=0;
float T5=0;
float T6=0;
float T7=0;
float T8=0;
float T9=0;
! //dht DHT;
//#define DHT22_PIN 9
//float Hout = 0;
//float Tout = 0;
! ////////////////////////////////////////////////////////////////////////////
//void callback(char* topic, byte* payload, unsigned int length) {
// payload[length] = '\0';
// Serial.print(topic);
// Serial.print("=");
// String strTopic = String(topic);
// String strPayload = String((char*)payload);
// Serial.println(strPayload);
// callback_iobroker(strTopic, strPayload);
//}
////////////////////////////////////////////////////////////////////////////
void setup() {
Serial.begin(57600);
Serial.println("start");

Serial.print("Locating devices...");
DS_sensors.begin();
Serial.print("Found ");
Serial.print(DS_sensors.getDeviceCount(), DEC);
Serial.println(" devices.");

! // report parasite power requirements
Serial.print("Parasite power is: ");
if (DS_sensors.isParasitePowerMode()) Serial.println("ON");
else Serial.println("OFF");
//Объявляем порты Digital inputs/outputs
for(int i=0 ;i<=n_DI_pin; i++) { pinMode (start_DI_pin [i], INPUT); }
digitalWrite(5, HIGH); //Насос скважины
digitalWrite(4, HIGH); //Электрика
for(int i=0 ;i<=n_DO_pin; i++) { pinMode (start_DO_pin [i], OUTPUT); }

! Ethernet.begin(mac, ip);
if (client.connect(id_connect)) {
getSensors();
control();
//client.publish("myhome/Kitchen/Change_Counter", "0");
//client.publish("myhome/Kitchen/Temp_room", "0");
//client.publish("myhome/Kitchen/Humidity_room", "0");
client.publish("myhome/Temp/Kladovka", "0");
client.publish("myhome/Temp/Kitchen", "0");
client.publish("myhome/Temp/Detskaya", "0");
client.publish("myhome/Temp/Garage", "0");
client.publish("myhome/Temp/Street", "0");
client.publish("myhome/Temp/Spalnya2", "0");
client.publish("myhome/Temp/Zal", "0");
client.publish("myhome/Temp/Mansarda", "0");
client.publish("myhome/Temp/Vannaya", "0");
//client.publish("myhome/Kitchen/Lux", "0");
//client.publish("myhome/Kitchen/Servo", "0");
client.publish("myhome/Temp/MQ7", "0");

client.publish("myhome/Status/Power", "0");
client.publish("myhome/Status/Pompe", "0");

client.subscribe("myhome/Temp/#");
client.subscribe("myhome/Status/#");
}
}
/////////////////////////////////////////////////////////////////////////
void loop() {
client.loop();
control();
getSensors();
if (!client.connected()) {
if (client.connect(id_connect)) {
control();
getSensors();
client.subscribe("myhome/Temp/#");
}
}
}</dallastemperature.h></onewire.h></dht.h></servo.h></pubsubclient.h></ethernet.h></spi.h>`

! и все пингуется, а вот заливаю счетчик - и фиг-вам.... пинг не проходит....нет, вечером будет время проверю твой код[/i][/i]
``` `

smoker_vvo

ок.

а я еще с твоим по колдую…..

instalator

~~@smoker_vvo:~~

ок.

а я еще с твоим по колдую….. `

! ```
`#include <spi.h>
#include <ethernet.h>
#include <pubsubclient.h>
#include <eeprom.h>
//#include <avr wdt.h="">
! #define PWR_CTRL A2 //Контроль напряжения
#define LED 9 //Светодиод
#define CHK_ADR 100
#define CNT_ADR 10
#define PWR_ADR 20
#define POLL_ADR 30
#define RATIO_ADR 40
! const char* topic_err = "myhome/test/error";
const char* topic_cnt = "myhome/test/count";
const char* topic_pwr = "myhome/test/power";
const char* topic_amp = "myhome/test/amp";
const char* topic_save = "myhome/test/save";
const char* topic_correction = "myhome/test/correction";
const char* topic_connection = "myhome/test/connection";
const char* topic_ip = "myhome/test/config/ip";
const char* topic_polling = "myhome/test/config/polling";
const char* topic_bounce = "myhome/test/config/bounce";
const char* topic_num = "myhome/test/config/num";
const char* topic_reset = "myhome/test/config/reset";
const char* topic_raw = "myhome/test/RAW";
const char* subscr = "myhome/test/#";
! byte mac[] = { 0xDE, 0xA3, 0xBE, 0xE4, 0xDE, 0x35 };
byte ip[] = { 192, 168, 1, 59};
byte server[] = { 192, 168, 1, 190};
! unsigned long cnt = 0;
unsigned long prev_cnt = 2;
unsigned long pwr = 0;
unsigned long prev_pwr = 2;
int amp = 0;
int prev_amp = 2;
int num = 0;
int prev_num;
int bounce = 10;
int prev_bounce;
int chk = 0;
int chk_S = 0;
unsigned long prevMillis = 0;
unsigned long prevMillis_cnt = 0;
int poll = 5000;
bool error = 0;
String cmd = "";
bool strComplete = false;
char buf [50];
char buffer[100];
char s[16];
! ////////////////////////////////////////////////////////////////////////////
void callback(char* topic, byte* payload, unsigned int length) {
payload[length] = '\0';
String strTopic = String(topic);
String strPayload = String((char*)payload);
callback_iobroker(strTopic, strPayload);
}
! EthernetClient ethClient;
PubSubClient client(ethClient);
! void setup() {
Serial.begin(57600);
//MCUSR = 0;
// wdt_disable();
Serial.println("WDT_disable");
cmd.reserve(100);
delay(10000);

Serial.println("Starting......");

! if (EEPROM.read(1) != 99) { //Если первый запуск
EEPROM.write(1, 99);
for (int i = 0 ; i < 4; i++) {
EEPROM.write(110 + i, ip[i]);
}
for (int i = 0 ; i < 4; i++) {
EEPROM.write(120 + i, server[i]);
}
} else {
chk = EEPROMReadInt(CHK_ADR);
cnt = EEPROMReadLong(CNT_ADR);
poll = EEPROMReadInt(POLL_ADR);
chk_S = poll - 500;
if (chk != chk_S) {
error = 2;
}
for (int i = 0; i < 4; i++) {
ip[i] = EEPROM.read(110 + i);
}
for (int i = 0; i < 4; i++) {
server[i] = EEPROM.read(120 + i);
}
}
! pinMode(LED, OUTPUT);
! client.setServer(server, 1883);
client.setCallback(callback);
Ethernet.begin(mac, ip);

delay(200);
//wdt_enable(WDTO_8S);
Serial.println("WDTO_8S");
if (client.connect("test")){
digitalWrite(LED, LOW);
Public();
}
}

! void serialEvent() {
while (Serial.available() > 0) {
char inChar = (char)Serial.read();
cmd += inChar;
if (inChar == '\n') {
strComplete = true;
}
}
}
! void loop() {
// wdt_reset();
Serial.println("WDT_reset");
client.loop();
if (!client.connected()) {
reconnect();
}
! /if (analogRead(PWR_CTRL) < 1000) {
digitalWrite(LED, LOW);
save();
delay(10000);
}/
! if (strComplete) {
digitalWrite(LED, !digitalRead(LED));
cmd.toCharArray(buffer, 100);
cnt = atoi(strtok(buffer, ";"));
pwr = atoi(strtok(NULL, ";"));
amp = atoi(strtok(NULL, ";"));
bounce = atoi(strtok(NULL, ";"));
num = atoi(strtok(NULL, ";"));
error = atoi(strtok(NULL, ";"));
client.publish(topic_raw, StrToChar(cmd));
cmd = "";
strComplete = false;
}
! if (millis() - prevMillis >= poll) {
// wdt_reset();
Serial.println("WDT_reset-");
prevMillis = millis();
if (cnt != prev_cnt || pwr != prev_pwr || amp != prev_amp) {
prev_cnt = cnt;
prev_pwr = pwr;
prev_amp = amp;
client.publish(topic_cnt, IntToChar(cnt));
client.publish(topic_pwr, IntToChar(pwr));
client.publish(topic_amp, IntToChar(amp));
}
if (num != prev_num || bounce != prev_bounce) {
prev_num = num;
prev_bounce = bounce;
client.publish(topic_num, IntToChar(num));
client.publish(topic_bounce, IntToChar(bounce));
}
if (error > 0) {
client.publish(topic_err, "err");
} else {
client.publish(topic_err, " ");
}
}
}
! void callback_iobroker(String strTopic, String strPayload) {
if (strTopic == topic_correction) {
cnt = atol((strPayload).c_str());
Serial.print("SC");
Serial.println(cnt);
client.publish(topic_correction, "0");
}
else if (strTopic == topic_save) {
if (strPayload == "true") {
Serial.println("SS");
save();
client.publish(topic_save, "false");
}
}
else if (strTopic == topic_polling) {
poll = strPayload.toInt();
if (poll < 1000) {
poll = 1000;
} else if (poll > 32767) {
poll = 32767;
}
EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации
client.publish(topic_polling, IntToChar(poll));
}
else if (strTopic == topic_reset) {
if (strPayload == "true") {
client.publish(topic_reset, "false");
// reboot();
Serial.println("Reboot");
}
}
else if (strTopic == topic_bounce) {
bounce = strPayload.toInt();
if (bounce < 0) {
bounce = 0;
} else if (bounce > 10000) {
bounce = 10000;
}
Serial.print("SB");
Serial.println(bounce);
client.publish(topic_bounce, IntToChar(bounce));
}
else if (strTopic == topic_num) {
num = strPayload.toInt();
if (num < 0) {
num = 0;
} else if (num > 32767) {
num = 32767;
}
Serial.print("SN");
Serial.println(num);
client.publish(topic_num, IntToChar(num));
}
}
! void save() {
chk = poll - 500;
EEPROMWriteLong(CNT_ADR, cnt); //Пишем показания счетчика в eeprom из переменной
EEPROMWriteInt(POLL_ADR, poll); //Интервал публикации
EEPROMWriteInt(CHK_ADR, chk); //чек
}
! void reboot() {
//save();
//delay(500);
// wdt_enable(WDTO_1S);
Serial.println("void reboot");
//for (;;) {}
}
! char* StrToChar (String str) {
int length = str.length();
str.toCharArray(buf, length + 1);
return buf;
}
! void EEPROMWriteLong(int p_address, unsigned long p_value) {
byte four = (p_value & 0xFF);
byte three = ((p_value >> 8) & 0xFF);
byte two = ((p_value >> 16) & 0xFF);
byte one = ((p_value >> 24) & 0xFF);
EEPROM.write(p_address, four);
EEPROM.write(p_address + 1, three);
EEPROM.write(p_address + 2, two);
EEPROM.write(p_address + 3, one);
}
! unsigned long EEPROMReadLong(int p_address) {
long four = EEPROM.read(p_address);
long three = EEPROM.read(p_address + 1);
long two = EEPROM.read(p_address + 2);
long one = EEPROM.read(p_address + 3);
return ((four << 0) & 0xFF) + ((three << 8) & 0xFFFF) + ((two << 16) & 0xFFFFFF) + ((one << 24) & 0xFFFFFFFF);
}
! void EEPROMWriteInt(int p_address, int p_value) {
byte lowByte = ((p_value >> 0) & 0xFF);
byte highByte = ((p_value >> 8) & 0xFF);
EEPROM.write(p_address, lowByte);
EEPROM.write(p_address + 1, highByte);
}
unsigned int EEPROMReadInt(int p_address) {
byte lowByte = EEPROM.read(p_address);
byte highByte = EEPROM.read(p_address + 1);
return ((lowByte << 0) & 0xFF) + ((highByte << 8) & 0xFF00);
}
! char* IntToChar (unsigned long a) {
sprintf(buf, "%lu", a);
return buf;
}
! void Public() {
sprintf(s, "%d.%d.%d.%d", ip[0], ip[1], ip[2], ip[3]);
client.publish(topic_err, " ");
client.publish(topic_cnt, IntToChar(cnt));
client.publish(topic_pwr, IntToChar(pwr));
client.publish(topic_amp, IntToChar(amp));
client.publish(topic_save, "false");
client.publish(topic_correction, "0");
client.publish(topic_connection, "true");
client.publish(topic_ip, s);
client.publish(topic_polling, IntToChar(poll));
client.publish(topic_bounce, IntToChar(bounce));
client.publish(topic_num, IntToChar(num));
client.publish(topic_reset, "false");
client.subscribe(subscr);
}
void reconnect() {
int a = 0;
while (!client.connected()) {
a++;
digitalWrite(LED, !digitalRead(LED));
//wdt_reset();
Serial.println("WDT reset");
if (client.connect("test")) {
digitalWrite(LED, LOW);
Public();
} else {
delay(10000);
}
if (a >= 10) {
// wdt_enable(WDTO_1S);
Serial.println("WDTO_1S");
}
}
}</avr></eeprom.h></pubsubclient.h></ethernet.h></spi.h>`
Работает[/i][/i][/i][/i]

smoker_vvo

Убейте меня!!! ОН НЕ РАБОТАЕТ….. Ну не пингуется этот ip, я поменял на свои......

instalator

~~@smoker_vvo:~~

Убейте меня!!! ОН НЕ РАБОТАЕТ….. Ну не пингуется этот ip, я поменял на свои...... `
библиотеки последних версии?

smoker_vvo

Начнем с простого…. Какая IDE

smoker_vvo

в IDE 1.5.2 гружу вот этот скетч:

! ````
/*
Web Server

A simple web server that shows the value of the analog input pins.
using an Arduino Wiznet Ethernet shield.

Circuit:

Ethernet shield attached to pins 10, 11, 12, 13
Analog inputs attached to pins A0 through A5 (optional)

created 18 Dec 2009
by David A. Mellis
modified 9 Apr 2012
by Tom Igoe

*/

! #include <spi.h>#include <ethernet.h>// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
IPAddress ip(192,168,0, 89);
! // Initialize the Ethernet server library
// with the IP address and port you want to use
// (port 80 is default for HTTP):
EthernetServer server(80);
! void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for Leonardo only
}
! // start the Ethernet connection and the server:
Ethernet.begin(mac, ip);
server.begin();
Serial.print("server is at ");
Serial.println(Ethernet.localIP());
}
! void loop() {
// listen for incoming clients
EthernetClient client = server.available();
if (client) {
Serial.println("new client");
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected()) {
if (client.available()) {
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank) {
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connection: close");
client.println();
client.println("");
client.println("");
// add a meta refresh tag, so the browser pulls again every 5 seconds:
client.println("");
// output the value of each analog input pin
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
int sensorReading = analogRead(analogChannel);
client.print("analog input ");
client.print(analogChannel);
client.print(" is ");
client.print(sensorReading);
client.println("
");
}
client.println("");
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r') {
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
Serial.println("client disonnected");
}
}</ethernet.h></spi.h>


Пинг - отличный, и веб пускает,

smoker_vvo

в 1ю8ю2 - тоже проблем нет…...

smoker_vvo

1ю6ю13 - полет нормальный

и 1.0.6 - работает…...

Community Forum

NEWS

Скрипт для счётчика

Support us

675

32.5k

81.6k

1.3m