@Atifan
Hi!
Ich weiß der Post ist schon etwas älter. Aber wäre es möglich das Unterteil mit einem 1 1/2 Zoll Gewinde zu versehen?
Bei meinen Rotex Tanks passt das 2 Zoll Gewinde nicht.
Danke für deine Rückmeldung!
Latest posts made by Timo Renz
-
RE: Ölstandsmesser selfmadeposted in Hardware
-
RE: Wasserzähler - Version 2 - all-in-deviceposted in Hardware
@esp8266 said in Wasserzähler - Version 2 - all-in-device:
@beowolf , das wusste aber noch keiner. Ich bleibe bei der alten....sehe kein Grund dafür.
Laüft auf dem einen Strom- und Wasserzähler. Der andere Stromzähler wird mit optischen Impulsgeber gezählt.Wenn die noch keiner getestet hat warum ist sie dann punkt A Stable bzw. Rolling und B über das online Flash tool installierbar?
Also der vorwurf hinkt ....
Welche Version lauft den im Moment am stabilsten?
@esp8266 said in Wasserzähler - Version 2 - all-in-device:
Die Marker wurden nicht gesetzt. Ich kann jedenfalls keine als sowas erkennen. Deshallb kein ausgerichtetes Bild. Sollte die große rote Umrandung ein Marker von 2 dar stellen, ist das falsch.
Ich unterstelle mal, das nicht in der Wiki richtig gelesen wurde.Ok,da gebe ich dir recht, das mit den Markern habe ich falsch verstanden. Wird korrigiert
Vielen dank für die hilfe!!!!
-
RE: Wasserzähler - Version 2 - all-in-deviceposted in Hardware
Hi!
Ich habe mich nun auch mal an das Projekt getraut. Kurz vorab zu meinem setup:
ESP 32 Cam:
Link
Stromversorgung:
Netzteil:
Link
Leitungslänge ca. 15M mit 0,75mm² angeschlossen am USB Port vom Mainboard es hängen noch 3 weitere ESP32 / 8266 mit dran die funktionieren mit der selben Verkabelung.
(Es kommen 5,1V an)Wasserzähler:
sensus IPerlAdapter sind selbst gedruckt
Der ESP wurde via Web mit der aktuellen Version gefascht., Sd karte bespielt ( ist eine uralte 4GB karte Class ???)
Nun zu meine Problemen!
Das Webinterface ist sehr sehr langsam, teilweise so langsam das mir der Browser ein time out anzeigt.Was nicht so schlimm wäre, aber nach einstellen der Kamera und der ROI mit anschließenden Neustart verdreht er das Kamerabild und die ROI punkte sodass nur murks raus kommt.
hier noch ein paar Screenshot nach gefühlten 5 Energy .....
Und hier noch der Log. Was ich gerade sehe, er will etwas senden, MQTT usw. ist noch deaktiviert.
[0d00h00m00s] 2023-11-01T08:42:08 <INF> [MAIN] ================================================= [0d00h00m00s] 2023-11-01T08:42:08 <INF> [MAIN] ==================== Start ====================== [0d00h00m00s] 2023-11-01T08:42:08 <INF> [MAIN] ================================================= [0d00h00m00s] 2023-11-01T08:42:08 <INF> [MAIN] PSRAM size: 8388608 byte (8MB / 64MBit) [0d00h00m00s] 2023-11-01T08:42:08 <INF> [MAIN] Total heap: 4376891 byte [0d00h00m04s] 2023-11-01T08:42:12 <INF> [MAIN] Camera info: PID: 0x26, VER: 0x42, MIDL: 0x7f, MIDH: 0xa2 [0d00h00m04s] 2023-11-01T08:42:12 <INF> [SDCARD] Basic R/W check started... [0d00h00m04s] 2023-11-01T08:42:12 <INF> [SDCARD] Basic R/W check successful [0d00h00m04s] 2023-11-01T08:42:12 <INF> [SNTP] TimeServer: pool.ntp.org [0d00h00m04s] 2023-11-01T08:42:12 <INF> [SNTP] Configuring NTP Client... [0d00h00m04s] 2023-11-01T09:42:12 <INF> [SNTP] Time zone set to CET-1CEST,M3.5.0,M10.5.0/3 [0d00h00m04s] 2023-11-01T09:42:12 <INF> [SNTP] Time is already set: 2023-11-01 09:42:12 [0d00h00m04s] 2023-11-01T09:42:12 <INF> [MAIN] CPU frequency: 160 MHz [0d00h00m05s] 2023-11-01T09:42:13 <INF> [SDCARD] Folder/file presence check started... [0d00h00m05s] 2023-11-01T09:42:13 <INF> [SDCARD] Folder/file presence check successful [0d00h00m05s] 2023-11-01T09:42:13 <INF> [MAIN] Tag: 'v15.3.0', Release: v15.3.0 (Commit: 3fbff0a), Date/Time: 2023-07-22 09:42, Web UI: Release: v15.3.0 (Commit: 3fbff0a) [0d00h00m05s] 2023-11-01T09:42:13 <INF> [MAIN] Reset reason: Via esp_restart [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WLANINI] SSID: renz [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WLANINI] Password: XXXXXXXX [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WLANINI] Hostname: wasserzähler [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WLANINI] IP-Address: 192.168.178.45 [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WLANINI] Gateway: 192.168.178.1 [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WLANINI] Netmask: 255.255.255.0 [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WLANINI] RSSIThreshold: -75 [0d00h00m05s] 2023-11-01T09:42:13 <INF> [MAIN] WLAN config loaded, init WIFI... [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WIFI] Manual interface config -> IP: 192.168.178.45, Gateway: 192.168.178.1, Netmask: 255.255.255.0 [0d00h00m05s] 2023-11-01T09:42:13 <INF> [WIFI] No DNS server, use gateway [0d00h00m05s] 2023-11-01T09:42:14 <INF> [WIFI] Set hostname to: wasserzähler [0d00h00m05s] 2023-11-01T09:42:14 <INF> [WIFI] Init successful [0d00h00m09s] 2023-11-01T09:42:17 <INF> [WIFI] Connected to: renz, RSSI: -53 [0d00h00m09s] 2023-11-01T09:42:17 <INF> [WIFI] Assigned IP: 192.168.178.45 [0d00h00m25s] 2023-11-01T09:42:34 <INF> [MAIN] Device info: CPU cores: 2, Chip revision: 300 [0d00h00m25s] 2023-11-01T09:42:34 <INF> [MAIN] SD card info: Name: SU16G, Capacity: 15193MB, Free: 15175MB [0d00h00m27s] 2023-11-01T09:42:36 <INF> [MAIN] Initialization completed successfully [0d00h00m29s] 2023-11-01T09:42:38 <INF> [LOGFILE] Set log level to ERROR [0d00h01m20s] 2023-11-01T09:43:28 <ERR> [POSTPROC] Zähler: Raw: 477617200, Value: , Status: Rate too high - Read: 477617200 - Pre: 241563 - Rate: 477375637 [0d00h00m00s] 2023-11-01T08:44:06 <INF> [MAIN] ================================================= [0d00h00m00s] 2023-11-01T08:44:06 <INF> [MAIN] ==================== Start ====================== [0d00h00m00s] 2023-11-01T08:44:06 <INF> [MAIN] ================================================= [0d00h00m00s] 2023-11-01T08:44:06 <INF> [MAIN] PSRAM size: 8388608 byte (8MB / 64MBit) [0d00h00m00s] 2023-11-01T08:44:06 <INF> [MAIN] Total heap: 4376759 byte [0d00h00m04s] 2023-11-01T08:44:10 <INF> [MAIN] Camera info: PID: 0x26, VER: 0x42, MIDL: 0x7f, MIDH: 0xa2 [0d00h00m04s] 2023-11-01T08:44:10 <INF> [SDCARD] Basic R/W check started... [0d00h00m04s] 2023-11-01T08:44:10 <INF> [SDCARD] Basic R/W check successful [0d00h00m04s] 2023-11-01T08:44:10 <INF> [SNTP] TimeServer: pool.ntp.org [0d00h00m04s] 2023-11-01T08:44:10 <INF> [SNTP] Configuring NTP Client... [0d00h00m04s] 2023-11-01T09:44:10 <INF> [SNTP] Time zone set to CET-1CEST,M3.5.0,M10.5.0/3 [0d00h00m04s] 2023-11-01T09:44:10 <INF> [SNTP] Time is already set: 2023-11-01 09:44:10 [0d00h00m04s] 2023-11-01T09:44:10 <INF> [MAIN] CPU frequency: 160 MHz [0d00h00m05s] 2023-11-01T09:44:11 <INF> [SDCARD] Folder/file presence check started... [0d00h00m05s] 2023-11-01T09:44:11 <INF> [SDCARD] Folder/file presence check successful [0d00h00m05s] 2023-11-01T09:44:11 <INF> [MAIN] Tag: 'v15.3.0', Release: v15.3.0 (Commit: 3fbff0a), Date/Time: 2023-07-22 09:42, Web UI: Release: v15.3.0 (Commit: 3fbff0a) [0d00h00m05s] 2023-11-01T09:44:11 <INF> [MAIN] Reset reason: Via esp_restart [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WLANINI] SSID: renz [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WLANINI] Password: XXXXXXXX [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WLANINI] Hostname: wasserzähler [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WLANINI] IP-Address: 192.168.178.45 [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WLANINI] Gateway: 192.168.178.1 [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WLANINI] Netmask: 255.255.255.0 [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WLANINI] RSSIThreshold: -75 [0d00h00m05s] 2023-11-01T09:44:11 <INF> [MAIN] WLAN config loaded, init WIFI... [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WIFI] Manual interface config -> IP: 192.168.178.45, Gateway: 192.168.178.1, Netmask: 255.255.255.0 [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WIFI] No DNS server, use gateway [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WIFI] Set hostname to: wasserzähler [0d00h00m05s] 2023-11-01T09:44:11 <INF> [WIFI] Init successful [0d00h00m08s] 2023-11-01T09:44:14 <INF> [WIFI] Connected to: renz, RSSI: -53 [0d00h00m08s] 2023-11-01T09:44:14 <INF> [WIFI] Assigned IP: 192.168.178.45 [0d00h00m25s] 2023-11-01T09:44:31 <INF> [MAIN] Device info: CPU cores: 2, Chip revision: 300 [0d00h00m25s] 2023-11-01T09:44:31 <INF> [MAIN] SD card info: Name: SU16G, Capacity: 15193MB, Free: 15175MB [0d00h00m27s] 2023-11-01T09:44:33 <INF> [MAIN] Initialization completed successfully [0d00h00m29s] 2023-11-01T09:44:35 <INF> [LOGFILE] Set log level to ERROR [0d00h01m19s] 2023-11-01T09:45:25 <ERR> [POSTPROC] Zähler: Raw: 777167406000, Value: , Status: Rate too high - Read: 2147483647 - Pre: 241563 - Rate: 2147483647 [0d00h00m00s] 2023-11-01T08:47:27 <INF> [MAIN] ================================================= [0d00h00m00s] 2023-11-01T08:47:27 <INF> [MAIN] ==================== Start ====================== [0d00h00m00s] 2023-11-01T08:47:27 <INF> [MAIN] ================================================= [0d00h00m00s] 2023-11-01T08:47:27 <INF> [MAIN] PSRAM size: 8388608 byte (8MB / 64MBit) [0d00h00m00s] 2023-11-01T08:47:27 <INF> [MAIN] Total heap: 4376891 byte [0d00h00m04s] 2023-11-01T08:47:31 <INF> [MAIN] Camera info: PID: 0x26, VER: 0x42, MIDL: 0x7f, MIDH: 0xa2 [0d00h00m04s] 2023-11-01T08:47:31 <INF> [SDCARD] Basic R/W check started... [0d00h00m04s] 2023-11-01T08:47:31 <INF> [SDCARD] Basic R/W check successful [0d00h00m04s] 2023-11-01T08:47:31 <INF> [SNTP] TimeServer: pool.ntp.org [0d00h00m04s] 2023-11-01T08:47:31 <INF> [SNTP] Configuring NTP Client... [0d00h00m04s] 2023-11-01T09:47:31 <INF> [SNTP] Time zone set to CET-1CEST,M3.5.0,M10.5.0/3 [0d00h00m04s] 2023-11-01T09:47:31 <INF> [SNTP] Time is already set: 2023-11-01 09:47:31 [0d00h00m04s] 2023-11-01T09:47:31 <INF> [MAIN] CPU frequency: 160 MHz [0d00h00m05s] 2023-11-01T09:47:32 <INF> [SDCARD] Folder/file presence check started... [0d00h00m05s] 2023-11-01T09:47:32 <INF> [SDCARD] Folder/file presence check successful [0d00h00m05s] 2023-11-01T09:47:32 <INF> [MAIN] Tag: 'v15.3.0', Release: v15.3.0 (Commit: 3fbff0a), Date/Time: 2023-07-22 09:42, Web UI: Release: v15.3.0 (Commit: 3fbff0a) [0d00h00m05s] 2023-11-01T09:47:32 <INF> [MAIN] Reset reason: Via esp_restart [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WLANINI] SSID: renz [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WLANINI] Password: XXXXXXXX [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WLANINI] Hostname: wasserzähler [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WLANINI] IP-Address: 192.168.178.45 [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WLANINI] Gateway: 192.168.178.1 [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WLANINI] Netmask: 255.255.255.0 [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WLANINI] RSSIThreshold: -75 [0d00h00m05s] 2023-11-01T09:47:32 <INF> [MAIN] WLAN config loaded, init WIFI... [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WIFI] Manual interface config -> IP: 192.168.178.45, Gateway: 192.168.178.1, Netmask: 255.255.255.0 [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WIFI] No DNS server, use gateway [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WIFI] Set hostname to: wasserzähler [0d00h00m05s] 2023-11-01T09:47:32 <INF> [WIFI] Init successful [0d00h00m08s] 2023-11-01T09:47:35 <INF> [WIFI] Connected to: renz, RSSI: -53 [0d00h00m09s] 2023-11-01T09:47:35 <INF> [WIFI] Assigned IP: 192.168.178.45 [0d00h00m11s] 2023-11-01T09:47:38 <INF> [SNTP] Time is synced with NTP Server pool.ntp.org: 2023-11-01 09:47:38 [0d00h00m11s] 2023-11-01T09:47:38 <INF> [SNTP] Time is synced with NTP Server pool.ntp.org: 2023-11-01 09:47:38 [0d00h00m13s] 2023-11-01T09:47:40 <INF> [MAIN] Device info: CPU cores: 2, Chip revision: 300 [0d00h00m13s] 2023-11-01T09:47:40 <INF> [MAIN] SD card info: Name: SU16G, Capacity: 15193MB, Free: 15175MB [0d00h00m15s] 2023-11-01T09:47:42 <INF> [MAIN] Initialization completed successfully [0d00h00m17s] 2023-11-01T09:47:44 <INF> [LOGFILE] Set log level to ERROR [0d00h01m17s] 2023-11-01T09:48:44 <ERR> [POSTPROC] Zähler: Raw: 007313626000, Value: , Status: Rate too high - Read: 2147483647 - Pre: 241563 - Rate: 2147483647 [0d00h00m00s] 2023-11-01T08:52:34 <INF> [MAIN] ================================================= [0d00h00m00s] 2023-11-01T08:52:34 <INF> [MAIN] ==================== Start ====================== [0d00h00m00s] 2023-11-01T08:52:34 <INF> [MAIN] ================================================= [0d00h00m00s] 2023-11-01T08:52:35 <INF> [MAIN] PSRAM size: 8388608 byte (8MB / 64MBit) [0d00h00m00s] 2023-11-01T08:52:35 <INF> [MAIN] Total heap: 4376759 byte [0d00h00m04s] 2023-11-01T08:52:39 <INF> [MAIN] Camera info: PID: 0x26, VER: 0x42, MIDL: 0x7f, MIDH: 0xa2 [0d00h00m04s] 2023-11-01T08:52:39 <INF> [SDCARD] Basic R/W check started... [0d00h00m04s] 2023-11-01T08:52:39 <INF> [SDCARD] Basic R/W check successful [0d00h00m04s] 2023-11-01T08:52:39 <INF> [SNTP] TimeServer: pool.ntp.org [0d00h00m04s] 2023-11-01T08:52:39 <INF> [SNTP] Configuring NTP Client... [0d00h00m04s] 2023-11-01T09:52:39 <INF> [SNTP] Time zone set to CET-1CEST,M3.5.0,M10.5.0/3 [0d00h00m04s] 2023-11-01T09:52:39 <INF> [SNTP] Time is already set: 2023-11-01 09:52:39 [0d00h00m04s] 2023-11-01T09:52:39 <INF> [MAIN] CPU frequency: 160 MHz [0d00h00m05s] 2023-11-01T09:52:40 <INF> [SDCARD] Folder/file presence check started... [0d00h00m05s] 2023-11-01T09:52:40 <INF> [SDCARD] Folder/file presence check successful [0d00h00m05s] 2023-11-01T09:52:40 <INF> [MAIN] Tag: 'v15.3.0', Release: v15.3.0 (Commit: 3fbff0a), Date/Time: 2023-07-22 09:42, Web UI: Release: v15.3.0 (Commit: 3fbff0a) [0d00h00m05s] 2023-11-01T09:52:40 <INF> [MAIN] Reset reason: Via esp_restart [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WLANINI] SSID: renz [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WLANINI] Password: XXXXXXXX [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WLANINI] Hostname: wasserzähler [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WLANINI] IP-Address: 192.168.178.45 [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WLANINI] Gateway: 192.168.178.1 [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WLANINI] Netmask: 255.255.255.0 [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WLANINI] RSSIThreshold: -75 [0d00h00m05s] 2023-11-01T09:52:40 <INF> [MAIN] WLAN config loaded, init WIFI... [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WIFI] Manual interface config -> IP: 192.168.178.45, Gateway: 192.168.178.1, Netmask: 255.255.255.0 [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WIFI] No DNS server, use gateway [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WIFI] Set hostname to: wasserzähler [0d00h00m05s] 2023-11-01T09:52:40 <INF> [WIFI] Init successful [0d00h00m08s] 2023-11-01T09:52:43 <INF> [WIFI] Connected to: renz, RSSI: -54 [0d00h00m08s] 2023-11-01T09:52:43 <INF> [WIFI] Assigned IP: 192.168.178.45 [0d00h00m25s] 2023-11-01T09:53:00 <INF> [MAIN] Device info: CPU cores: 2, Chip revision: 300 [0d00h00m25s] 2023-11-01T09:53:00 <INF> [MAIN] SD card info: Name: SU16G, Capacity: 15193MB, Free: 15175MB [0d00h00m27s] 2023-11-01T09:53:02 <INF> [MAIN] Initialization completed successfully [0d00h00m30s] 2023-11-01T09:53:04 <INF> [LOGFILE] Set log level to ERROR [0d00h01m26s] 2023-11-01T09:54:01 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h06m26s] 2023-11-01T09:59:01 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h11m27s] 2023-11-01T10:04:02 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h11m48s] 2023-11-01T10:04:24 <ERR> [OTA FILE] File sending failed! [0d00h11m53s] 2023-11-01T10:04:28 <ERR> [OTA FILE] File sending failed! [0d00h12m08s] 2023-11-01T10:04:43 <ERR> [OTA FILE] File sending failed! [0d00h16m25s] 2023-11-01T10:09:01 <ERR> [POSTPROC] Zähler: Raw: 000NNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 000NNNNNN000 - Pre: 241563 [0d00h21m25s] 2023-11-01T10:14:01 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h26m25s] 2023-11-01T10:19:01 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h31m25s] 2023-11-01T10:24:01 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h36m25s] 2023-11-01T10:29:01 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h41m25s] 2023-11-01T10:34:01 <ERR> [POSTPROC] Zähler: Raw: 000NNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 000NNNNNN000 - Pre: 241563 [0d00h46m25s] 2023-11-01T10:39:01 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h51m25s] 2023-11-01T10:44:01 <ERR> [POSTPROC] Zähler: Raw: 00NNNNNNN000, Value: , Status: Neg. Rate - Read: - Raw: 00NNNNNNN000 - Pre: 241563 [0d00h01m25s] 2023-11-01T10:52:26 <ERR> [POSTPROC] Zähler: Raw: 00N3NNNNN000, Value: , Status: Rate too high - Read: 300241000 - Pre: 241563 - Rate: 299999437 [0d00h06m26s] 2023-11-01T10:57:26 <ERR> [POSTPROC] Zähler: Raw: NN2NNNN4N000, Value: , Status: Rate too high - Read: 2000241000 - Pre: 241563 - Rate: 1999999437 [0d00h07m22s] 2023-11-01T10:58:22 <ERR> [OTA FILE] File sending failed! [0d00h07m27s] 2023-11-01T10:58:27 <ERR> [OTA FILE] File sending failed!VIELEN DANK für eure HILFE!!!!
-
RE: Test Adapter micronova easy connect plusposted in Tester
@tombox Was mich wundert, warum muss ich bei HASS meine Customer Code und die API URL eingeben und hier nicht. Bei dem HASS Projekt werden generlell nur die Relevanten Funktionen abgerufen, wobei ich mir wünschen würde auch den Timer zu programmieren. Kenne mich leider damit null aus. Sorry
-
RE: Test Adapter micronova easy connect plusposted in Tester
Hi!
Erstmal danke für den Adapter, aber warum wurde hier der weg über die App gewählt?
Man kann auch direkt über die IoT Plattform gehen. Für HASS gibt es da etwas (https://github.com/fredericvl/py-agua-iot/blob/master/examples/home-assistant).
Der Login bei deinem Adapter ist zwar einfacher ( E-Mail und Passwort), aber die Objektstruktur und die Bedienung unterirdisch. Ich werde vorerst bei der Bedienung über den HASS Adapter bleiben.
nicht böse gemeint, eher als Denkanstoß
Vg Flipi
